User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
176
21.3.1 Remote Management and NAT
When NAT is enabled:
• Use the MWR222’s WAN IP address when configuring from the WAN.
• Use the MWR222’s LAN IP address when configuring from the LAN.
21.3.2 System Timeout
There is a default system management idle timeout of five minutes (three hundred
seconds). The MWR222 automatically logs you out if the management session
remains idle for longer than this timeout period. The management session does not
time out when a statistics screen is polling. You can change the timeout period in the
System screen
21.4 WWW Screen
To change your MWR222’s remote management settings, click Management >
Remote Management > WWW.
Figure 89 Management > Remote Management > WWW
The following table describes the labels in this screen
Table 59 Management > Remote Management > WWW
LABEL DESCRIPTION
Server Port
You may change the server port number for a service if needed,
however you must use the same port number in order to use that
service for remote management.
Server Access
Select the interface(s) through which a computer may access the
MWR222 using this service.
Secured Client
IP Address
Select All to allow all computes to access the MWR222.
Otherwise, check Selected and specify the IP address of the computer
that can access the MWR222.