User`s guide
Table Of Contents
- About This User's Guide
- Document Conventions
- Safety Warnings
- Table of Contents
- Part I: Introduction
- 1. Getting to Know Your MWR222
- 2.
- 2. Introducing the Web Configurator
- 3. Monitor
- 4.
- 4.
- 4. MWR222 Modes
- 5. Router Mode
- 6. Access Point Mode
- 5.
- 5.
- 7. WISP Mode
- 7
- 7
- 8 Tutorials
- 8.3 Connecting to Internet from an Access Point
- 8.4 Configuring Wireless Security Using WPS
- 9 Wireless LAN
- 9.1 Overview
- 9.2 What You Can Do
- Use the General screen to enable the Wireless LAN, enter the SSID and select the wireless security mode.
- 9.3 What You Should Know
- 9.4 General Wireless LAN Screen
- 9.5 Security
- 9.6 MAC Filter
- 9.7 Wireless LAN Advanced Screen
- 9.8 Quality of Service (QoS) Screen
- 9.9 WPS Screen
- 9.10 WPS Station Screen
- 9.11 Scheduling Screen
- 9.12 WDS Screen
- 10.1 Overview
- 10.2 What You Can Do
- 10.3 What You Need To Know
- 10.2
- 10.3
- 10.4 Internet Connection
- 10.5 Mobile WAN
- 10.7 IGMP Snooping Screen
- 11 LAN
- 12 DHCP Server
- 13. Network Address Translation (NAT)
- 14 Dynamic DNS
- 15. OpenDNS
- 16 Static Route
- 17.
- 17.
- 17. Routing Information Protocol
- Part III
- Part V
- Maintenance and Troubleshooting
- Part VI
- Appendices and Index
- Appendix A
- Pop-up Windows, JavaScripts and Java Permissions
- End-User License Agreement for “MWR222”
- NOTE: Some components of this product incorporate free software programs covered under the open source code licenses which allows you to freely copy, modify and redistribute the software. For at least three (3) years from the date of distribution of t...
- Notice
- Information herein is subject to change without notice. Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any p...
- Notice
- GNU GENERAL PUBLIC LICENSE
- GNU LESSER GENERAL PUBLIC LICENSE
MWR211 User’s Guide
108
The following table describes the labels in this screen.
Table 34 Network > WAN > Wired WAN: PPPoE Encapsulation
LABEL DESCRIPTION
Ethernet Port Configuration
Ethernet Port
Type
Select WAN when using the Ethernet port for WAN configuration
ISP Parameters for Internet Access
Encapsulation Select PPP over Ethernet if you connect to your Internet via dial-up.
User Name Type the user name given to you by your ISP.
Password Type the password associated with the user name above.
Retype to
Confirm
Type your password again to make sure that you have entered is
correctly.
MTU Size
Enter the Maximum Transmission Unit (MTU) or the largest packet size
per frame that your MWR222 can receive and process.
Nailed-Up
Connection
Select Nailed-Up Connection if you do not want the connection to
time out.
Idle Timeout
(sec)
This value specifies the time in minutes that elapses before the router
automatically disconnects from the PPPoE server.
WAN IP Address Assignment
Get
automatically
from ISP
Select this option If your ISP did not assign you a fixed IP address. This
is the default selection.
Use Fixed IP
Address
Select this option If the ISP assigned a fixed IP address.
My WAN IP
Address
Enter your WAN IP address in this field if you selected Use Fixed IP
Address.