User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
99
The following table describes the labels in this screen.
Table 32 Network > Wireless LAN > WDS
LABEL DESCRIPTION
WDS Setup
Basic Settings
Select the operating mode for your MWR222.
• AP + Bridge - The MWR222 functions as a bridge and access point
simultaneously.
• Bridge - The MWR222 acts as a wireless network bridge. It
establishes wireless links with other APs. You need to know the MAC
address of the peer device, which also must be in bridge mode. The
MWR222 can establish up to five wireless links with other APs.
Local MAC
Address
This is the MAC address of your MWR222.
Phy Mode
Select the Phy mode you want the MWR222 to use. This dictates the
maximum size of packets during data transmission.
Remote MAC
Address
This is the MAC address of the peer device that your MWR222 wants to
make a bridge connection with.
You can connect to up to 4 peer devices.
Security
EncrypType
Select whether to use WEP, TKIP or AES encryption for your WDS
connection in this field.
Otherwise, select No Security.
EncrypKey
The Encryp key is used to encrypt data. Peers must use the same key for
data transmission.
Apply Click Apply to save your changes to MWR222.
Refresh Click Refresh to reload the previous configuration for this screen.