User`s guide
Table Of Contents
- VMG8924-B10A and VMG8924- B30A Series
- User’s Guide
- Technical Reference
- Network Map and Status Screens
- Broadband
- Wireless
- Home Networking
- 7.1 Overview
- 7.2 The LAN Setup Screen
- 7.3 The Static DHCP Screen
- 7.4 The UPnP Screen
- 7.5 Installing UPnP in Windows Example
- 7.6 Using UPnP in Windows XP Example
- 7.7 The Additional Subnet Screen
- 7.8 The STB Vendor ID Screen
- 7.9 The 5th Ethernet Port Screen
- 7.10 The LAN VLAN Screen
- 7.11 The Wake on LAN Screen
- 7.12 Technical Reference
- Routing
- Quality of Service (QoS)
- Network Address Translation (NAT)
- Dynamic DNS Setup
- Interface Group
- USB Service
- Power Management
- Firewall
- MAC Filter
- Parental Control
- Scheduler Rule
- Certificates
- VPN
- Voice
- Log
- Traffic Status
- VoIP Status
- ARP Table
- Routing Table
- IGMP/MLD Status
- xDSL Statistics
- 3G Statistics
- User Account
- Remote Management
- TR-069 Client
- TR-064
- SNMP
- Time Settings
- E-mail Notification
- Logs Setting
- Firmware Upgrade
- Configuration
- Diagnostic
- Troubleshooting
- Customer Support
- Setting up Your Computer’s IP Address
- IP Addresses and Subnetting
- Pop-up Windows, JavaScripts and Java Permissions
- Wireless LANs
- IPv6
- Services
- Legal Information
- Index
Chapter 7 Home Networking
VMG8924-B10A and VMG8924-B30A Series User’s Guide
127
The following table describes the labels in this screen.
7.11 The Wake on LAN Screen
Use this screen to turn on a device on the LAN network. To use this feature, the remote device must
also support Wake On LAN.
You need to know the MAC address of the LAN device. It may be on a label on the device or in its
documentation.
Click Network Setting > Home Networking > Wake on Lan to open this screen.
Figure 63 Network Setting > Home Networking > Wake on Lan
The following table describes the labels in this screen.
Table 37 Network Setting > Home Networking > LAN VLAN
LABEL DESCRIPTION
Lan Port These represent the Device’s LAN ports.
Tag Operation Select what you want the Device to do to the IEEE 802.1q VLAN ID and priority tags of
downstream traffic before sending it out through this LAN port.
• Unchange - Don’t do anything to the traffic’s VLAN ID and priority tags.
• Add - Add VLAN ID and priority tags to untagged traffic.
• Remove - Delete one tag from tagged traffic. If the frame has double tags, this removes
the outer tag. This does not affect untagged traffic.
• Remark - Change the value of the outer VLAN ID and priority tags.
802.1P Mark Use this option to set what to do for the IEEE 802.1p priority tags when you add or remark
the tags for a LAN port’s downstream traffic. Either select Unchange to not modify the
traffic’s priority tags or select an priority from 0 to 7 to use. The larger the number, the
higher the priority.
VLAN ID If you will add or remark tags for this LAN port’s downstream traffic, specify the VLAN ID
(from 0 to 4094) to use here.
Apply Click Apply to save your changes.
Cancel
Click Cancel to exit this screen without saving.
Table 38 Network Setting > Home Networking > Wake on Lan
LABEL DESCRIPTION
Wake by
Address
Select Manual and enter the IP address or MAC address of the device to turn it on remotely.
The drop-down list also lists the IP addresses that can be found in the Device’s ARP table.
Select an IP address and it will then automatically update the IP address and MAC address
in the following fields.
IP Address Enter the IPv4 IP address of the device to turn it on.
MAC Address Enter the MAC address of the device to turn it on. A MAC address consists of six
hexadecimal character pairs.
Wake up Click this to send a wake up packet to wake up the specified device.