ZyXEL G-2000 Plus 802.11g Wireless 4-port Router Quick Start Guide Version 3.
ZyAIR G-2000 Plus Quick Start Guide Table of Contents 1 Introducing the ZyAIR ................................................................................................................ 3 2 Hardware Connections............................................................................................................... 4 2.1 Side Panel and Connections ................................................................................................. 4 2.2 The LED Display ...............................
ZyAIR G-2000 Plus Quick Start Guide 1 Introducing the ZyAIR The ZyAIR G-2000 Plus is a broadband sharing gateway with a built-in wireless LAN access point and four-port switch that makes it easy for people to set up a small home/office network and share Internet access via a broadband (cable/DSL) modem. Key features of the ZyAIR include 802.1x wireless LAN security, WPA (Wi-Fi Protected Access), internal RADIUS server, firewall, remote management and UPnP.
ZyAIR G-2000 Plus Quick Start Guide 2 Hardware Connections 2.1 Side Panel and Connections Figure 1 ZyAIR Side Panel and Connections LABEL DESCRIPTION LAN Use an Ethernet cable to connect at least one computer for initial ZyAIR configuration. These ports are auto-negotiating (can connect at 10 or 100Mbps) and auto-crossover (automatically adjust to the type of Ethernet cable you use (straight-through or crossover)).
ZyAIR G-2000 Plus Quick Start Guide ZyAIR LED Figure 2 ZyAIR Front Panel Table 1 ZyAIR Front Panel LED Description LED ZyAIR COLOR Blue STATUS Blinking (Breathing) DESCRIPTION ZyAIR is sending/receiving data through the wireless LAN.
ZyAIR G-2000 Plus Quick Start Guide Table 1 ZyAIR Front Panel LED Description LED COLOR STATUS DESCRIPTION On The ZyAIR is ready, but is not sending/receiving data. Off The LED has been disabled in the web configurator or SMT. Off The Ethernet connection is not ready, or has failed. On The ZyAIR has a successful 10Mbps Ethernet connection. Blinking The ZyAIR is sending/receiving data. On The ZyAIR has a successful 100Mbps Ethernet connection. Blinking The ZyAIR is sending/receiving data.
ZyAIR G-2000 Plus Quick Start Guide Skip this section if your computer’s IP address is already between 192.168.1.2 and 192.168.1.254 with subnet mask 255.255.255.0. Your computer must have a network card and TCP/IP installed. TCP/IP should already be installed on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems. Refer to the Setting Up Your Computer’s IP Address appendix for other operating systems. 3.
ZyAIR G-2000 Plus Quick Start Guide 4. Select Internet Protocol (TCP/IP) and then click Properties. 5. Select Use the following IP Address and fill in an IP address (between 192.168.1.3 and 192.168.1.254). 6. Type 255.255.255.0 as the Subnet mask. 7. Click Advanced.1 Figure 5 Local Area Connection Properties Figure 6 Internet Protocol Properties 8. 1 Remove any previously installed gateways in the IP Settings tab and click OK to go back to the Internet Protocol TCP/IP Properties screen.
ZyAIR G-2000 Plus Quick Start Guide No gateways configured. Figure 7 Advanced TCP/IP Settings 9. Click OK to close the Internet Protocol (TCP/IP) Properties window. 10. Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 11. Close the Network Connections window (Network and Dial-up Connections in Windows 2000/NT). 3.2 Checking/Updating Your Computer’s IP Address 1. In the computer, click Start, (All) Programs, Accessories and then Command Prompt. 2.
ZyAIR G-2000 Plus Quick Start Guide 3. Press ENTER. The following screen displays. C:\>ping 192.168.1.1 Pinging 192.168.1.1 with 32 bytes of data: Reply Reply Reply Reply from from from from 192.168.1.1: 192.168.1.1: 192.168.1.1: 192.168.1.1: bytes=32 bytes=32 bytes=32 bytes=32 time=10ms time<10ms time<10ms time<10ms TTL=254 TTL=254 TTL=254 TTL=254 Ping statistics for 192.168.1.
ZyAIR G-2000 Plus Quick Start Guide Default password. 3. It is highly recommended you change the default password! Enter a new password, retype it to confirm and click Apply; alternatively click Ignore to proceed to the Replace Factory Default Certificate screen. If you do not change the password, the following screen appears every time you login. Change default password. 4.
