User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
47
Figure 18 Pop up for Access Point mode
Click OK. The Web Configurator refreshes once the change to Access Point mode
is successful.
6.3.2 Accessing the Web Configurator in Access Point
Mode
Log in to the Web Configurator in Access Point mode, do the following:
1 Connect your computer to the LAN port of the MWR222.
2 The default IP address of the MWR222 is “192.168.10.2”. In this case,
your computer must have an IP address in the range between
“192.168.10.3” and “192.168.10.254”.
3 Click Start > Run on your computer in Windows. Type “cmd” in the dialog
box to open the Command Prompt. Once in the Command Prompt, type
“ipconfig” and press enter to show your computer’s IP address. If your
computer’s IP address is not in the correct range then see Appendix C for
information on changing your computer’s IP address.
4 After you’ve set your computer’s IP address, open a web browser such as
Internet Explorer and type “192.168.10.2” as the web address in your web
browser.
Note: After clicking Login, see the screens described in the following sections.
6.3.3 Configuring your WLAN, Bandwidth
Management and Maintenance Settings
The configuration of wireless, bandwidth management and maintenance settings
in Access Point mode is the same as for Router Mode.
• See Chapter 10 for information on configuring your wireless network.