User`s guide
Table Of Contents
- User’s Guide
- Introduction and Hardware
- Basic Configuration
- Advanced
- VLAN
- Static MAC Forward Setup
- Filtering
- Spanning Tree Protocol
- 11.1 STP/RSTP Overview
- 11.1.1 STP Terminology
- 11.1.2 How STP Works
- 11.1.3 STP Port States
- 11.1.4 Multiple RSTP
- 11.2 Spanning Tree Protocol Main Screen
- 11.3 Configure Rapid Spanning Tree Protocol
- 11.4 Rapid Spanning Tree Protocol Status
- 11.5 Configure Multiple Rapid Spanning Tree Protocol
- 11.6 Multiple Rapid Spanning Tree Protocol Status
- Bandwidth Control
- Broadcast Storm Control
- Mirroring
- Link Aggregation
- Port Authentication
- Port Security
- Classifier
- Policy Rule
- Queuing Method
- VLAN Stacking
- Multicast
- 22.1 Multicast Overview
- 22.1.1 IP Multicast Addresses
- 22.1.2 IGMP Filtering
- 22.1.3 IGMP Snooping
- 22.2 Multicast Status
- 22.3 Multicast Setting
- 22.4 IGMP Filtering Profile
- 22.5 MVR Overview
- 22.5.1 Types of MVR Ports
- 22.5.2 MVR Modes
- 22.5.3 How MVR Works
- 22.6 General MVR Configuration
- 22.7 MVR Group Configuration
- 22.7.1 MVR Configuration Example
- IP Application
- Management
- Maintenance
- 28.1 The Maintenance Screen
- 28.2 Firmware Upgrade
- 28.3 Restore a Configuration File
- 28.4 Backup a Configuration File
- 28.5 Load Factory Default
- 28.6 Save Configuration
- 28.7 Reboot System
- 28.8 FTP Command Line
- 28.8.1 Filename Conventions
- 28.8.2 FTP Command Line Procedure
- 28.8.3 GUI-based FTP Clients
- 28.8.4 FTP Restrictions
- Access Control
- 29.1 Access Control Overview
- 29.2 The Access Control Main Screen
- 29.3 About SNMP
- 29.3.1 Supported MIBs
- 29.3.2 SNMP Traps
- 29.3.3 Configuring SNMP
- 29.4 SSH Overview
- 29.5 How SSH works
- 29.6 SSH Implementation on the Switch
- 29.6.1 Requirements for Using SSH
- 29.7 Introduction to HTTPS
- 29.8 HTTPS Example
- 29.8.1 Internet Explorer Warning Messages
- 29.8.2 Netscape Navigator Warning Messages
- 29.8.3 The Main Screen
- 29.9 Service Port Access Control
- 29.10 Remote Management
- Diagnostic
- Syslog
- Cluster Management
- MAC Table
- IP Table
- ARP Table
- Routing Table
- Configure Clone
- Maintenance
- CLI and Troubleshooting
- Introducing Commands
- 38.1 Overview
- 38.2 Accessing the CLI
- 38.2.1 The Console Port
- 38.3 The Login Screen
- 38.4 Command Syntax Conventions
- 38.5 Changing the Password
- 38.6 Privilege Levels
- 38.7 Command Modes
- 38.8 Getting Help
- 38.8.1 List of Available Commands
- 38.9 Using Command History
- 38.10 Saving Your Configuration
- 38.10.1 Configuration File
- 38.10.2 Logging Out
- 38.11 Command Summary
- 38.11.1 User Mode
- 38.11.2 Enable Mode
- 38.11.3 General Configuration Mode
- 38.11.4 interface port-channel Commands
- 38.11.5 interface route-domain Commands
- 38.11.6 config-vlan Commands
- 38.12 mvr Commands
- User and Enable Mode Commands
- 39.1 Overview
- 39.2 show Commands
- 39.2.1 show system-information
- 39.2.2 show ip
- 39.2.3 show logging
- 39.2.4 show interface
- 39.2.5 show mac address-table
- 39.3 ping
- 39.4 traceroute
- 39.5 Copy Port Attributes
- 39.6 Configuration File Maintenance
- 39.6.1 Using a Different Configuration File
- 39.6.2 Resetting to the Factory Default
- Configuration Mode Commands
- 40.1 Change the Out of Band Management IP Address
- 40.2 Enabling IGMP Snooping
- 40.3 Configure IGMP Filter
- 40.4 Enabling STP
- 40.5 no Command Examples
- 40.5.1 Disable Commands
- 40.5.2 Resetting Commands
- 40.5.3 Re-enable commands
- 40.5.4 Other Examples of no Commands
- 40.6 Static Route Commands
- 40.7 Enabling MAC Filtering
- 40.8 Enabling Trunking
- 40.9 Enabling Port Authentication
- 40.9.1 RADIUS Server Settings
- 40.9.2 Port Authentication Settings
- Interface Commands
- 41.1 Overview
- 41.2 Interface Command Examples
- 41.2.1 interface port-channel
- 41.2.2 bpdu-control
- 41.2.3 broadcast-limit
- 41.2.4 bandwidth-limit
- 41.2.5 mirror
- 41.2.6 gvrp
- 41.2.7 ingress-check
- 41.2.8 frame-type
- 41.2.9 weight
- 41.2.10 egress set
- 41.2.11 qos priority
- 41.2.12 name
- 41.2.13 speed-duplex
- 41.2.14 test
- 41.3 Interface no Command Examples
- 41.3.1 no bandwidth-limit
- IEEE 802.1Q Tagged VLAN Commands
- 42.1 Configuring Tagged VLAN
- 42.2 Global VLAN1Q Tagged VLAN Configuration Commands
- 42.2.1 GARP Status
- 42.2.2 GARP Timer
- 42.2.3 GVRP Timer
- 42.2.4 Enable GVRP
- 42.2.5 Disable GVRP
- 42.3 Port VLAN Commands
- 42.3.1 Set Port VID
- 42.3.2 Set Acceptable Frame Type
- 42.3.3 Enable or Disable Port GVRP
- 42.3.4 Modify Static VLAN
- 42.3.5 Delete VLAN ID
- 42.4 Enable VLAN
- 42.5 Disable VLAN
- 42.6 Show VLAN Setting
- Multicast VLAN Registration Commands
- Routing Domain Command Examples
- Troubleshooting
- Introducing Commands
- Appendices and Index
GS-2724 User’s Guide
223
CHAPTER 36
Routing Table
This chapter introduces the routing table.
36.1 Overview
The routing table contains the route information to the network(s) that the Switch can reach.
The Switch automatically updates the routing table with the RIP information received from
other Ethernet devices.
36.2 Viewing the Routing Table
Use this screen to view routing table information. Click Management > Routing Table in the
navigation panel to display the screen as shown.
Figure 122 Routing Table Status
The following table describes the labels in this screen.
Table 85 Routing Table Status
LABEL DESCRIPTION
Index This field displays the index number.
Destination This field displays the destination IP routing domain.
Gateway This field displays the IP address of the gateway device.
Interface This field displays the IP address of the Interface.
Metric This field displays the cost of the route.
Type This field displays the method used to learn the route.