User`s guide
Table Of Contents
- VMG8924-B10A and VMG8924- B30A Series
- User’s Guide
- Technical Reference
- Network Map and Status Screens
- Broadband
- Wireless
- Home Networking
- 7.1 Overview
- 7.2 The LAN Setup Screen
- 7.3 The Static DHCP Screen
- 7.4 The UPnP Screen
- 7.5 Installing UPnP in Windows Example
- 7.6 Using UPnP in Windows XP Example
- 7.7 The Additional Subnet Screen
- 7.8 The STB Vendor ID Screen
- 7.9 The 5th Ethernet Port Screen
- 7.10 The LAN VLAN Screen
- 7.11 The Wake on LAN Screen
- 7.12 Technical Reference
- Routing
- Quality of Service (QoS)
- Network Address Translation (NAT)
- Dynamic DNS Setup
- Interface Group
- USB Service
- Power Management
- Firewall
- MAC Filter
- Parental Control
- Scheduler Rule
- Certificates
- VPN
- Voice
- Log
- Traffic Status
- VoIP Status
- ARP Table
- Routing Table
- IGMP/MLD Status
- xDSL Statistics
- 3G Statistics
- User Account
- Remote Management
- TR-069 Client
- TR-064
- SNMP
- Time Settings
- E-mail Notification
- Logs Setting
- Firmware Upgrade
- Configuration
- Diagnostic
- Troubleshooting
- Customer Support
- Setting up Your Computer’s IP Address
- IP Addresses and Subnetting
- Pop-up Windows, JavaScripts and Java Permissions
- Wireless LANs
- IPv6
- Services
- Legal Information
- Index
Chapter 6 Wireless
VMG8924-B10A and VMG8924-B30A Series User’s Guide
88
6.6 The WMM Screen
Use this screen to enable Wi-Fi MultiMedia (WMM) and WMM Power Save in wireless networks for
multimedia applications.
Click Network Setting > Wireless > WMM. The following screen displays.
Figure 42 Network Setting > Wireless > WMM
The following table describes the labels in this screen.
Register Enter the PIN of the device that you are setting up a WPS connection with and click
Register to authenticate and add the wireless device to your wireless network.
You can find the PIN either on the outside of the device, or by checking the device’s
settings.
Note: You must also activate WPS on that device within two minutes to have it present its PIN
to the Device.
Method 3 Use this section to set up a WPS wireless network by entering the PIN of the Device into the
client.
Release
Configuratio
n
The default WPS status is configured.
Click this button to remove all configured wireless and wireless security settings for WPS
connections on the Device.
Generate
New PIN
Number
The PIN (Personal Identification Number) of the Device is shown here. Enter this PIN in the
configuration utility of the device you want to connect to using WPS.
The PIN is not necessary when you use WPS push-button method.
Click the Generate New PIN Number button to have the Device create a new PIN.
Apply Click Apply to save your changes.
Cancel Click Cancel to restore your previously saved settings.
Table 23 Network Setting > Wireless > WPS (continued)
LABEL DESCRIPTION
Table 24 Network Setting > Wireless > WMM
LABEL DESCRIPTION
WMM Select On to have the Device automatically give a service a priority level according to the
ToS value in the IP header of packets it sends. WMM QoS (Wifi MultiMedia Quality of
Service) gives high priority to voice and video, which makes them run more smoothly.
WMM
Automatic
Power Save
Delivery
Select this option to extend the battery life of your mobile devices (especially useful for
small devices that are running multimedia applications). The Device goes to sleep mode to
save power when it is not transmitting data. The AP buffers the packets sent to the Device
until the Device "wakes up". The Device wakes up periodically to check for incoming data.
Note: Note: This works only if the wireless device to which the Device is connected also
supports this feature.