Prestige 2602R Series ADSL VoIP IAD Quick Start Guide Version 3.
Prestige 2602R Series Quick Start Guide Overview The Prestige P2602R ADSL VoIP IAD (Integrated Access Device) is an ADSL router with two phone ports for Voice over IP (VoIP) calls. See the User’s Guide for more information on all features. The following figure shows your Prestige (A) connected to the Internet. 1 Hardware Connections You need the following before you start: Note: You may need your Internet access and voice account information.
Prestige 2602R Series Quick Start Guide Do the following to make hardware connections for initial setup. 1 DSL: Connect the Prestige to a telephone jack using the included telephone wire. 2 LAN: Use an Ethernet cable to connect a computer or external hub to the LAN port for initial configuration and/or Internet access. 3 Phone 1-2: Connect one or more analog telephones to these ports using telephone wires. These are FXS (Foreign Exchange Station) ports.
Prestige 2602R Series Quick Start Guide • Web Configurator Internet Access Wizard 2.1 Zero Configuration Launch your web browser and navigate to any web site (for example, www.zyxel.com). The Prestige automatically detects and configures your Internet connection. This may take about two minutes. If you have a PPPoE or PPPoA connection, a screen displays prompting you to enter your Internet account information. Enter the username, password and/or service name exactly as provided. Click Apply.
Prestige 2602R Series Quick Start Guide Note: If you do not see the next screen, then please read Section 3.1 on page 10. 2 Click Login (the default password 1234 is already entered). 3 Type a new password (retype it to confirm) and click Apply. You then see the main web configurator screen 4 In the Site Map screen, click Wizard Setup. 2.2.
Prestige 2602R Series Quick Start Guide 1 From the Mode drop-down list box, select Routing (default) if you want to use routing features such as NAT. 2 The next wizard screen varies depending on the Encapsulation you chose in the first wizard screen. From the Network Address Translation drop-down list box, select SUA Only if you have one public IP address, Full Feature if you have more than one public IP address (for translation) or None to disable NAT.
Prestige 2602R Series Quick Start Guide Note: You will only see the next two screens in Routing mode. • PPPoA • RFC1483 2.2.2 Voice Configuration 3 Fill in the fields with information from your voice service provider. Leave the default settings in fields for which no information was provided (except if otherwise specified). Note: You should have a voice account already set up. This screen configures SIP account 1. Use the VoIP screens to configure SIP account 2.
Prestige 2602R Series Quick Start Guide 4 Verify your LAN, WAN and SIP settings. To change the LAN settings, click Change LAN Configuration; otherwise click Save Settings to save the configuration and go to the final wizard screen. If you change the Prestige’s LAN IP address, you must use the new IP address if you want to access the web configurator again. 5 Click Save Settings in the screen shown in step 4 to go to the final wizard screen.
Prestige 2602R Series Quick Start Guide 2.4 Make Calls Through the Internet When the VoIP LED turns on, your SIP account is registered successfully. Dial a numerical SIP number (like “12345” for example) on your phone’s keypad. Use speed dial entries for peer-to-peer calls or SIP numbers that use letters. Dial the speed dial entry on your telephone’s keypad. Use your voice service provider’s dialing plan to call regular telephone numbers.
Prestige 2602R Series Quick Start Guide PROBLEM CORRECTIVE ACTION Cannot make voice calls. Make sure you have the wizard screens properly configured. You can also check the Prestige’s IP addresses and VoIP status in the Maintenance Status screen. If the VoIP settings are correct, use speed dial to make peer-to-peer calls. If you can make a call using speed dial, there may be something wrong with the SIP server, contact your voice service provider. 3.