User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
121
Failure
WiMAX Configuration
Realm
Enter this field accordingly provided by your ISP. In most cases, it
can be left blank unless ISP notices otherwise.
WiMAX Signal
Threshold
WiMAX signal threshold marked with CINR in dB, which stands for
“Carrier Interferrence and Noise Ratio.” MWR detects CINR when it
tries to connect to a WiMAX base station. The value is default at
“15” and is better when its higher.
LTE/3G Configuration
Username
Type the user name given to you by your mobile provider. (not all
ISP needs this)
Password
Type the password associated with the User Name above. (not all
ISP needs this)
Retype to Confirm
Type your password again to make sure that you have enter the
password correctly.
Access Point Name
Phone Number
Nailed-up
Connection
Select Nailed-Up Connection if you do not want the connection
to time out.
Idle Timeout (sec)
This value specifies the time in minutes that elapses before the
MWR222 automatically disconnects from the mobile connection.
PIN Code
Type the Pin Code given to you by your mobile broadband provider.
Enable Data Usage
Counter
Select this option to enable the Data Usage Counter settings.
The data usage counter is for user convenience. It is not
synchronized with the Carrier’s actual data usage.