User`s guide
Table Of Contents
- User’s Guide
- Introduction and Hardware
- Basic Configuration
- Advanced
- VLAN
- Static MAC Forward Setup
- Filtering
- Spanning Tree Protocol
- 11.1 STP/RSTP Overview
- 11.1.1 STP Terminology
- 11.1.2 How STP Works
- 11.1.3 STP Port States
- 11.1.4 Multiple RSTP
- 11.2 Spanning Tree Protocol Main Screen
- 11.3 Configure Rapid Spanning Tree Protocol
- 11.4 Rapid Spanning Tree Protocol Status
- 11.5 Configure Multiple Rapid Spanning Tree Protocol
- 11.6 Multiple Rapid Spanning Tree Protocol Status
- Bandwidth Control
- Broadcast Storm Control
- Mirroring
- Link Aggregation
- Port Authentication
- Port Security
- Classifier
- Policy Rule
- Queuing Method
- VLAN Stacking
- Multicast
- 22.1 Multicast Overview
- 22.1.1 IP Multicast Addresses
- 22.1.2 IGMP Filtering
- 22.1.3 IGMP Snooping
- 22.2 Multicast Status
- 22.3 Multicast Setting
- 22.4 IGMP Filtering Profile
- 22.5 MVR Overview
- 22.5.1 Types of MVR Ports
- 22.5.2 MVR Modes
- 22.5.3 How MVR Works
- 22.6 General MVR Configuration
- 22.7 MVR Group Configuration
- 22.7.1 MVR Configuration Example
- IP Application
- Management
- Maintenance
- 28.1 The Maintenance Screen
- 28.2 Firmware Upgrade
- 28.3 Restore a Configuration File
- 28.4 Backup a Configuration File
- 28.5 Load Factory Default
- 28.6 Save Configuration
- 28.7 Reboot System
- 28.8 FTP Command Line
- 28.8.1 Filename Conventions
- 28.8.2 FTP Command Line Procedure
- 28.8.3 GUI-based FTP Clients
- 28.8.4 FTP Restrictions
- Access Control
- 29.1 Access Control Overview
- 29.2 The Access Control Main Screen
- 29.3 About SNMP
- 29.3.1 Supported MIBs
- 29.3.2 SNMP Traps
- 29.3.3 Configuring SNMP
- 29.4 SSH Overview
- 29.5 How SSH works
- 29.6 SSH Implementation on the Switch
- 29.6.1 Requirements for Using SSH
- 29.7 Introduction to HTTPS
- 29.8 HTTPS Example
- 29.8.1 Internet Explorer Warning Messages
- 29.8.2 Netscape Navigator Warning Messages
- 29.8.3 The Main Screen
- 29.9 Service Port Access Control
- 29.10 Remote Management
- Diagnostic
- Syslog
- Cluster Management
- MAC Table
- IP Table
- ARP Table
- Routing Table
- Configure Clone
- Maintenance
- CLI and Troubleshooting
- Introducing Commands
- 38.1 Overview
- 38.2 Accessing the CLI
- 38.2.1 The Console Port
- 38.3 The Login Screen
- 38.4 Command Syntax Conventions
- 38.5 Changing the Password
- 38.6 Privilege Levels
- 38.7 Command Modes
- 38.8 Getting Help
- 38.8.1 List of Available Commands
- 38.9 Using Command History
- 38.10 Saving Your Configuration
- 38.10.1 Configuration File
- 38.10.2 Logging Out
- 38.11 Command Summary
- 38.11.1 User Mode
- 38.11.2 Enable Mode
- 38.11.3 General Configuration Mode
- 38.11.4 interface port-channel Commands
- 38.11.5 interface route-domain Commands
- 38.11.6 config-vlan Commands
- 38.12 mvr Commands
- User and Enable Mode Commands
- 39.1 Overview
- 39.2 show Commands
- 39.2.1 show system-information
- 39.2.2 show ip
- 39.2.3 show logging
- 39.2.4 show interface
- 39.2.5 show mac address-table
- 39.3 ping
- 39.4 traceroute
- 39.5 Copy Port Attributes
- 39.6 Configuration File Maintenance
- 39.6.1 Using a Different Configuration File
- 39.6.2 Resetting to the Factory Default
- Configuration Mode Commands
- 40.1 Change the Out of Band Management IP Address
- 40.2 Enabling IGMP Snooping
- 40.3 Configure IGMP Filter
- 40.4 Enabling STP
- 40.5 no Command Examples
- 40.5.1 Disable Commands
- 40.5.2 Resetting Commands
- 40.5.3 Re-enable commands
- 40.5.4 Other Examples of no Commands
- 40.6 Static Route Commands
- 40.7 Enabling MAC Filtering
- 40.8 Enabling Trunking
- 40.9 Enabling Port Authentication
- 40.9.1 RADIUS Server Settings
- 40.9.2 Port Authentication Settings
- Interface Commands
- 41.1 Overview
- 41.2 Interface Command Examples
- 41.2.1 interface port-channel
- 41.2.2 bpdu-control
- 41.2.3 broadcast-limit
- 41.2.4 bandwidth-limit
- 41.2.5 mirror
- 41.2.6 gvrp
- 41.2.7 ingress-check
- 41.2.8 frame-type
- 41.2.9 weight
- 41.2.10 egress set
- 41.2.11 qos priority
- 41.2.12 name
- 41.2.13 speed-duplex
- 41.2.14 test
- 41.3 Interface no Command Examples
- 41.3.1 no bandwidth-limit
- IEEE 802.1Q Tagged VLAN Commands
- 42.1 Configuring Tagged VLAN
- 42.2 Global VLAN1Q Tagged VLAN Configuration Commands
- 42.2.1 GARP Status
- 42.2.2 GARP Timer
- 42.2.3 GVRP Timer
- 42.2.4 Enable GVRP
- 42.2.5 Disable GVRP
- 42.3 Port VLAN Commands
- 42.3.1 Set Port VID
- 42.3.2 Set Acceptable Frame Type
- 42.3.3 Enable or Disable Port GVRP
- 42.3.4 Modify Static VLAN
- 42.3.5 Delete VLAN ID
- 42.4 Enable VLAN
- 42.5 Disable VLAN
- 42.6 Show VLAN Setting
- Multicast VLAN Registration Commands
- Routing Domain Command Examples
- Troubleshooting
- Introducing Commands
- Appendices and Index
Chapter 16 Port Authentication
GS-2724 User’s Guide
123
16.2 Port Authentication Configuration
To enable port authentication, first activate IEEE802.1x security (both on the Switch and the
port(s)) then configure the RADIUS server settings.
Click Advanced Application > Port Authentication in the navigation panel to display the
screen as shown.
Figure 52 Port Authentication
16.2.1 Configuring RADIUS Server Settings
Use this screen to configure your RADIUS server settings. See Section 16.1.1 on page 121 for
more information on RADIUS servers. From the Port Authentication screen, click RADIUS
to display the configuration screen as shown.
Figure 53 RADIUS
The following table describes the labels in this screen.
Table 37 RADIUS
LABEL DESCRIPTION
Authentication Server
IP Address Enter the IP address of the external RADIUS server in dotted decimal notation.
UDP Port The default port of the RADIUS server for authentication is 1812. You need not
change this value unless your network administrator instructs you to do so.
Shared Secret Specify a password (up to 32 alphanumeric characters) as the key to be shared
between the external RADIUS server and the Switch. This key is not sent over the
network. This key must be the same on the external RADIUS server and the Switch.
Apply Click Apply to save your changes to the Switch’s run-time memory. The Switch
loses these changes if it is turned off or loses power, so use the Save link on the top
navigation panel to save your changes to the non-volatile memory when you are
done configuring.
Cancel Click Cancel to reset the fields.