User’s Guide LTE3301 Series LTE Indoor Gateway Version 1.00 Edition 1, 10/2017 Default Login Details LAN IP Address User Name Password http://192.168.1.
IMPO RTANT! READ C AREFULLY BEFO RE USE. KEEP THIS G UIDE FO R FUTURE REFERENC E. Screenshots and graphics in this book may differ slightly from your product due to differences in your product firmware or your computer operating system. Every effort has been made to ensure that the information in this manual is accurate. Re la te d Do c um e nta tio n • Quick Start Guide The Quick Start Guide shows how to connect the LTE3301 and access the Web Configurator wizards.
Contents Overview C o nte nts O ve rvie w Use r’s G uide ......................................................................................................................................10 Introduction ........................................................................................................................................... 11 Introducing the Web Configurator ..................................................................................................... 16 Setup Wizard .........
Table of Contents Ta b le o f C o nte nts C o nte nts O ve rvie w .............................................................................................................................3 Ta b le o f C o nte nts .................................................................................................................................4 Pa rt I: Use r’s G uide .......................................................................................... 10 C ha pte r 1 Intro duc tio n ...............
Table of Contents 4.1 Overview ......................................................................................................................................... 30 4.2 Set Up a Wireless Network Using WPS ........................................................................................... 30 4.2.1 Push Button Configuration (PBC) ........................................................................................ 30 4.2.2 PIN Configuration ..................................................
Table of Contents 7.3.3 WPA-PSK/WPA2-PSK .............................................................................................................. 68 7.3.4 WPA/WPA2 ............................................................................................................................ 69 7.4 More AP Screen .............................................................................................................................. 70 7.4.1 More AP Edit .............................................
Table of Contents C ha pte r 11 DDNS ...................................................................................................................................................96 11.1 Overview ...................................................................................................................................... 96 11.2 General ........................................................................................................................................
Table of Contents 17.5.1 Add Bandwidth management Rule .............................................................................. 115 C ha pte r 18 Unive rsa l Plug - a nd- Pla y (UPnP) ......................................................................................................117 18.1 Overview .................................................................................................................................... 117 18.2 What You Need to Know ....................................
Table of Contents Appendix D Customer Support ..................................................................................................... 176 Appendix E Legal Information ....................................................................................................... 182 Inde x .................................................................................................................................................
PA RT I Use r’s G uide 10
C HA PTER 1 Intro duc tio n 1.1 O ve rvie w This chapter introduces the main features and applications of the LTE3301. The LTE3301 is a wireless router, which can connect to a mobile network and the Internet through a wireless WAN connection and provide easy network access to mobile users without additional wiring. You can set up a wireless network with other IEEE 802.11b/g/n compatible devices. A range of services such as a firewall and content filtering are also available for secure Internet computing.
Chapter 1 Introduction 1.3 Wa ys to Ma na g e the LTE3301 Use any of the following methods to manage the LTE3301. • WPS (Wi-Fi Protected Setup). You can use the WPS button or the WPS section of the Web Configurator to set up a wireless network with your LTE3301. • Web Configurator. This is recommended for everyday management of the LTE3301 using a (supported) web browser. 1.
Chapter 1 Introduction WPS allows you to quickly set up a wireless network with strong security, without having to configure security settings manually. Each WPS connection works between two devices. Both devices must support WPS (check each device’s documentation to make sure).
Chapter 1 Introduction The following table describes the LEDs. Table 1 Front panel LEDs LED C O LO R STATUS DESC RIPTIO N Power Green On The LTE3301 is receiving power and functioning properly. Blinking The LTE3301 is in the process of starting up or default restoring. Off Internet Green The LTE3301 is not receiving power. On The LTE3301’s WAN connection is ready. Blinking The LTE3301 is sending/receiving data through the WAN. Off LTE Green The WAN connection is not ready, or has failed.
Chapter 1 Introduction Table 2 Wall Mounting Information M4 Screws Two Screw anchors (optional) Two 1 Select a position free of obstructions on a wall strong enough to hold the weight of the device. 2 Mark two holes on the wall at the appropriate distance apart for the screws. Be c a re ful to a vo id da m a g ing pipe s o r c a b le s lo c a te d inside the wa ll whe n drilling ho le s fo r the sc re ws. 3 If using screw anchors, drill two holes for the screw anchors into the wall.
C HA PTER 2 Intro duc ing the We b C o nfig ura to r 2.1 O ve rvie w This chapter describes how to access the LTE3301 Web Configurator and provides an overview of its screens. The Web Configurator is an HTML-based management interface that allows easy setup and management of the LTE3301 via Internet browser. Use Internet Explorer 9.0 and later versions, Mozilla Firefox 21 and later versions, Safari 6.0 and later versions or Google Chrome 26.0 and later versions.
Chapter 2 Introducing the Web Configurator Fig ure 3 Login screen The following table describes the labels in this screen. Table 3 Login screen LABEL DESC RIPTIO N User Type "admin" (default) as the user name. Password Type "1234" (default) as the password. Click Lo g in. 2.2.2 Pa sswo rd Sc re e n You should see a screen asking you to change your password (highly recommended) as shown next.
Chapter 2 Introducing the Web Configurator The following table describes the labels in this screen. Table 4 Change Password Screen LABEL DESC RIPTIO N New Password Type a new password. Retype to Confirm Retype the password for confirmation. Apply Click Apply to save your changes back to the LTE3301. Ignore Click Ig no re if you do not want to change the password this time.
Chapter 2 Introducing the Web Configurator • A - Title Bar • B - Navigation Panel • C - Main Window 2.3.1 Title Ba r The title bar provides some useful links that always appear over the screens below, regardless of how deep into the Web Configurator you navigate. Fig ure 6 Title Bar The icons provide the following functions. Table 5 Title Bar: Web Configurator Icons LABEL DESC RIPTIO N Wizard Click this icon to open the setup wizard for the LTE3301.
Chapter 2 Introducing the Web Configurator The following table describes the sub-menus. Table 6 Navigation Panel LINK TAB Status FUNC TIO N This screen shows the LTE3301’s general device, system and interface status information. Use this screen to access the summary statistics tables. Mo nito r Log Use this screen to view the list of activities recorded by your LTE3301. DHCP Table Use this screen to view current DHCP client information.
Chapter 2 Introducing the Web Configurator Table 6 Navigation Panel (continued) LINK TAB FUNC TIO N Static Route Use this screen to configure IP static routes. Dynamic Routing Use this screen to enable and configure RIP on the LTE3301. Interface Group Use this screen to create a new interface group. General Use this screen to activate/deactivate the firewall. Services This screen shows a summary of the firewall rules, and allows you to edit/add a firewall rule.
Chapter 2 Introducing the Web Configurator Fig ure 8 Status Screen The following table describes the icons shown in the Sta tus screen. Table 7 Status Screen Icon Key IC O N DESC RIPTIO N Select a number of seconds or No ne from the drop-down list box to refresh all screen statistics automatically at the end of every time interval or to not refresh the screen statistics. Click this button to refresh the status screen statistics. Click this icon to see the Sta tus page.
Chapter 2 Introducing the Web Configurator The following table describes the labels shown in the Sta tus screen. Table 8 Status Screen LABEL DESC RIPTIO N Device Information Host Name This is the Syste m Na m e you enter in the Ma inte na nc e > G e ne ra l screen. It is for identification purposes. Model Number This is the model name of your device. Firmware Version This is the firmware version and the date created.
Chapter 2 Introducing the Web Configurator Table 8 Status Screen (continued) LABEL DESC RIPTIO N - CPU Usage This displays what percentage of the LTE3301’s processing ability is currently used. When this percentage is close to 100%, the LTE3301 is running at full load, and the throughput is not going to improve anymore. If you want some applications to have more throughput, you should turn off other applications (for example, using bandwidth management.
C HA PTER 3 Se tup Wiza rd 3.1 O ve rvie w This chapter provides information on the wizard setup screens in the Web Configurator. The Web Configurator’s wizard helps you configure your device to access the Internet and change the wireless LAN settings. Refer to your ISP for your Internet account information. Leave a field blank if you don’t have that information. 3.2 Ac c e ssing the Wiza rd 1 Launch your web browser and type "http://192.168.1.1" as the website address.
Chapter 3 Setup Wizard Fig ure 10 2 The LTE3301 automatically detects your location and displays the correct time zone. If the result is not correct, click De te c t Ag a in or manually select the time zone of LTE3301’s location and click Ne xt. Fig ure 11 3 Wizard: Start Wizard: Time Enter your APN (Access Point Name) provided by your service provider. Select the country where the LTE3301 is located and your service provider name. Click Ne xt.
Chapter 3 Setup Wizard Fig ure 12 4 Use this screen to enable or disable the LTE3301’s wireless LAN, and enter the wireless network name (SSID). Select a channel or use Auto to have the LTE3301 automatically determine a channel to use. Click Ne xt. Fig ure 13 5 Wizard: WAN Wizard: Wireless Settings Select WPA2- PSK and enter a pre-shared key from 8 to 63 case-sensitive characters for data encryption.
Chapter 3 Setup Wizard Fig ure 14 6 Use the read-only summary table to check whether what you have configured is correct. Click Apply Se tting s to save your settings. Otherwise, click Ba c k to go back to the previous screens. Fig ure 15 7 Wizard: Wireless Security Wizard: Summary The system takes about 35 seconds to apply settings.
Chapter 3 Setup Wizard Fig ure 16 8 Wizard: Apply Settings Click Finish to complete the wizard setup. Fig ure 17 Wizard: Finish You are now ready to connect wirelessly to your LTE3301 and access the Internet.
C HA PTER 4 Tuto ria ls 4.1 O ve rvie w This chapter provides tutorials for setting up your LTE3301. • Set Up a Wireless Network Using WPS • Connect to LTE3301 Wireless Network without WPS • Using Multiple SSIDs on the LTE3301 4.2 Se t Up a Wire le ss Ne two rk Using WPS This section gives you an example of how to set up wireless network using WPS. This example uses the LTE3301 as the AP and NWD210N as the wireless client which connects to a notebook.
Chapter 4 Tutorials Note: Your LTE3301 has a WPS button located on its panel, as well as a WPS button in its configuration utility. Both buttons have exactly the same function; you can use one or the other. Note: It doesn’t matter which button is pressed first. You must press the second button within two minutes of pressing the first one. The LTE3301 sends the proper configuration settings to the wireless client. This may take up to two minutes.
Chapter 4 Tutorials 3 Click Sta rt buttons (or button next to the PIN field) on both the wireless client utility screen and the LTE3301’s WPS Sta tio n screen within two minutes. The LTE3301 authenticates the wireless client and sends the proper configuration settings to the wireless client. This may take up to two minutes. Then the wireless client is able to communicate with the LTE3301 securely.
Chapter 4 Tutorials The instructions require that your hardware is connected (see the Quick Start Guide) and you are logged into the Web Configurator through your LAN connection (see Section 2.2 on page 16). 1 Make sure the WIFI switch (at the back panel of the LTE3301) is set to O N. 2 Open the C o nfig ura tio n > Ne two rk > Wire le ss LAN > G e ne ra l screen in the AP’s Web Configurator. 3 Confirm that the wireless LAN is enabled on the LTE3301.
Chapter 4 Tutorials 5 Open the Sta tus screen. Verify your wireless and wireless security settings under De vic e Info rm a tio n and check if the WLAN connection is up under Inte rfa c e Sta tus. 4.3.1 C o nfig ure Yo ur No te b o o k Note: In this example, we use the ZyXEL NWD6505 wireless adapter as the wireless client and use the Windows built-in utility (Windows Zero Configuration (WZC)) to connect to the wireless network. 1 The LTE3301 supports IEEE 802.11b, IEEE 802.11g, and IEEE 802.
Chapter 4 Tutorials 3 After you’ve installed the driver and attached the NWD6505 to your computer’s USB port, right-click the Wire le ss Ne two rk C o nne c tio n icon in your computer’s system tray, select and click Vie w Ava ila b le Wire le ss Ne two rks. 4 The Wire le ss Ne two rk C o nne c tio n screen displays. Click Re fre sh ne two rk list to view the available wireless APs within range. 5 Select SSID_Exa m ple 3 and click C o nne c t. 6 Type the security key in the following screen.
Chapter 4 Tutorials 7 Check the status of your wireless connection in the screen below. 8 If the wireless client keeps trying to connect to or acquiring an IP address from the LTE3301, make sure you entered the correct security key. If the connection has limited or no connectivity, make sure the DHCP server is enabled on the LTE3301. If your connection is successful, open your Internet browser and enter http://www.zyxel.com or the URL of any other web site in the address bar.
Chapter 4 Tutorials For example, you may set up three wireless networks (A , B and C ) in your office. A is for workers, B is for guests and C is specific to a VoIP device in the meeting room. A SSI D _ W or k e r C SSI D _ VoI P B SSI D _ Gue st 4.4.1 C o nfig uring Se c urity Se tting s o f Multiple SSIDs The LTE3301 is in router mode by default. This example shows you how to configure the SSIDs with the following parameters on your LTE3301 .
Chapter 4 Tutorials 7 Go to C o nfig ura tio n > Ne two rk > Wire le ss LAN > Mo re AP. Click the Edit icon of the first entry to configure wireless and security settings for SSID_Wo rke r. 8 Configure the screen as follows. In this example, you enable Intra - BSS Tra ffic for SSID_Wo rke r to allow wireless clients in the same wireless network to communicate with each other. Click Apply . 9 Click the Edit icon of the second entry to configure wireless and security settings for SSID_Vo IP.
Chapter 4 Tutorials 11 Click the Edit icon of the third entry to configure wireless and security settings for SSID_G ue st. 12 Configure the screen as follows. In this example, you enable Intra - BSS Tra ffic for SSID_G ue st to allow wireless clients in the same wireless network to communicate with each other. Click Apply .
Chapter 4 Tutorials LTE3301 Series User’s Guide 40
PA RT II Te c hnic a l Re fe re nc e 41
C HA PTER 5 Mo nito r 5.1 O ve rvie w This chapter discusses read-only information related to the device state of the LTE3301. To access the Monitor screens, click after login. You can also click the links in the Sum m a ry table of the Sta tus screen to view the packets sent/received as well as the status of wireless clients connected to the LTE3301. 5.2 Wha t Yo u C a n Do • Use the Lo g screen to see the logs for the activity on the LTE3301 (Section 5.3 on page 42).
Chapter 5 Monitor Fig ure 20 View Log You can configure which logs to display in the Vie w Lo g screen. Go to the Lo g Se tting screen and select the logs you wish to display. Click Apply to save your settings. Click C a nc e l to start the screen afresh. Fig ure 21 Log Settings 5.4 DHC P Ta b le DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server.
Chapter 5 Monitor Click Mo nito r > DHC P Ta b le or C o nfig ura tio n > Ne two rk > DHC P Se rve r > C lie nt List. Read-only information here relates to your DHCP status. The DHCP table shows current DHCP client information (including MAC Addre ss, and IP Addre ss) of all network clients using the LTE3301’s DHCP server. Fig ure 22 Monitor > DHCP Table The following table describes the labels in this screen.
Chapter 5 Monitor Fig ure 23 Monitor > Packet Statistics The following table describes the labels in this screen. Table 10 Monitor > Packet Statistics LABEL DESC RIPTIO N Port This is the LTE3301’s interface type. Status For the LAN ports, this displays the port speed and duplex setting or Do wn when the line is disconnected.
Chapter 5 Monitor Fig ure 24 Monitor > WLAN Station Status The following table describes the labels in this screen. Table 11 Monitor > WLAN Station Status LABEL DESC RIPTIO N # This is the index number of an associated wireless station. MAC Address This field displays the MAC address of an associated wireless station. Association Time This field displays the time a wireless station first associated with the LTE3301’s WLAN. 5.
Chapter 5 Monitor Table 12 Monitor > LTE Modem Status (continued) LABEL DESC RIPTIO N Module Name This displays the name of the built-in LTE module. IMEI/MEID This displays the International Mobile Equipment Number (IMEI) or Mobile Equipment Identifier (MEID), which is the serial number of the built-in LTE module. It is a unique 15-digit number used to identify a mobile device. HW Version This displays the hardware version of the built-in LTE module.
Chapter 5 Monitor Table 12 Monitor > LTE Modem Status (continued) LABEL DESC RIPTIO N RSRQ This displays the Reference Signal Received Quality (RSRQ), which is the ratio of RSRP to the E-UTRA carrier RSSI and indicates the quality of the received reference signal. SINR This displays the Signal to Interference plus Noise Ratio (SINR). A negative value means more noise than signal. PLMN This displays the Public Land Mobile Network (PLMN) code of the mobile network.
C HA PTER 6 WAN 6.1 O ve rvie w This chapter discusses the LTE3301’s WAN screens. Use these screens to configure your LTE3301 for Internet access. A WAN (Wide Area Network) connection is an outside connection to another network or the Internet. It connects your private networks such as a LAN (Local Area Network) and other networks, so that a computer in one location can communicate with computers in other locations.
Chapter 6 WAN 6.3 Wha t Yo u Ne e d To Kno w The information in this section can help you configure the screens for your WAN connection, as well as enable/disable some advanced features of your LTE3301. 3G 3G (Third Generation) is a digital, packet-switched wireless technology. Bandwidth usage is optimized as multiple users share the same channel and bandwidth is only allocated to users when they send data.
Chapter 6 WAN In the multicast example above, systems A and D comprise one multicast group. In multicasting, the server only needs to send one data stream and this is delivered to systems A and D. IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a multicast group - it is not used to carry user data. The LTE3301 supports both IGMP version 1 (IG MP v1 ), IGMP version 2 (IG MP v2 ) and IGMP version 3 (IG MP v3 ).
Chapter 6 WAN IPv6 Ra pid De plo ym e nt Use IPv6 Rapid Deployment (6rd) when the local network uses IPv6 and the ISP has an IPv4 network. When the LTE3301 has an IPv4 WAN address, you can enable 6rd to encapsulate IPv6 packets in IPv4 packets to cross the ISP’s IPv4 network. The LTE3301 generates a global IPv6 prefix from its IPv4 WAN address and tunnels IPv6 traffic to the ISP’s Border Relay router (BR in the figure) to connect to the native IPv6 Internet. The local network can also use IPv4 services.
Chapter 6 WAN Table 13 Network > WAN > Management WAN (continued) LABEL DESC RIPTIO N Status This field indicates whether the IPv4 and IPv6 connectivity is available. Modify Click the Edit icon to configure the WAN connection settings. 6.4.1 Ma na g e m e nt WAN Edit Use this screen to change your LTE3301’s 3G/4G WAN connection settings. Click the Edit icon in the Ne two rk > WAN > Ma na g e m e nt WAN screen.
Chapter 6 WAN The following table describes the labels in this screen. Table 14 Network > WAN > Management WAN Edit LABEL DESC RIPTIO N ISP Parameters for Internet Access Encapsulation This shows the WAN connection type. 3G/4G Information Dial-Up Profile Select Auto - De te c tio n to have the LTE3301 use the inserted SIM card’s default settings to connect to any available mobile network.
Chapter 6 WAN Table 14 Network > WAN > Management WAN Edit (continued) LABEL DESC RIPTIO N Connection Control Select Auto Re c o nne c t (a lwa ys- o n) if you do not want the connection to time out. Select C o nne c t- o n- De m a nd if you do not want the connection up all the time and specify an idle time-out in the Ma xim um Idle Tim e field. Maximum Idle Time Specify the time in minutes that elapses before the LTE3301 automatically disconnects from the service provider.
Chapter 6 WAN 6.5 Ne two rk Sc a n Use this screen to set how you want the LTE3301 to connect to an available mobile network. Click Ne two rk > WAN > Ne two rk Sc a n from the C o nfig ura tio n menu. Fig ure 31 Network > WAN > Network Scan The following table describes the labels in this screen. Table 15 Network > WAN > Network Scan LABEL DESC RIPTIO N Physical Interface This shows the type of the interface used by the WAN connection.
Chapter 6 WAN 6.6 IPv6 Use this screen to configure the LTE3301’s IPv6 settings. Click Ne two rk > WAN > IPv6 from the C o nfig ura tio n menu. Fig ure 32 Network > WAN > IPv6 The following table describes the labels in this screen. Table 16 Network > WAN > IPv6 LABEL DESC RIPTIO N IPv6 Select Ena b le to allow the LTE3301 to run IPv6. Otherwise, select Disa b le . IPv6 Connection Select Sta tic IPv6 if you have a fixed IPv6 address assigned by your ISP.
Chapter 6 WAN Table 16 Network > WAN > IPv6 (continued) LABEL DESC RIPTIO N (These fields appear when the IPv6 C o nne c tio n is set to DHC Pv6 .) DNS Setting Select O b ta in DNS Se rve r a ddre ss Auto m a tic a lly to have the LTE3301 get the IPv6 DNS server addresses from the ISP automatically. Select Use the fo llo wing DNS a ddre ss to have the LTE3301 use the IPv6 DNS server addresses you configure manually. Primary DNS Address Enter the first IPv6 DNS server address assigned by the ISP.
Chapter 6 WAN Table 16 Network > WAN > IPv6 (continued) LABEL DESC RIPTIO N IPv6 Address Range(End) If you select Sta te ful (DHC Pv6) , specify the range of IPv6 addresses from which the DHCPv6 server assigns to the clients. Enter the largest value of the last block of the IPv6 addresses which are to be allocated. IPv6 Address Lifetime If you select Sta te ful (DHC Pv6) , specify how long (in minutes) the IPv6 addresses remain valid.
C HA PTER 7 Wire le ss LAN 7.1 O ve rvie w This chapter discusses how to configure the wireless network settings in your LTE3301. See the appendices for more detailed information about wireless networks. The following figure provides an example of a wireless network. Fig ure 33 Example of a Wireless Network The wireless network is the part in the blue circle. In this wireless network, devices A and B are called wireless clients.
Chapter 7 Wireless LAN • Use the Adva nc e d screen to allow intra-BSS networking and set the RTS/CTS Threshold (Section 7.6 on page 74). • Use the Q o S screen to ensure Quality of Service (QoS) in your wireless network (Section 7.7 on page 75). • Use the WPS screen to quickly set up a wireless network with strong security, without having to configure security settings manually (Section 7.8 on page 75). • Use the WPS Sta tio n screen to add a wireless station using WPS (Section 7.9 on page 77).
Chapter 7 Wireless LAN You can use the MAC address filter to tell the AP which wireless clients are allowed or not allowed to use the wireless network. If a wireless client is allowed to use the wireless network, it still has to have the correct settings (SSID, channel, and security). If a wireless client is not allowed to use the wireless network, it does not matter if it has the correct settings. This type of security does not protect the information that is sent in the wireless network.
Chapter 7 Wireless LAN clients. Device A only supports WEP, and device B supports WEP and WPA. Therefore, you should set up Sta tic WEP in the wireless network. Note: It is recommended that wireless networks use WPA- PSK, WPA , or stronger encryption. IEEE 802.1x and WEP encryption are better than none at all, but it is still possible for unauthorized devices to figure out the original information pretty quickly.
Chapter 7 Wireless LAN Fig ure 34 Network > Wireless LAN > General The following table describes the general wireless LAN labels in this screen. Table 18 Network > Wireless LAN > General LABEL DESC RIPTIO N Wireless LAN Status Select Ena b le to activate the 2.4GHz wireless LAN. Select Disa b le to turn it off. You can also enable or disablethe 2.4GHz wireless LANs by using the WIFI button located on the back panel of the LTE3301.
Chapter 7 Wireless LAN Table 18 Network > Wireless LAN > General (continued) LABEL DESC RIPTIO N Channel Width Select the wireless channel width used by LTE3301. A standard 20MHz channel offers transfer speeds of up to 144Mbps (2.4GHz) whereas a 40MHz channel uses two standard channels and offers speeds of up to 300Mbps (2.4GHz). Because not all devices support 40 MHz channels, select Auto 20/ 40MHz to allow the LTE3301 to adjust the channel bandwidth automatically.
Chapter 7 Wireless LAN Note: If you do not enable any wireless security on your LTE3301, your network is accessible to any wireless networking device that is within range. Fig ure 35 Network > Wireless LAN > General: No Security The following table describes the labels in this screen. Table 19 Network > Wireless LAN > General: No Security LABEL DESC RIPTIO N Security Mode Choose No Se c urity from the drop-down list box. Apply Click Apply to save your changes back to the LTE3301.
Chapter 7 Wireless LAN Fig ure 36 Network > Wireless LAN > General: Static WEP The following table describes the wireless LAN security labels in this screen. Table 20 Network > Wireless LAN > General: Static WEP LABEL DESC RIPTIO N Security Mode Select Sta tic WEP to enable data encryption. WEP Encryption Select 64- b its or 128- b its. This dictates the length of the security key that the network is going to use. Authentication Method Select Auto or Sha re d Ke y from the drop-down list box.
Chapter 7 Wireless LAN Table 20 Network > Wireless LAN > General: Static WEP (continued) LABEL DESC RIPTIO N Key 1 to Key 4 The WEP keys are used to encrypt data. Both the LTE3301 and the wireless stations must use the same WEP key for data transmission. If you chose 64- b its, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-F"). If you chose 128- b its, then enter 13 ASCII characters or 26 hexadecimal characters ("0-9", "AF").
Chapter 7 Wireless LAN Table 21 Network > Wireless LAN > General: WPA-PSK/WPA2-PSK (continued) LABEL DESC RIPTIO N Pre-Shared Key WPA- PSK/ WPA2- PSK uses a simple common password for authentication. Type a pre-shared key from 8 to 63 case-sensitive keyboard characters. Group Key Update Timer The G ro up Ke y Upda te Tim e r is the rate at which the AP sends a new group key out to all clients. The default is 3600 seconds (60 minutes). Apply Click Apply to save your changes back to the LTE3301.
Chapter 7 Wireless LAN The following table describes the labels in this screen. Table 22 Network > Wireless LAN > General: WPA/WPA2 LABEL DESC RIPTIO N Security Mode Select WPA or WPA2 to enable data encryption. WPA Compatible This check box is available only when you select WPA2- PSK or WPA2 in the Se c urity Mo de field. Select the check box to have both WPA2 and WPA wireless clients be able to communicate with the LTE3301 even when the LTE3301 is using WPA2-PSK or WPA2.
Chapter 7 Wireless LAN The following table describes the labels in this screen. Table 23 Network > Wireless LAN > More AP LABEL DESC RIPTIO N # This is the index number of each SSID profile. Status This shows whether the SSID profile is active (a yellow bulb) or not (a gray bulb). SSID An SSID profile is the set of parameters relating to one of the LTE3301’s BSSs. The SSID (Service Set IDentifier) identifies the Service Set with which a wireless device is associated.
Chapter 7 Wireless LAN Table 24 Network > Wireless LAN > More AP: Edit (continued) LABEL DESC RIPTIO N Intra-BSS Traffic A Basic Service Set (BSS) exists when all communications between wireless clients or between a wireless client and a wired network client go through one access point (AP). Intra-BSS traffic is traffic between wireless clients in the BSS. When Intra-BSS is enabled, wireless clients can access the wired network and communicate with each other.
Chapter 7 Wireless LAN Fig ure 41 Network > Wireless LAN > MAC Filter The following table describes the labels in this menu. Table 25 Network > Wireless LAN > MAC Filter LABEL DESC RIPTIO N MAC Address Filter Select to turn on (Ena b le ) or off (Disa b le ) MAC address filtering. Filter Action Define the filter action for the list of MAC addresses in the MAC Filte r Sum m a ry table. Select Allo w to permit access to the LTE3301, MAC addresses not listed will be denied access to the LTE3301.
Chapter 7 Wireless LAN 7.6 Wire le ss LAN Adva nc e d Sc re e n Use this screen to allow wireless advanced features, such as the output power, RTS/CTS Threshold settings. Click Ne two rk > Wire le ss LAN > Adva nc e d . The screen appears as shown. Fig ure 42 Network > Wireless LAN > Advanced The following table describes the labels in this screen.
Chapter 7 Wireless LAN 7.7 Q ua lity o f Se rvic e (Q o S) Sc re e n The QoS screen allows you to automatically give a service (such as VoIP and video) a priority level. Click Ne two rk > Wire le ss LAN > Q o S. The following screen appears. Fig ure 43 Network > Wireless LAN > QoS The following table describes the labels in this screen.
Chapter 7 Wireless LAN Fig ure 44 Network > Wireless LAN > WPS The following table describes the labels in this screen. Table 28 Network > Wireless LAN > WPS LABEL DESC RIPTIO N WPS Setup WPS Select Ena b le to turn on the WPS feature. Otherwise, select Disa b le . PIN Code Select Ena b le and click Apply to allow the PIN Configuration method. If you select Disa b le , you cannot create a new PIN number. PIN Number This is the WPS PIN (Personal Identification Number) of the LTE3301.
Chapter 7 Wireless LAN 7.9 WPS Sta tio n Sc re e n Use this screen when you want to add a wireless station using WPS. To open this screen, click Ne two rk > Wire le ss LAN > WPS Sta tio n tab. Note: After you click Push Butto n on this screen, you have to press a similar button in the wireless station utility within 2 minutes. To add the second wireless station, you have to press these buttons on both device and the wireless station again after the first 2 minutes.
Chapter 7 Wireless LAN Fig ure 46 Network > Wireless LAN > Scheduling The following table describes the labels in this screen. Table 30 Network > Wireless LAN > Scheduling LABEL DESC RIPTIO N Wireless LAN Scheduling Select Ena b le to activate the wireless LAN scheduling feature. Select Disa b le to turn it off. Policy Select O n or O ff to specify whether the Wireless LAN is turned on or off. This field works in conjunction with the Da y and Fo r the fo llo wing tim e s fields.
Chapter 7 Wireless LAN Fig ure 47 Network > Wireless LAN > WDS The following table describes the labels in this screen. Table 31 Network > Wireless LAN > WDS LABEL DESC RIPTIO N WDS Setup Basic Setting Select Disa b le to turn off the WDS function on the LTE3301. Select AP+Bridg e to have the LTE3301 function as a bridge and access point simultaneously. Select Bridg e O nly to have the LTE3301 act as a wireless bridge only. Local MAC Address This shows the MAC address of the LTE3301.
C HA PTER 8 LAN 8.1 O ve rvie w This chapter describes how to configure LAN settings. A Local Area Network (LAN) is a shared communication system to which many computers are attached. A LAN is a computer network limited to the immediate area, usually the same building or floor of a building. Fig ure 48 LAN Example The LAN screens can help you configure a manage IP address, and partition your physical network into logical networks. 8.
Chapter 8 LAN Fig ure 49 LAN and WAN IP Addresses The LAN parameters of the LTE3301 are preset in the factory with the following values: • IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits) • DHCP server enabled with 32 client IP addresses starting from 192.168.1.33. These parameters should work for the majority of installations. If your ISP gives you explicit DNS server address(es), read the embedded Web Configurator help regarding what fields need to be configured. 8.
C HA PTER 9 DHC P Se rve r 9.1 O ve rvie w DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server. You can configure the LTE3301’s LAN as a DHCP server or disable it. When configured as a server, the LTE3301 provides the TCP/IP configuration for the clients. If DHCP service is disabled, you must have another DHCP server on your LAN, or else the computer must be manually configured. 9.1.
Chapter 9 DHCP Server Fig ure 51 Network > DHCP Server > General The following table describes the labels in this screen. Table 33 Network > DHCP Server > General LABEL DESC RIPTIO N DHCP Server Select Ena b le to activate DHCP for LAN. DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients (computers) to obtain TCP/IP configuration at startup from a server. Enable the DHCP server unless your ISP instructs you to do otherwise.
Chapter 9 DHCP Server Table 33 Network > DHCP Server > General (continued) LABEL DESC RIPTIO N DHCP Server IP This field is configurable only when you select DHC P Re la y . Enter the IP address of the actual remote DHCP server in this field. Lease Time This is the period of time DHCP-assigned addresses is used. DHCP automatically assigns IP addresses to clients when they log in. DHCP centralizes IP address management on central computers that run the DHCP server program.
Chapter 9 DHCP Server Fig ure 52 Network > DHCP Server > Advanced The following table describes the labels in this screen. Table 34 Network > DHCP Server > Advanced LABEL DESC RIPTIO N Static DHCP Table # This is the index number of the static IP table entry (row). MAC Address Type the MAC address (with colons) of a computer on your LAN. IP Address Type the LAN IP address of a computer on your LAN.
Chapter 9 DHCP Server 9.4 DHC P C lie nt List Sc re e n The DHCP table shows current DHCP client information (including IP Address, Host Name and MAC Address) of network clients using the LTE3301’s DHCP servers. Configure this screen to always assign an IP address to a MAC address (and host name). Click Ne two rk > DHC P Se rve r > C lie nt List. Note: You can also view a read-only client list by clicking Mo nito r > DHC P Se rve r.
C HA PTER 1 0 NAT 10.1 O ve rvie w NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. For example, the source address of an outgoing packet, used within one network is changed to a different IP address known within another network. The figure below is a simple illustration of a NAT network.
Chapter 10 NAT • Use the ALG screen to enable or disable SIP (VoIP) ALG (Application Layer Gateway) in the LTE3301 (Section 10.5 on page 92). 10.2 G e ne ra l Sc re e n Use this screen to enable NAT and set a default server. Click Ne two rk > NAT to open the G e ne ra l screen. Fig ure 55 Network > NAT > General The following table describes the labels in this screen.
Chapter 10 NAT Note: Many residential broadband ISP accounts do not allow you to run any server processes (such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location. If you are unsure, refer to your ISP. Port forwarding allows you to define the local servers to which the incoming services will be forwarded.
Chapter 10 NAT Table 37 Network > NAT > Port Forwarding (continued) LABEL DESC RIPTIO N Service Protocol Select the transport layer protocol supported by this virtual server. Choices are TC P, UDP, or TC P_UDP. If you have chosen a pre-defined service in the Se rvic e Na m e field, the protocol will be configured automatically. WAN Interface Select the WAN interface on which the matched packets are received. Port Range Specify the first and last external port numbers that identify the service.
Chapter 10 NAT Fig ure 57 Network > NAT > Port Forwarding Edit The following table describes the labels in this screen. Table 38 Network > NAT > Port Forwarding Edit LABEL DESC RIPTIO N Port Forwarding Select Ena b le to turn on this rule and the requested service can be forwarded to the host with a specified internal IP address. Select Disa b le to disallow forwarding of these ports to an inside server without having to delete the entry.
Chapter 10 NAT Fig ure 58 Network > NAT > Port Trigger The following table describes the labels in this screen. Table 39 Network > NAT > Port Trigger LABEL DESC RIPTIO N # This is the rule index number (read-only). Name Type a unique name (up to 15 characters) for identification purposes. All characters are permitted - including spaces. WAN Interface Select the WAN interface through which the matched packets are transmitted.
Chapter 10 NAT To enable and disable the SIP ALG in the LTE3301, click Ne two rk > NAT > ALG . The screen appears as shown. Fig ure 59 Network > NAT > ALG The following table describes the labels in this screen. Table 40 Network > NAT > ALG LABEL DESC RIPTIO N ALG-SIP Select Ena b le to make sure SIP (VoIP) works correctly with port-forwarding and addressmapping rules. Otherwise, select Disa b le to turn off the SIP ALG. Apply Click Apply to save your changes back to the LTE3301.
Chapter 10 NAT 10.6.2 NAT Po rt Fo rwa rding Exa m ple Let's say you want to assign ports 21-25 to one FTP, Telnet and SMTP server (A in the example), port 80 to another (B in the example) and assign a default server IP address of 192.168.1.35 to a third (C in the example). You assign the LAN IP addresses and the ISP assigns the WAN IP address. The NAT network appears as a single host on the Internet. Fig ure 60 Multiple Servers Behind NAT Example 10.6.
Chapter 10 NAT Fig ure 61 Trigger Port Forwarding Process: Example Ja ne ’s com put e r Re a l Audio Se r ve r Por t 7 0 7 0 1 Jane requests a file from the Real Audio server (port 7070). 2 Port 7070 is a “trigger” port and causes the LTE3301 to record Jane’s computer IP address. The LTE3301 associates Jane's computer IP address with the "incoming" port range of 6970-7170. 3 The Real Audio server responds using a port number ranging between 6970-7170.
C HA PTER 1 1 DDNS 11.1 O ve rvie w Dynamic Domain Name Service (DDNS) services let you use a fixed domain name with a dynamic IP address. Users can always use the same domain name instead of a different dynamic IP address that changes each time to connect to the LTE3301 or a server in your network. Note: The LTE3301 must have a public global IP address and you should have your registered DDNS account information on hand. 11.2 G e ne ra l To change your LTE3301’s DDNS, click Ne two rk > DDNS.
Chapter 11 DDNS Table 41 Dynamic DNS (continued) LABEL DESC RIPTIO N Host Name The host name is the domain name that the DDNS service will map to your dynamic global IP address. Type the host name fully qualified, for example, “yourhost.mydomain.net”. You can specify up to two host names in the field separated by a comma (","). Username Enter your user name. Password Enter the password assigned to you. IPv6 Dynamic DNS Setup Dynamic DNS Select Ena b le to use dynamic DNS.
C HA PTER 1 2 Ro uting 12.1 O ve rvie w This chapter shows you how to configure static routes for your LTE3301. The LTE3301 usually uses the default gateway to route outbound traffic from computers on the LAN to the Internet. To have the LTE3301 send data to devices not reachable through the default gateway, use static routes. For example, the next figure shows a computer (A ) connected to the LTE3301’s LAN interface.
Chapter 12 Routing Fig ure 64 Network > Routing > Static Route The following table describes the labels in this screen. Table 42 Network > Routing > Static Route LABEL DESC RIPTIO N Add Static Route Click this to create a new rule. # This is the number of an individual static route. Status This field indicates whether the rule is active (yellow bulb) or not (gray bulb). Destination This parameter specifies the IP network address of the final destination.
Chapter 12 Routing Table 43 Network > Routing > Static Route: Add/Edit LABEL DESC RIPTIO N IP Subnet Mask Enter the IP subnet mask here. Gateway IP Address Enter the IP address of the next-hop gateway. The gateway is a router or switch on the same segment as your LTE3301's interface(s). The gateway helps forward packets to their destinations. Back Click Ba c k to return to the previous screen without saving. Apply Click Apply to save your changes back to the LTE3301.
C HA PTER 1 3 Inte rfa c e G ro up 13.1 O ve rvie w By default, the four LAN interfaces on the LTE3301 are in the same group and can communicate with each other. Creating a new interface will create a new LAN bridge interface (subnet) (for example, 192.168.2.0/24) that acts as a dependent LAN network, and is a different subnet from default LAN subnet (192.168.1.0/24). 13.2 Inte rfa c e G ro up Sc re e n You can manually add a LAN/WLAN interface to a new group.
Chapter 13 Interface Group 13.2.1 Inte rfa c e G ro up > Add Sc re e n Click the Add button in the Inte rfa c e G ro up screen to open the following screen. Use this screen to create a new interface group. Note: An interface can belong to only one group at a time. Fig ure 68 Network > Interface Group > Add The following table describes the fields in this screen. Table 46 Network > Interface Group > Add LABEL DESC RIPTIO N Group Name Enter a name to identify this group.
C HA PTER 1 4 Fire wa ll 14.1 O ve rvie w Use these screens to enable and configure the firewall that protects your LTE3301 and your LAN from unwanted or malicious traffic. Enable the firewall to protect your LAN computers from attacks by hackers on the Internet and control access between the LAN and WAN. By default the firewall: • allows traffic that originates from your LAN computers to go to all of the networks. • blocks traffic that originates on the other networks from going to the LAN.
Chapter 14 Firewall Ab o ut the LTE3301 Fire wa ll The LTE3301’s firewall feature physically separates the LAN and the WAN and acts as a secure gateway for all data passing between the networks. It is a stateful inspection firewall and is designed to protect against Denial of Service attacks when activated (click the G e ne ra l tab under Fire wa ll and then click the Ena b le Fire wa ll check box).
Chapter 14 Firewall Fig ure 70 Security > Firewall > General l The following table describes the labels in this screen. Table 47 Security > Firewall > General LABEL DESC RIPTIO N Enable Firewall Select this check box to activate the firewall. The LTE3301 performs access control and protects against Denial of Service (DoS) attacks when the firewall is activated. Apply Click Apply to save the settings. Cancel Click C a nc e l to start configuring this screen again. 14.
Chapter 14 Firewall Fig ure 71 Security > Firewall > Services l The following table describes the labels in this screen. Table 48 Security > Firewall > Services LABEL DESC RIPTIO N ICMP Internet Control Message Protocol is a message control and error-reporting protocol between a host server and a gateway to the Internet. ICMP uses Internet Protocol (IP) datagrams, but the messages are processed by the TCP/IP software and directly apparent to the application user.
Chapter 14 Firewall Table 48 Security > Firewall > Services (continued) LABEL DESC RIPTIO N Source IP Address Enter the IP address of the computer that initializes traffic for the application or service. The LTE3301 applies the firewall rule to traffic initiating from this computer. Protocol Select the protocol (TC P, UDP or IC MP) used to transport the packets for which you want to apply the firewall rule.
C HA PTER 1 5 C o nte nt Filte ring 15.1 O ve rvie w This chapter shows you how to configure content filtering. Content filtering is the ability to block certain web features and specific URLs. Ke ywo rd Blo c king URL C he c king The LTE3301 checks the URL’s domain name (or IP address) and file path separately when performing keyword blocking. The URL’s domain name or IP address is the characters that come before the first slash in the URL. For example, with the URL www.zyxel.com.tw/news/pressroom.
Chapter 15 Content Filtering Fig ure 72 Security > Content Filter The following table describes the labels in this screen. Table 49 Security > Content Filter LABEL DESC RIPTIO N Trusted IP Setup To enable this feature, type an IP address of any one of the computers in your network that you want to have as a trusted computer. This allows the trusted computer to have full access to all features that are configured to be blocked by content filtering. Leave this field blank to have no trusted computers.
Chapter 15 Content Filtering Table 49 Security > Content Filter (continued) LABEL DESC RIPTIO N Add Click Add after you have typed a keyword. Repeat this procedure to add other keywords. Up to 64 keywords are allowed. When you try to access a web page containing a keyword, you will get a message telling you that the content filter is blocking this request. Delete Highlight a keyword in the lower box and click De le te to remove it. The keyword disappears from the text box after you click Apply .
C HA PTER 1 6 IPv6 Fire wa ll 16.1 O ve rvie w This chapter shows you how to enable and create IPv6 firewall rules to block unwanted IPv6 traffic. 16.2 IPv6 Fire wa ll Sc re e n Click C o nfig ura tio n > Se c urity > IPv6 Fire wa ll. The Se rvic e screen appears as shown. Fig ure 73 Configuration > Security > IPv6 Firewall The following table describes the labels in this screen.
Chapter 16 IPv6 Firewall Table 50 Configuration > Security > IPv6 Firewall (continued) LABEL DESC RIPTIO N Dest IP Address Enter the IPv6 address of the computer to which traffic for the application or service is entering. The LTE3301 applies the firewall rule to traffic destined for this computer. Source IP Address Enter the IPv6 address of the computer that initializes traffic for the application or service. The LTE3301 applies the firewall rule to traffic initiating from this computer.
C HA PTER 1 7 Ba ndwidth Ma na g e m e nt 17.1 O ve rvie w This chapter contains information about configuring bandwidth management and editing rules. ZyXEL’s Bandwidth Management allows you to specify bandwidth management rules based on an application. In the figure below, uplink traffic goes from the LAN device (A ) to the WAN device (B). Bandwidth management is applied before sending the packets out to the WAN. Downlink traffic comes back from the WAN device (B) to the LAN device (A ).
Chapter 17 Bandwidth Management The sum of the bandwidth allotments that apply to the LAN interface (WAN to LAN, WAN to WLAN) must be less than or equal to the downstream bandwidth that you configure in the Ba ndwidth Ma na g e m e nt > G e ne ra l screen Section 17.5 on page 114. 17.4 G e ne ra l Sc re e n Use this screen to have the LTE3301 apply bandwidth management. Click Ma na g e m e nt > Ba ndwidth MG MT to open the bandwidth management G e ne ra l screen.
Chapter 17 Bandwidth Management You can also use this screen to configure bandwidth management rule for other services or applications that are not on the pre-defined list of LTE3301. Additionally, you can define the IP addresses and port for a service or application. Click Ma na g e m e nt > Ba ndwidth MG MT > Adva nc e d to open the bandwidth management Adva nc e d screen. Fig ure 76 Management > Bandwidth Management > Advanced The following table describes the labels in this screen.
Chapter 17 Bandwidth Management Fig ure 77 Bandwidth Management Rule Configuration: Application List The following table describes the labels in this screen. Table 53 Bandwidth Management Rule Configuration: Application List LABEL DESC RIPTIO N Rule Select Ena b le to turn on the bandwidth management rule. Otherwise, select Disa b le . IP Address Enter the IP address or a range of IP addresses of the destination computer for whom this rule applies.
C HA PTER 1 8 Unive rsa l Plug - a nd- Pla y (UPnP) 18.1 O ve rvie w This chapter introduces the UPnP feature in the web configurator. Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.
Chapter 18 Universal Plug-and-Play (UPnP) When a UPnP device joins a network, it announces its presence with a multicast message. For security reasons, the LTE3301 allows multicast messages on the LAN only. All UPnP-enabled devices may communicate freely with each other without additional configuration. Disable UPnP if this is not your intention. 18.3 UPnP Sc re e n Use this screen to enable UPnP on your LTE3301. Click Ma na g e m e nt > UPnP to display the screen shown next.
Chapter 18 Universal Plug-and-Play (UPnP) Fig ure 79 3 In the Inte rne t C o nne c tio n Pro pe rtie s window, click Se tting s to see the port mappings there were automatically created. Fig ure 80 4 Network Connections Internet Connection Properties You may edit or delete the port mappings or click Add to manually add port mappings.
Chapter 18 Universal Plug-and-Play (UPnP) Fig ure 82 Internet Connection Properties: Advanced Settings: Add Note: When the UPnP-enabled device is disconnected from your computer, all port mappings will be deleted automatically. 5 Select Sho w ic o n in no tific a tio n a re a whe n c o nne c te d option and click O K. An icon displays in the system tray. Fig ure 83 6 System Tray Icon Double-click on the icon to display your current Internet connection status.
Chapter 18 Universal Plug-and-Play (UPnP) 3 Select My Ne two rk Pla c e s under O the r Pla c e s. Fig ure 85 Network Connections 4 An icon with the description for each UPnP-enabled device displays under Lo c a l Ne two rk. 5 Right-click on the icon for your LTE3301 and select Invo ke . The web configurator login screen displays. Fig ure 86 6 Network Connections: My Network Places Right-click on the icon for your LTE3301 and select Pro pe rtie s.
Chapter 18 Universal Plug-and-Play (UPnP) Fig ure 87 Network Connections: My Network Places: Properties: Example LTE3301 Series User’s Guide 122
C HA PTER 1 9 TR- 069 19.1 O ve rvie w This chapter explains how to configure the LTE3301’s TR-069 auto-configuration settings. 19.2 TR- 069 Sc re e n TR-069 defines how Customer Premise Equipment (CPE), for example your LTE3301, can be managed over the WAN by an Auto Configuration Server (ACS). TR-069 is based on sending Remote Procedure Calls (RPCs) between an ACS and a client device. RPCs are sent in Extensible Markup Language (XML) format over HTTP or HTTPS.
Chapter 19 TR-069 The following table describes the fields in this screen. Table 55 Maintenance > TR-069 Client LABEL DESC RIPTIO N Inform Select Ena b le for the LTE3301 to send periodic inform via TR-069 on the WAN. Otherwise, select Disa b le . Inform Interval Enter the time interval (in seconds) at which the LTE3301 sends information to the autoconfiguration server. ACS URL Enter the URL or IP address of the auto-configuration server.
C HA PTER 2 0 Ma inte na nc e 20.1 O ve rvie w This chapter provides information on the Ma inte na nc e screens. 20.2 Wha t Yo u C a n Do • Use the G e ne ra l screen to set the timeout period of the management session (Section 20.3 on page 125). • Use the Ac c o unt screen to change your LTE3301’s system password (Section 20.4 on page 126). • Use the Tim e screen to change your LTE3301’s time and date (Section 20.5 on page 127).
Chapter 20 Maintenance Table 56 Maintenance > General (continued) LABEL DESC RIPTIO N Administrator Inactivity Timer Type how many minutes a management session can be left idle before the session times out. The default is 300 seconds. After it times out you have to log in with your password again. Very long idle timeouts may have security risks. A value of "0" means a management session never times out, no matter how long it has been left idle (not recommended).
Chapter 20 Maintenance Fig ure 91 Maintenance > Account > Edit The following table describes the labels in this screen. Table 58 Maintenance > Account > Edit LABEL DESC RIPTIO N Username Enter a descriptive name for the user account. The user name can be up to 15 alphanumeric characters (0-9, A-Z, a-z, -, _ with no spaces). Old Password Type the default password or the existing password you use to access the system in this field. New Password Type your new system password (up to 30 characters).
Chapter 20 Maintenance Fig ure 92 Maintenance > Time The following table describes the labels in this screen. Table 59 Maintenance > Time LABEL DESC RIPTIO N Current Time and Date Current Time This field displays the time of your LTE3301. Each time you reload this page, the LTE3301 synchronizes the time with the time server. Current Date This field displays the date of your LTE3301. Each time you reload this page, the LTE3301 synchronizes the date with the time server.
Chapter 20 Maintenance Table 59 Maintenance > Time (continued) LABEL DESC RIPTIO N Time Zone Choose the time zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Savings Daylight saving is a period from late spring to early fall when many countries set their clocks ahead of normal local time by one hour to give more daytime light in the evening.
Chapter 20 Maintenance Fig ure 93 Maintenance > Firmware Upgrade The following table describes the labels in this screen. Table 60 Maintenance > Firmware Upgrade LABEL DESC RIPTIO N File Path Type in the location of the file you want to upload in this field or click Bro wse ... to find it. Browse... Click Bro wse ... to find the .bin file you want to upload. Remember that you must decompress compressed (.zip) files before you can upload them. Upload Click Uplo a d to begin the upload process.
Chapter 20 Maintenance Click Ma inte na nc e > Ba c kup/ Re sto re . Information related to factory defaults, backup configuration, and restoring configuration appears as shown next. Fig ure 95 Maintenance > Backup/Restore The following table describes the labels in this screen. Table 61 Maintenance > Backup/Restore LABEL DESC RIPTIO N Backup Click Ba c kup to save the LTE3301’s current configuration to your computer.
Chapter 20 Maintenance 20.8 Re sta rt Sc re e n System restart allows you to reboot the LTE3301 without turning the power off. Click Ma inte na nc e > Re sta rt to open the following screen. Fig ure 96 Maintenance > Restart Click Re sta rt to have the LTE3301 reboot. This does not affect the LTE3301's configuration.
C HA PTER 2 1 Tro ub le sho o ting 21.1 O ve rvie w This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. • Power, Hardware Connections, and LEDs • LTE3301 Access and Login • Internet Access • Wireless Connections 21.2 Po we r, Ha rdwa re C o nne c tio ns, a nd LEDs The LTE3301 does not turn on. None of the LEDs turn on. 1 Make sure you are using the power adaptor or cord included with the LTE3301.
Chapter 21 Troubleshooting 21.3 LTE3301 Ac c e ss a nd Lo g in I don’t know the IP address of my LTE3301. 1 The default IP address of the LTE3301 is 192.168.1.1 . 2 If you changed the IP address and have forgotten it, you might get the IP address of the LTE3301 by looking up the IP address of the default gateway for your computer. To do this in most Windows computers, click Sta rt > Run, enter c m d , and then enter ipc o nfig .
Chapter 21 Troubleshooting 5 Reset the device to its factory defaults, and try to access the LTE3301 with the default IP address. See Section 1.5 on page 12. 6 If the problem continues, contact the network administrator or vendor, or try one of the advanced suggestions. Adva nc e d Sug g e stio ns • Try to access the LTE3301 using another service, such as Telnet. If you can access the LTE3301, check the firewall rules to find out why the LTE3301 does not respond to HTTP.
Chapter 21 Troubleshooting 1 Check the hardware connections, and make sure the LEDs are behaving as expected. See the Quick Start Guide and Section 1.8 on page 13. 2 Reboot the LTE3301. 3 If the problem continues, contact your ISP. The Internet connection is slow or intermittent. 1 There might be a lot of traffic on the network. Look at the LEDs, and check Section 1.8 on page 13.
Chapter 21 Troubleshooting I set up URL keyword blocking, but I can still access a website that should be blocked. Make sure that the keywords that you type are listed in the rule’s Ke ywo rd List. What factors may cause intermittent or unstabled wireless connection? How can I solve this problem? The following factors may cause interference: • Obstacles: walls, ceilings, furniture, and so on. • Building Materials: metal doors, aluminum studs.
A PPEN DIX A Po p- up Windo ws, Ja va Sc ript a nd Ja va Pe rm issio ns In order to use the web configurator you need to allow: • Web browser pop-up windows from your device. • JavaScript (enabled by default). • Java permissions (enabled by default). Note: The screens used below belong to Internet Explorer version 6, 7 and 8. Screens for other Internet Explorer versions may vary. Inte rne t Explo re r Po p- up Blo c ke rs You may have to disable pop-up blocking to log into your device.
Appendix A Pop-up Windows, JavaScript and Java Permissions Fig ure 98 3 Internet Options: Privacy Click Apply to save this setting. Ena b le Po p- up Blo c ke rs with Exc e ptio ns Alternatively, if you only want to allow pop-up windows from your device, see the following steps. 1 In Internet Explorer, select To o ls, Inte rne t O ptio ns and then the Priva c y tab. 2 Select Se tting s… to open the Po p- up Blo c ke r Se tting s screen.
Appendix A Pop-up Windows, JavaScript and Java Permissions Fig ure 99 Internet Options: Privacy 3 Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.167.1. 4 Click Add to move the IP address to the list of Allo we d site s.
Appendix A Pop-up Windows, JavaScript and Java Permissions 5 Click C lo se to return to the Priva c y screen. 6 Click Apply to save this setting. Ja va Sc ript If pages of the web configurator do not display properly in Internet Explorer, check that JavaScript are allowed. 1 In Internet Explorer, click To o ls, Inte rne t O ptio ns and then the Se c urity tab. Fig ure 101 Internet Options: Security 2 Click the C usto m Le ve l... button. 3 Scroll down to Sc ripting .
Appendix A Pop-up Windows, JavaScript and Java Permissions Fig ure 102 Security Settings - Java Scripting Ja va Pe rm issio ns 1 From Internet Explorer, click To o ls, Inte rne t O ptio ns and then the Se c urity tab. 2 Click the C usto m Le ve l... button. 3 Scroll down to Mic ro so ft VM . 4 Under Ja va pe rm issio ns make sure that a safety level is selected. 5 Click O K to close the window.
Appendix A Pop-up Windows, JavaScript and Java Permissions Fig ure 103 Security Settings - Java JAVA (Sun) 1 From Internet Explorer, click To o ls, Inte rne t O ptio ns and then the Adva nc e d tab. 2 Make sure that Use Ja va 2 fo r under Ja va (Sun) is selected. 3 Click O K to close the window.
Appendix A Pop-up Windows, JavaScript and Java Permissions Mo zilla Fire fo x Mozilla Firefox 2.0 screens are used here. Screens for other versions may vary slightly. The steps below apply to Mozilla Firefox 3.0 as well. You can enable Java, Javascript and pop-ups in one screen. Click To o ls, then click O ptio ns in the screen that appears. Fig ure 105 Mozilla Firefox: TOOLS > Options Click C o nte nt to show the screen below. Select the check boxes as shown in the following screen.
Appendix A Pop-up Windows, JavaScript and Java Permissions O pe ra Opera 10 screens are used here. Screens for other versions may vary slightly. Allo wing Po p- Ups From Opera, click To o ls, then Pre fe re nc e s. In the G e ne ra l tab, go to C ho o se ho w yo u pre fe r to ha ndle po p- ups and select O pe n a ll po p- ups. Fig ure 107 Opera: Allowing Pop-Ups Ena b ling Ja va From Opera, click To o ls, then Pre fe re nc e s. In the Adva nc e d tab, select C o nte nt from the left-side menu.
Appendix A Pop-up Windows, JavaScript and Java Permissions Fig ure 108 Opera: Enabling Java To customize JavaScript behavior in the Opera browser, click Ja va Sc ript O ptio ns. Fig ure 109 Opera: JavaScript Options Select the items you want Opera’s JavaScript to apply.
A PPEN DIX B Se tting Up Yo ur C o m pute r’s IP Addre ss Note: Your specific LTE3301 may not support all of the operating systems described in this appendix. See the product specifications for more information about which operating systems are supported. This appendix shows you how to configure the IP settings on your computer in order for it to be able to communicate with the other devices on your network.
Appendix B Setting Up Your Computer’s IP Address 2 In the C o ntro l Pa ne l, click the Ne two rk C o nne c tio ns icon. 3 Right-click Lo c a l Are a C o nne c tio n and then select Pro pe rtie s. 4 On the G e ne ra l tab, select Inte rne t Pro to c o l (TC P/ IP) and then click Pro pe rtie s.
Appendix B Setting Up Your Computer’s IP Address 5 The Inte rne t Pro to c o l TC P/ IP Pro pe rtie s window opens.
Appendix B Setting Up Your Computer’s IP Address 6 Select O b ta in a n IP a ddre ss a uto m a tic a lly if your network administrator or ISP assigns your IP address dynamically. Select Use the fo llo wing IP Addre ss and fill in the IP a ddre ss, Sub ne t m a sk, and De fa ult g a te wa y fields if you have a static IP address that was assigned to you by your network administrator or ISP.
Appendix B Setting Up Your Computer’s IP Address 4 Click Ma na g e ne two rk c o nne c tio ns. 5 Right-click Lo c a l Are a C o nne c tio n and then select Pro pe rtie s. Note: During this procedure, click C o ntinue whenever Windows displays a screen saying that it needs your permission to continue. 6 Select Inte rne t Pro to c o l Ve rsio n 4 (TC P/ IPv4) and then select Pro pe rtie s.
Appendix B Setting Up Your Computer’s IP Address 7 The Inte rne t Pro to c o l Ve rsio n 4 (TC P/ IPv4) Pro pe rtie s window opens.
Appendix B Setting Up Your Computer’s IP Address 8 Select O b ta in a n IP a ddre ss a uto m a tic a lly if your network administrator or ISP assigns your IP address dynamically. Select Use the fo llo wing IP Addre ss and fill in the IP a ddre ss, Sub ne t m a sk, and De fa ult g a te wa y fields if you have a static IP address that was assigned to you by your network administrator or ISP.
Appendix B Setting Up Your Computer’s IP Address 3 Click C ha ng e a da pte r se tting s. 4 Double click Lo c a l Are a C o nne c tio n and then select Pro pe rtie s.
Appendix B Setting Up Your Computer’s IP Address Note: During this procedure, click C o ntinue whenever Windows displays a screen saying that it needs your permission to continue. 5 Select Inte rne t Pro to c o l Ve rsio n 4 (TC P/ IPv4) and then select Pro pe rtie s. 6 The Inte rne t Pro to c o l Ve rsio n 4 (TC P/ IPv4) Pro pe rtie s window opens.
Appendix B Setting Up Your Computer’s IP Address 7 Select O b ta in a n IP a ddre ss a uto m a tic a lly if your network administrator or ISP assigns your IP address dynamically. Select Use the fo llo wing IP Addre ss and fill in the IP a ddre ss, Sub ne t m a sk, and De fa ult g a te wa y fields if you have a static IP address that was assigned to you by your network administrator or ISP.
Appendix B Setting Up Your Computer’s IP Address Ma c O S X: 10.3 a nd 10.4 The screens in this section are from Mac OS X 10.4 but can also apply to 10.3. 1 Click Apple > Syste m Pre fe re nc e s. 2 In the Syste m Pre fe re nc e s window, click the Ne two rk icon.
Appendix B Setting Up Your Computer’s IP Address 3 When the Ne two rk preferences pane opens, select Built- in Ethe rne t from the network connection type list, and then click C o nfig ure . 4 For dynamically assigned settings, select Using DHC P from the C o nfig ure IPv4 list in the TC P/ IP tab.
Appendix B Setting Up Your Computer’s IP Address 5 For statically assigned settings, do the following: • From the C o nfig ure IPv4 list, select Ma nua lly . • In the IP Addre ss field, type your IP address. • In the Sub ne t Ma sk field, type your subnet mask. • In the Ro ute r field, type the IP address of your device. 6 Click Apply No w and close the window.
Appendix B Setting Up Your Computer’s IP Address Fig ure 110 Mac OS X 10.4: Network Utility Ma c O S X: 10.5 a nd 10.6 The screens in this section are from Mac OS X 10.5 but can also apply to 10.6. 1 Click Apple > Syste m Pre fe re nc e s. 2 In Syste m Pre fe re nc e s, click the Ne two rk icon.
Appendix B Setting Up Your Computer’s IP Address 3 When the Ne two rk preferences pane opens, select Ethe rne t from the list of available connection types. 4 From the C o nfig ure list, select Using DHC P for dynamically assigned settings.
Appendix B Setting Up Your Computer’s IP Address 5 For statically assigned settings, do the following: • From the C o nfig ure list, select Ma nua lly . • In the IP Addre ss field, enter your IP address. • In the Sub ne t Ma sk field, enter your subnet mask. • In the Ro ute r field, enter the IP address of your LTE3301. 6 Click Apply and close the window.
Appendix B Setting Up Your Computer’s IP Address Fig ure 111 Mac OS X 10.5: Network Utility Linux: Ub untu 8 (G NO ME) This section shows you how to configure your computer’s TCP/IP settings in the GNU Object Model Environment (GNOME) using the Ubuntu 8 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration. The following screens use the default Ubuntu 8 installation.
Appendix B Setting Up Your Computer’s IP Address 3 In the Authe ntic a te window, enter your admin account name and password then click the Authe ntic a te button. 4 In the Ne two rk Se tting s window, select the connection that you want to configure, then click Pro pe rtie s.
Appendix B Setting Up Your Computer’s IP Address 5 The Pro pe rtie s dialog box opens. • In the C o nfig ura tio n list, select Auto m a tic C o nfig ura tio n (DHC P) if you have a dynamic IP address. • In the C o nfig ura tio n list, select Sta tic IP a ddre ss if you have a static IP address. Fill in the IP a ddre ss, Sub ne t m a sk, and G a te wa y a ddre ss fields. 6 Click O K to save the changes and close the Pro pe rtie s dialog box and return to the Ne two rk Se tting s screen.
Appendix B Setting Up Your Computer’s IP Address 8 Click the C lo se button to apply the changes. Ve rifying Se tting s Check your TCP/IP properties by clicking Syste m > Adm inistra tio n > Ne two rk To o ls, and then selecting the appropriate Ne two rk de vic e from the De vic e s tab. The Inte rfa c e Sta tistic s column shows data if your connection is working properly.
Appendix B Setting Up Your Computer’s IP Address Fig ure 112 Ubuntu 8: Network Tools Linux: o pe nSUSE 10.3 (KDE) This section shows you how to configure your computer’s TCP/IP settings in the K Desktop Environment (KDE) using the openSUSE 10.3 Linux distribution. The procedure, screens and file locations may vary depending on your specific distribution, release version, and individual configuration. The following screens use the default openSUSE 10.3 installation.
Appendix B Setting Up Your Computer’s IP Address 2 When the Run a s Ro o t - KDE su dialog opens, enter the admin password and click O K. 3 When the Ya ST C o ntro l C e nte r window opens, select Ne two rk De vic e s and then click the Ne two rk C a rd icon.
Appendix B Setting Up Your Computer’s IP Address 4 When the Ne two rk Se tting s window opens, click the O ve rvie w tab, select the appropriate connection Na m e from the list, and then click the C o nfig ure button.
Appendix B Setting Up Your Computer’s IP Address Fig ure 113 6 openSUSE 10.3: Network Card Setup Select Dyna m ic Addre ss (DHC P) if you have a dynamic IP address. Select Sta tic a lly a ssig ne d IP Addre ss if you have a static IP address. Fill in the IP a ddre ss, Sub ne t m a sk, and Ho stna m e fields. 7 Click Ne xt to save the changes and close the Ne two rk C a rd Se tup window.
Appendix B Setting Up Your Computer’s IP Address 9 Click Finish to save your settings and close the window. Ve rifying Se tting s Click the KNe two rk Ma na g e r icon on the Ta sk b a r to check your TCP/IP properties. From the O ptio ns submenu, select Sho w C o nne c tio n Info rm a tio n. Fig ure 114 openSUSE 10.3: KNetwork Manager When the C o nne c tio n Sta tus - KNe two rk Ma na g e r window opens, click the Sta tistic s ta b to see if your connection is working properly.
Appendix B Setting Up Your Computer’s IP Address Fig ure 115 openSUSE: Connection Status - KNetwork Manager LTE3301 Series User’s Guide 172
A PPEN DIX C C o m m o n Se rvic e s The following table lists some commonly-used services and their associated protocols and port numbers. For a comprehensive list of port numbers, ICMP type/code numbers and services, visit the IANA (Internet Assigned Number Authority) web site. • Na m e : This is a short, descriptive name for the service. You can use this one or create a different one, if you like. • Pro to c o l: This is the type of IP protocol used by the service.
Appendix C Common Services Table 62 Commonly Used Services (continued) NAME PRO TO C O L PO RT(S) DESC RIPTIO N ICMP User-Defined 1 Internet Control Message Protocol is often used for diagnostic or routing purposes. ICQ UDP 4000 This is a popular Internet chat program. IGMP (MULTICAST) User-Defined 2 Internet Group Management Protocol is used when sending packets to a specific group of hosts. IKE UDP 500 The Internet Key Exchange algorithm is used for key distribution and management.
Appendix C Common Services Table 62 Commonly Used Services (continued) NAME PRO TO C O L PO RT(S) DESC RIPTIO N STRM WORKS UDP 1558 Stream Works Protocol. SYSLOG UDP 514 Syslog allows you to send system logs to a UNIX server. TACACS UDP 49 Login Host Protocol used for (Terminal Access Controller Access Control System). TELNET TCP 23 Telnet is the login and terminal emulation protocol common on the Internet and in UNIX environments. It operates over TCP/IP networks.
A PPEN DIX D C usto m e r Suppo rt In the event of problems that cannot be solved by using this manual, you should contact your vendor. If you cannot contact your vendor, then contact a Zyxel office for the region in which you bought the device. See http ://www.zyxe l.c o m/ho me p a g e .shtml and also http ://www.zyxe l.c o m/a b o ut_zyxe l/zyxe l_wo rldwide .shtml for the latest information. Please have the following information ready when you contact an office.
Appendix D Customer Support Ko re a • Zyxel Korea Corp. • http://www.zyxel.kr Ma la ysia • Zyxel Malaysia Sdn Bhd. • http://www.zyxel.com.my Pa kista n • Zyxel Pakistan (Pvt.) Ltd. • http://www.zyxel.com.pk Philippine s • Zyxel Philippines • http://www.zyxel.com.ph Sing a po re • Zyxel Singapore Pte Ltd. • http://www.zyxel.com.sg Ta iwa n • Zyxel Communications Corporation • http://www.zyxel.com/tw/zh/ Tha ila nd • Zyxel Thailand Co., Ltd • http://www.zyxel.co.
Appendix D Customer Support Be lg ium • Zyxel Communications B.V. • http://www.zyxel.com/be/nl/ • http://www.zyxel.com/be/fr/ Bulg a ria • Zyxel България • http://www.zyxel.com/bg/bg/ C ze c h Re pub lic • Zyxel Communications Czech s.r.o • http://www.zyxel.cz De nm a rk • Zyxel Communications A/S • http://www.zyxel.dk Esto nia • Zyxel Estonia • http://www.zyxel.com/ee/et/ Finla nd • Zyxel Communications • http://www.zyxel.fi Fra nc e • Zyxel France • http://www.zyxel.
Appendix D Customer Support La tvia • Zyxel Latvia • http://www.zyxel.com/lv/lv/homepage.shtml Lithua nia • Zyxel Lithuania • http://www.zyxel.com/lt/lt/homepage.shtml Ne the rla nds • Zyxel Benelux • http://www.zyxel.nl No rwa y • Zyxel Communications • http://www.zyxel.no Po la nd • Zyxel Communications Poland • http://www.zyxel.pl Ro m a nia • Zyxel Romania • http://www.zyxel.com/ro/ro Russia • Zyxel Russia • http://www.zyxel.ru Slo va kia • Zyxel Communications Czech s.r.o.
Appendix D Customer Support • http://www.zyxel.ch/ Turke y • Zyxel Turkey A.S. • http://www.zyxel.com.tr UK • Zyxel Communications UK Ltd. • http://www.zyxel.co.uk Ukra ine • Zyxel Ukraine • http://www.ua.zyxel.com La tin Am e ric a Arg e ntina • Zyxel Communication Corporation • http://www.zyxel.com/ec/es/ Bra zil • Zyxel Communications Brasil Ltda. • https://www.zyxel.com/br/pt/ Ec ua do r • Zyxel Communication Corporation • http://www.zyxel.
Appendix D Customer Support No rth Am e ric a USA • Zyxel Communications, Inc. - North America Headquarters • http://www.zyxel.com/us/en/ O c e a nia Austra lia • Zyxel Communications Corporation • http://www.zyxel.com/au/en/ Afric a So uth Afric a • Nology (Pty) Ltd. • http://www.zyxel.co.
A PPEN DIX E Le g a l Info rm a tio n C o pyrig ht Copyright © 2017 by Zyxel Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of Zyxel Communications Corporation.
Appendix E Legal Information • This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Appendix E Legal Information • the GSM1800 is 588.84 mW • WiFi 2.4GHz is 80.17 mW Български (Bulgarian) С настоящото Zyxel декларира, че това оборудване е в съответствие със съществените изисквания и другите приложими разпоредбите на Директива 2014/53/ЕC. Na tio na l Re stric tio ns • • • The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Please check http://www.bipt.be for more details.
Appendix E Legal Information Română (Romanian) Prin prezenta, Zyxel declară că acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale Directivei 2014/53/EU. Slovenčina (Slovak) Zyxel týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 2014/53/EU. Slovenščina (Slovene) Zyxel izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 2014/53/EU.
Appendix E Legal Information • • CAUTION: Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instruction. Dispose them at the applicable collection point for the recycling of electrical and electronic devices. For detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the store where you purchased the product.
Appendix E Legal Information 以下訊息僅適用於產品操作於 5.25-5.35 秭赫頻帶內並銷售至台灣地區 • 在 5.25-5.
Appendix E Legal Information proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of Zyxel. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. No te Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser.
Index Inde x service providers 96, 111 A DHCP 43, 82 DHCP server see also Dynamic Host Configuration Protocol ACS 123 ActiveX 109 DHCP server 81, 82 Address Assignment 50 disclaimer 182 Auto Configuration Server, see ACS 123 DNS 85 DNS Server 50 DNS server 85 B Domain Name System 85 Domain Name System. See DNS.
Index G M General wireless LAN screen 63 MAC 72 MAC address 61 MAC address filter 61 MAC address filtering 72 I MAC filter 72 IGMP version 50 managing the device good habits 12 using the web configurator. See web configurator. using the WPS. See WPS.
Index ACS setup 123 R trigger port 94 Trigger port forwarding 94 example 94 process 94 RADIUS server 62 remote management TR-069 123 Remote Procedure Calls, see RPCs 123 Reset button 12 U Reset the device 12 Restore configuration 131 Universal Plug and Play 117 Application 117 Security issues 117 Roaming 74 RPPCs 123 RTS/CTS Threshold 61, 74 UPnP 117 URL Keyword Blocking 109 user authentication 62 local (user) database 62 RADIUS server 62 S Scheduling 77 User Name 97 Service and port numbers 107
Index SSID 61 Wireless security 61 overview 61 type 61 wireless security 136 Wireless tutorial 30 Wizard setup 25 WLAN button 13 WPA compatible 63 WPS 12 LTE3301 Series User’s Guide 192
