User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
60
Rate
For the LAN ports, this displays the port speed and duplex setting or N/A
when the line is disconnected.
For the WAN port, it displays the port speed and duplex setting if you’re
using Ethernet encapsulation and Idle (line (ppp) idle), Dial (starting to
trigger a call) and Drop (dropping a call) if you're using PPPoE or PPTP
encapsulation. This field displays N/A when the line is disconnected.
For the WLAN, it displays the maximum transmission rate when the
WLAN is enabled and N/A when the WLAN is disabled.
Summary
BW MGMT Monitor
Click Details... to go to the Monitor > BW MGMT Monitor screen.
Use this screen to view the amount of network bandwidth that
applications running in the network are using.
DHCP Table
Click Details... to go to the Monitor > DHCP Table screen. Use
this screen to view current DHCP client information.
Packet Statistics
Click Details... to go to the Monitor > Packet Statistics screen.
Use this screen to view port status and packet specific statistics.
7.5 Wireless LAN General Screen
Use this screen to configure the wireless LAN settings of your MWR222. Go to
Configuration > Wireless LAN > General to open the following screen.
Figure 26 WISP Mode: LAN > General Screen
The following table describes the labels in this screen.