User Manual
Table Of Contents
- NBG-418N v2
- User’s Guide
- Introduction
- The Web Configurator
- Connection Wizard
- Modes
- Tutorials
- 5.1 Overview
- 5.2 How to Connect to the Internet from an AP
- 5.3 Configure Wireless Security Using WPS on both your NBG-418N v2 and Wireless Client
- 5.4 Enable and Configure Wireless Security without WPS on your NBG-418N v2
- 5.5 Using Multiple SSIDs on the NBG-418N v2
- 5.6 Installing UPnP in Windows 7 Example
- 5.7 Using Bandwidth Management on the NBG-418N v2
- Technical Reference
- Wireless LAN
- WAN
- LAN
- DHCP Server
- Network Address Translation
- Dynamic DNS
- Static Route
- Firewall
- Content Filter
- Remote Management
- Universal Plug-and-Play (UPnP)
- Bandwidth MGMT
- System
- Logs
- Tools
- Sys OP Mode
- Language
- Troubleshooting
- Customer Support
- IP Addresses and Subnetting
- Pop-up Windows, JavaScripts and Java Permissions
- Setting Up Your Computer’s IP Address
- Wireless LANs
- Common Services
- Legal Information
- Index
Chapter 6 Wireless LAN
NBG-418N v2 User’s Guide
73
The following table describes the labels in this screen.
6.11 AP Se le c t Sc re e n
Use this screen to choose an access point that you want the NBG-418N v2 in universal repeater mode)
to connect to. You should know the security settings of the target AP.
To open this screen, click Ne twork > Wirele ss LAN > AP Se le c t tab.
Table 28 Network > Wireless LAN > MBSSID
LABEL DESCRIPTION
Network Profiles
Select Click the Se le c t radio button to select the Multiple Basic Service Set Identifier (MBSSID) you
wish to edit.
Scheme This field displays the index number of the SSID.
SSID This field displays the SSID name of the Wireless client.
Security This field displays the Se c urity mode of the wireless client. If there’s no security, it will display
None .
Status This field displays whether the Ena ble Gue st Ne twork check box of the SSID is enabled.
SSID Broadcast This field displays whether the Ena ble SSID Bro a dc a st check box of the SSID is enabled.
Wireless Settings--Profile 1
Enable Guest
Network
Click the Ena ble Gue st Ne twork check box to enable this SSID.
Enable SSID
Broadcast
Click the Ena ble SSID Broa dc a st check box to activate the SSID broadcast to different wireless
clients.
Allow Guest to
access My Local
Network
Click the Allow Gue st to a c c e ss my Lo c a l Ne two rk check box to allow the client to access the
local network resources behind the NBG-418N v2.
Enable Wireless
Isolation
Click the Enable Wire le ss Isola tion check box to keep the wireless clients in this SSID from
communicating with each other through the NBG-418N v2.
Name (SSID) This field displays the SSID name you selected using the select radio button.
Security Options--Profile1
Security Mode Select WEP or WPA- PSK(TKIP), WPA2- PSK(AES) or WPA- PSK/ WPA2- PSK AES to add security on
this wireless network. The wireless clients which want to associate to this network must have
same wireless security settings as the Device. When you select to use a security, additional
options appears in this screen.
Or you can select None to allow any client to associate this network without any data
encryption or authentication.
See
Section 6.4 on page 63 for more details about this field.
Apply Click Apply to save your changes back to the NBG-418N v2.
Reset Click Re se t to reload the previous configuration for this screen.