User`s guide
Table Of Contents
- VMG8924-B10A and VMG8924- B30A Series
- User’s Guide
- Technical Reference
- Network Map and Status Screens
- Broadband
- Wireless
- Home Networking
- 7.1 Overview
- 7.2 The LAN Setup Screen
- 7.3 The Static DHCP Screen
- 7.4 The UPnP Screen
- 7.5 Installing UPnP in Windows Example
- 7.6 Using UPnP in Windows XP Example
- 7.7 The Additional Subnet Screen
- 7.8 The STB Vendor ID Screen
- 7.9 The 5th Ethernet Port Screen
- 7.10 The LAN VLAN Screen
- 7.11 The Wake on LAN Screen
- 7.12 Technical Reference
- Routing
- Quality of Service (QoS)
- Network Address Translation (NAT)
- Dynamic DNS Setup
- Interface Group
- USB Service
- Power Management
- Firewall
- MAC Filter
- Parental Control
- Scheduler Rule
- Certificates
- VPN
- Voice
- Log
- Traffic Status
- VoIP Status
- ARP Table
- Routing Table
- IGMP/MLD Status
- xDSL Statistics
- 3G Statistics
- User Account
- Remote Management
- TR-069 Client
- TR-064
- SNMP
- Time Settings
- E-mail Notification
- Logs Setting
- Firmware Upgrade
- Configuration
- Diagnostic
- Troubleshooting
- Customer Support
- Setting up Your Computer’s IP Address
- IP Addresses and Subnetting
- Pop-up Windows, JavaScripts and Java Permissions
- Wireless LANs
- IPv6
- Services
- Legal Information
- Index
Chapter 5 Broadband
VMG8924-B10A and VMG8924-B30A Series User’s Guide
47
WAN IP Address
The WAN IP address is an IP address for the Device, which makes it accessible from an outside
network. It is used by the Device to communicate with other devices in other networks. It can be
static (fixed) or dynamically assigned by the ISP each time the Device tries to access the Internet.
If your ISP assigns you a static WAN IP address, they should also assign you the subnet mask and
DNS server IP address(es).
ATM
Asynchronous Transfer Mode (ATM) is a WAN networking technology that provides high-speed data
transfer. ATM uses fixed-size packets of information called cells. With ATM, a high QoS (Quality of
Service) can be guaranteed. ATM uses a connection-oriented model and establishes a virtual circuit
(VC) between Finding Out More
PTM
Packet Transfer Mode (PTM) is packet-oriented and supported by the VDSL2 standard. In PTM,
packets are encapsulated directly in the High-level Data Link Control (HDLC) frames. It is designed
to provide a low-overhead, transparent way of transporting packets over DSL links, as an
alternative to ATM.
3G
3G (Third Generation) is a digital, packet-switched wireless technology. Bandwidth usage is
optimized as multiple users share the same channel and bandwidth is only allocated to users when
they send data. It allows fast transfer of voice and non-voice data and provides broadband Internet
access to mobile devices.
IPv6 Introduction
IPv6 (Internet Protocol version 6), is designed to enhance IP address size and features. The
increase in IPv6 address size to 128 bits (from the 32-bit IPv4 address) allows up to 3.4 x 10
38
IP
addresses. The Device can use IPv4/IPv6 dual stack to connect to IPv4 and IPv6 networks, and
supports IPv6 rapid deployment (6RD).
IPv6 Addressing
The 128-bit IPv6 address is written as eight 16-bit hexadecimal blocks separated by colons (:). This
is an example IPv6 address 2001:0db8:1a2b:0015:0000:0000:1a2f:0000.
IPv6 addresses can be abbreviated in two ways:
• Leading zeros in a block can be omitted. So
2001:0db8:1a2b:0015:0000:0000:1a2f:0000 can be written as
2001:db8:1a2b:15:0:0:1a2f:0.