P-660R-T1/T3 v2 Quick Start Guide P-660R-T1/T3 v2 ADSL2+ Access Router Quick Start Guide Version 3.
P-660R-T1/T3 v2 Quick Start Guide Overview This Quick Start Guide shows you how to: 1 Connect the Hardware 2 Set Up Internet Access 1 Connect the Hardware 3 1 2 1 ETHERNET: Use an Ethernet cable to connect a computer to the ETHERNET port for Internet access. 2 DSL: Use a telephone wire to connect your P-660R-T1/T3 v2’s DSL port to a telephone jack (or to a splitter, if one is already installed). 3 POWER: Use only the included power adaptor to connect the POWER socket to an appropriate power source.
P-660R-T1/T3 v2 Quick Start Guide After you’ve made the connections, push in the power button to turn on the P-660R-T1/T3 v2. Look at the LEDs. • The POWER LED blinks while performing system testing. It then turns steady on if the testing is successful. • The DSL LED blinks then turns steady on, and blinks when there is traffic. • The ETHERNET LED turns on if the ETHERNET port is properly connected, and blinks when there is traffic.
P-660R-T1/T3 v2 Quick Start Guide You can also view the connection status, see: D: View the Status Screen " Configuration Genie and Zero configuration are only able to configure the device automatically for Internet access if you are using PPPoE, PPPoA or ENET ENCAP encapsulation with a dynamically-assigned IP address from your ISP. If you are not using these Internet access settings, then use the Web Configurator Internet Access Wizard to manually configure the device.
P-660R-T1/T3 v2 Quick Start Guide B: Zero Configuration Launch your web browser and navigate to any web site (for example, www.zyxel.com). The P-660R-T1/T3 v2 automatically detects and configures your Internet connection. This may take about two minutes. If you have a PPPoE or PPPoA connection, a screen displays prompting you to enter your Internet account information. Enter the username, password and/or system password exactly as provided. Click Apply.
P-660R-T1/T3 v2 Quick Start Guide C: Web Configurator Internet Access Wizard " Enter the Internet access information given to you by your ISP exactly in each wizard screen. If not given, leave the fields set to the default. 1 In your browser, go to http://192.168.1.1. 2 Enter the administrator password 1234. V If your browser cannot find this screen, see the Troubleshooting section.
P-660R-T1/T3 v2 Quick Start Guide 3 It is strongly recommended that you change the default password in the next screen. If you change it, you will not see this screen the next time you log in. 4 Select Go to Wizard setup and click Apply. You will need information supplied by your Internet service provider (ISP).
P-660R-T1/T3 v2 Quick Start Guide 5 Follow the directions in each wizard screen. Enter the Internet access information exactly supplied by your ISP. If not given, leave the fields at the default setting. 6 When you are finished exit the wizard and browse out to any website (for example www.zyxel.com) to test your connection. V See the Troubleshooting section if you cannot access the Internet.
P-660R-T1/T3 v2 Quick Start Guide V If your browser cannot find this screen, see the Troubleshooting section. 3 The status screen displays your Internet access information. See the User’s Guide for full description of this screen. Troubleshooting 1 If you cannot access the web configurator using Internet Explorer in Windows XP or Windows Server 2003, take the following steps. A) Check the cable connection from your computer to the P-660R-T1/T3 v2.
P-660R-T1/T3 v2 Quick Start Guide B) Make sure you enter the password correctly (the field is case sensitive). If you have forgotten the P-660R-T1/T3 v2’s password, use the RESET button. Press the button in for about 10 seconds (or until the POWER light starts to blink), then release it. It returns the P-660R-T1/T3 v2 to the factory defaults (IP address 192.168.1.1, password 1234).
P-660R-T1/T3 v2 Quick Start Guide 2 If you cannot access the Internet when your computer is connected to the ETHERNET port, follow these steps. A) Check the lights on the front panel. If they are different from what is described in section 1, make sure the connections are correct. If the lights are still different, turn off the device, wait a few seconds, and turn it on again. B) Follow the steps in Set Up Internet Access section again. Make sure you enter the correct information.
P-660R-T1/T3 v2 Quick Start Guide 2 In the Control Panel, double-click Network Connections (Network and Dial-up Connections in Windows 2000/ NT). 3 Right-click Local Area Connection then click Properties. 4 Select Internet Protocol (TCP/IP) then click Properties.
P-660R-T1/T3 v2 Quick Start Guide 5 The TCP / IP Properties window appears. Select obtain an IP address automatically and click OK to have the P-660R-T1/T3 v2 assign your computer an IP address. 6 If your Internet Service Provider (ISP) gave you Domain Name System (DNS) settings, enter them in the Use the following DNS server addresses fields. If you are not sure of your DNS settings, contact your ISP. 7 Click Advanced.
P-660R-T1/T3 v2 Quick Start Guide Close the Network Connections window (Network and Dial-up Connections in Windows 2000/NT). Procedure to View a Product’s Certification(s) 1 Go to www.zyxel.com. 2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3 Select the certification you wish to view from this page.
P-660R-T1/T3 v2 Quick Start Guide 14
