User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
138
13.4 NAT Application Screen
Use the Application screen to forward incoming service requests to the server(s)
on your local network. You may enter a single port number or a range of port
numbers to be forwarded, and the local IP address of the desired server. The port
number identifies a service; for example, web service is on port 80 and FTP on
port 21. In some cases, such as for unknown services or where one server can
support more than one service (for example both FTP and web service), it might
be better to specify a range of port numbers.
In addition to the servers for specified services, NAT supports a default server. A
service request that does not have a server explicitly designated for it is
forwarded to the default server. If the default is not defined, the service request
is simply discarded.
Note: Many residential broadband ISP accounts do not allow you to run any server
processes (such as a Web or FTP server) from your location. Your ISP may
periodically check for servers and may suspend your account if it discovers any
active services at your location. If you are unsure, refer to your ISP.
Port forwarding allows you to define the local servers to which the incoming
services will be forwarded. To change your MWR222’s port forwarding settings,
click Network > NAT > Application. The screen appears as shown.
Note: If you do not assign a Default Server IP address in the NAT > General screen,
the MWR222 discards all packets received for ports that are not specified in this
screen or remote management.
Refer to Appendix E for port numbers commonly used for particular services.