User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
70
this is done user can no longer use the wired connection for the web
configurator.)
•
Open your browser and log into the MWR222. Click on Configuration >
Network > Wired WAN, for the encryption select “PPPoE” and enter your
PPPoE “Username and Password.”
8.2.2 Cable Modem
•
Connect the cable modem to your MWR222 on the WAN port. (MWR222
has only one Ethernet port, and it is configured to be a LAN port by
default. So user has to change the configuration first so that the Ethernet
port can act as the WAN port. Once this is done user can no longer use the
wired connection for the web configurator.)
•
Unplug the power to your cable modem. Depending on your cable modem,
it may also have a backup battery inside. Remove this battery and
completely power down the cable modem. Let it sit from 2 to 3 minutes
and then reconnect the battery and power to the cable modem.
•
If the router is set with its default settings it should automatically connect
to the Internet.
8.2.3 3G USB Adapter
•
Activate the 3G USB adapter on a PC first, using the software provided by
the ISP.
•
Connect the 3G USB adapter to the USB port on the back of the MWR222
•
Log into your MWR222 using your computer’s browser.
•
Click on the Configuration tab at the left side of the screen.
•
Click on “Network” under the configuration tab, and then click on “WAN”.
•
On the WAN configuration page, click on the Mobile WAN tab at the top of
the page. Then fill in the account information you obtained from the
mobile broad band ISP. Make sure you check “Nailed-Up Connection.”
•
After filling in all the account information, click the “Connect” button to
save the information to the router’s memory and make the wireless 3G
connection.
•
The USB LED starts to blink fast, indicating MWR222 is connecting. When
the mobile WAN is connected, the USB LED changes solid on. However, if
the Ethernet port is configured to WAN, and is connected to a wired WAN,
the mobile WAN will be used as the backup WAN so the USB LED shows
slow blinking.