NetAtlas Enterprise 1.00 Element Management System User’s Guide Version 1.
NetAtlas Enterprise 1.00 User’s Guide Copyright Copyright © 2005 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation.
NetAtlas Enterprise 1.00 User’s Guide Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
NetAtlas Enterprise 1.00 User’s Guide Safety Warnings For your safety, be sure to read and follow all warning notices and instructions. • To reduce the risk of fire, use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord. • Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel can service the device. Please contact your vendor for further information.
NetAtlas Enterprise 1.00 User’s Guide ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase.
NetAtlas Enterprise 1.00 User’s Guide Customer Support Please have the following information ready when you contact customer support. • • • • Product model and serial number. Warranty Information. Date that you received your device. Brief description of the problem and the steps you took to solve it. TELEPHONEA WEB SITE SALES E-MAIL FAX FTP SITE support@zyxel.com.tw +886-3-578-3942 sales@zyxel.com.tw +886-3-578-2439 www.zyxel.com ZyXEL Communications Corp. www.europe.zyxel.
NetAtlas Enterprise 1.00 User’s Guide TELEPHONEA WEB SITE SALES E-MAIL FAX FTP SITE support@zyxel.co.uk +44 (0) 1344 303044 08707 555779 (UK only) www.zyxel.co.uk sales@zyxel.co.uk +44 (0) 1344 303034 ftp.zyxel.co.uk METHOD SUPPORT E-MAIL REGULAR MAIL LOCATION UNITED KINGDOM ZyXEL Communications UK Ltd.,11 The Courtyard, Eastern Road, Bracknell, Berkshire, RG12 2XB, United Kingdom (UK) a. “+” is the (prefix) number you enter to make an international telephone call.
NetAtlas Enterprise 1.00 User’s Guide Table of Contents Copyright .................................................................................................................. 2 Federal Communications Commission (FCC) Interference Statement ............... 3 Safety Warnings ....................................................................................................... 4 ZyXEL Limited Warranty..........................................................................................
NetAtlas Enterprise 1.00 User’s Guide 2.5 Menu Shortcut Buttons .......................................................................................46 2.6 EMS Main Menu Summary ................................................................................46 2.7 Common EMS Command Buttons .....................................................................48 2.8 View the Switch ..................................................................................................48 2.9 Switch Information ..
NetAtlas Enterprise 1.00 User’s Guide 6.2 Loopback Test ....................................................................................................73 Chapter 7 Maintenance ........................................................................................................... 76 7.1 Firmware Upgrade .............................................................................................76 7.1.1 Procedure to Update Firmware .................................................................
NetAtlas Enterprise 1.00 User’s Guide 11.3 Priority Queue ................................................................................................100 11.3.1 Strictly Priority .......................................................................................100 11.3.2 Weighted Fair Scheduling .....................................................................101 11.3.3 Configuring Priority Queue ....................................................................101 11.4 STP Configuration ....
NetAtlas Enterprise 1.00 User’s Guide 13.2 Port VLAN ......................................................................................................126 13.2.1 Configuring Port VLAN .........................................................................126 13.3 Port Link Aggregation .....................................................................................127 13.3.1 Configuring Port Link Aggregation ........................................................128 13.4 Port STP ................
NetAtlas Enterprise 1.00 User’s Guide 15.3.2 Chart Format Display Variable ..............................................................154 15.3.3 Graph Labels ........................................................................................155 Chapter 16 Troubleshooting ................................................................................................... 158 16.1 General Installation Problems ........................................................................158 16.
NetAtlas Enterprise 1.00 User’s Guide List of Figures Figure 1 Installing MySQL: Welcome .................................................................................. 23 Figure 2 Installing MySQL: Information ............................................................................... 24 Figure 3 Installing MySQL: Choose Destination Location ................................................... 24 Figure 4 Installing MySQL: Setup Type ..................................................................
NetAtlas Enterprise 1.00 User’s Guide Figure 39 Configuration: Switch System Configuration ....................................................... 49 Figure 40 Configuration: Save ............................................................................................ 50 Figure 41 Submaps and Device Mapping ........................................................................... 52 Figure 42 Map: Add Submap/Device ..................................................................................
NetAtlas Enterprise 1.00 User’s Guide Figure 82 Configuration: Switch Configuration: MAC Forwarding: Add .............................. 112 Figure 83 Configuration: Switch Configuration: Filtering ..................................................... 113 Figure 84 Configuration: Switch Configuration: Filtering: Add ............................................ 114 Figure 85 Selecting a VLAN Type .......................................................................................
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide List of Tables Table 1 System Requirements ........................................................................................... 22 Table 2 Map Object Properties: General ............................................................................ 36 Table 3 Required Map Object Properties ........................................................................... 37 Table 4 EMS Main Screen Overview .................................................................
NetAtlas Enterprise 1.00 User’s Guide Table 39 Configuration: Switch Configuration: RADIUS ..................................................... 109 Table 40 Configuration: Switch Configuration: MAC Forwarding ....................................... 111 Table 41 Configuration: Switch Configuration: MAC Forwarding: Add ............................... 112 Table 42 Configuration: Switch Configuration: Filtering .....................................................
NetAtlas Enterprise 1.00 User’s Guide Preface Congratulations on your purchase of the NetAtlas Enterprise 1.00 Element Management System (EMS) for the ES-3124 Series. Note: Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. About This User's Guide This manual is designed to guide you through the configuration of your EMS for its applications.
NetAtlas Enterprise 1.00 User’s Guide User Guide Feedback Help us help you. E-mail all User Guide-related comments, questions or suggestions for improvement to techwriters@zyxel.com.tw or send regular mail to The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 300, Taiwan. Thank you.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 1 Introducing the EMS 1.1 EMS Overview The Element Management System (EMS) retrieves management information from switches using SNMP protocol. An EMS is composed of Network Elements (NE) that represent resources in a Network Management System (NMS). The network elements can represent a physical piece of equipment on the network, the components of a device on the network, or parts of the network itself.
NetAtlas Enterprise 1.00 User’s Guide 1.3 EMS Installation Overview The following steps give an overview of what you need to do to install the EMS: 1 Install SNMPc 2 Install MySQL 3 Install the EMS software. Install the MySQL driver during the EMS installation. 4 Add custom MIB files in SNMPc 5 Locate device(s) that you want the EMS to manage 6 Configure the MySQL ODBC driver to connect to MySQL database. 1.3.1 Installing the EMS Follow the steps below to install the EMS server on a computer.
NetAtlas Enterprise 1.00 User’s Guide Figure 2 Installing MySQL: Information 7 Click Browse if you want to install MySQL to a destination folder other than the destination shown. Figure 3 Installing MySQL: Choose Destination Location 8 You must select a setup type to install MySQL. Select Typical and click Next to continue.
NetAtlas Enterprise 1.00 User’s Guide Figure 4 Installing MySQL: Setup Type 9 Click Finish to complete the MySQL installation. Figure 5 Installing MySQL: Setup Complete 10 You must restart Windows to activate MySQL. 11 Find and double-click NetAtlasEnterprise_S100.exe on your EMS CD. 12 A Welcome screen displays. Click Next to continue.
NetAtlas Enterprise 1.00 User’s Guide Figure 6 Installing EMS: Welcome 13 Read the license agreement. Click Yes to accept the agreement. Figure 7 Installing EMS: License Agreement 14 Type your name, company name and product serial number in the following screen. Click Next to continue.
NetAtlas Enterprise 1.00 User’s Guide Figure 8 Installing EMS: Customer Information 15 You must select the same directory where you installed SNMPc. Click Browse if it’s different from the destination folder shown. Figure 9 Installing EMS: Choose Destination Location 16 You must select the directory where you installed MySQL. Click Browse if you did not install MySQL database in the default folder shown. Click Next.
NetAtlas Enterprise 1.00 User’s Guide Figure 10 Installing EMS: Specify MySQL Directory 17 In the next screen, click Next to begin the installation and start copying files. Figure 11 Installing EMS: Start Copying Files 18 When a Welcome screen displays. Click Next to install the MySQL ODBC driver.
NetAtlas Enterprise 1.00 User’s Guide Figure 12 Installing EMS: MySQL ODBC: Welcome 19 Read the license agreement. Click Next to accept the agreement. Figure 13 Installing EMS: MySQL ODBC: License Agreement 20 Click Next again to begin the MySQL ODBC driver installation.
NetAtlas Enterprise 1.00 User’s Guide Figure 14 Installing EMS: MySQL ODBC: Start Installing 21 Click Finish to complete the MySQL ODBC installation. Figure 15 Installing EMS: MySQL ODBC: Finish 22 In the final screen of the EMS wizard, click Finish to complete the EMS installation.
NetAtlas Enterprise 1.00 User’s Guide Figure 16 Installing EMS: Finish 1.4 SNMPc Network Manager Start the SNMPc Network Manager manually or have it start automatically each time you turn on your computer. 1.4.1 Manual SNMPc Startup Manually starting SNMPc depends on your operating system. In Windows 2000, click Start, Programs, SNMPc Network Manager, Startup System to start the SNMPc Network Manager. 1.4.
NetAtlas Enterprise 1.00 User’s Guide Figure 17 SNMPc Task Setup 1.5 Adding MIBs The Management Information Base (MIB) is designed for holding management information on systems such as the MSC that the standard MIB does not include. 1 From the SNMPc Network Manager main screen, click Config, MIB Database. Figure 18 Config: MIB Database 2 Click Add in the Compile Mibs screen.
NetAtlas Enterprise 1.00 User’s Guide Figure 19 Compile Mibs (First Screen) 3 Scroll down the Add Mibs dialog box and select the MIB: rfc2674.mib (P-BRIDGEMIB). Click OK. Figure 20 Add Mib Files 4 Click Compile in the Compile Mibs screen. Figure 21 Compile Mibs (Second Screen) 5 Click Yes when asked to confirm, then click OK.
NetAtlas Enterprise 1.00 User’s Guide Figure 22 Compile Mibs 6 Repeat Steps 2 to 5 for the following; • • • • • • rfc2925.mib (DISMAN-PING-MIB) rfc3291.mib (INET-ADRESS-MIB) rfc3621.mib (POWER-ETHERNET-MIB) zyxel.mib zyxel-es3124.mib zyxel-es3124pwr.mib. Note: You must add and compile the MIBs separately in the order specified. 7 Finally click Done in the Compile Mibs screen. 1.
NetAtlas Enterprise 1.00 User’s Guide Figure 24 Discovery Agents Screen 3 Find your device in the Device List panel. Double-click the device icon to access the EMS. 1.6.2 Add Device(s) Manually If you have disabled auto-discovery, follow the steps below to add your device(s) manually. 1 Click Insert, MAP Object, Device. Figure 25 Insert, MAP Object, Device 2 Fill in the MAP Object Properties screen and then click OK.
NetAtlas Enterprise 1.00 User’s Guide Figure 26 Map Object Properties: Generall Table 2 Map Object Properties: General FIELD DESCRIPTION Label Type a device name for identification purposes. If you do not configure this field, the default label is “New Object”. Type This field shows what type of device it is, for example a hub, workstation, router etc. This field displays Device for the switch. Address Type the IP address of the switch.
NetAtlas Enterprise 1.00 User’s Guide Figure 27 Map Object Properties 3 Follow the instructions in the table below to set the specified fields in the Map Object Properties screen. Table 3 Required Map Object Properties FIELD VALUE Read Access Mode “SNMPV2c” Read/Write Access Mode “SNMPV2c” Read Community field For initial configuration, “public” is the default for most devices. After initial configuration, you assign this field.
NetAtlas Enterprise 1.00 User’s Guide Figure 28 Network Manager Shortcuts 6 Make sure the MySQL database is running. You must restart windows after you install MySQL. MySQL should start automatically when you restart Windows. If it does not, click start, Programs, Startup and then click WinMySQLadmin.
NetAtlas Enterprise 1.00 User’s Guide Figure 29 Startup MySQL 1.8 Configuring MySQL ODBC Driver The MySQL driver should already be installed from the EMS installation. You must configure the MySQL ODBC driver for the EMS to connect to the MySQL database successfully. Follow the steps below to configure the ODBC driver in Windows XP. Steps may be similar for Windows NT4.0. Click Start, Settings and Control Panel to open the Control Panel screen. Double-click Administrative Tools.
NetAtlas Enterprise 1.00 User’s Guide Figure 30 Data Sources (ODBC) 2 Click the User DSN tab and select the switch MySQL driver from the User Data Sources list. 3 Click Configure. Figure 31 ODBC Data Source Administrator 4 The MySQL ODBC DSN Configuration screen displays as shown next. Specify your MySQL database settings and click OK.
NetAtlas Enterprise 1.00 User’s Guide Figure 32 MySQL: Connection Setup 5 Double-click the switch icon to view the Switch Manager. Figure 33 Switch Device List Icon 6 Double-click the Switch Manager icon.
NetAtlas Enterprise 1.00 User’s Guide Note: For information on the Window, Admin and Help options in the Switch Manager screen, see Section 14.2 on page 140. The EMS polls for all the available switch cards. Select a device icon to display a graphic of the switch in the Device Panel. You can only display one switch in the Device Panel at one time.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 2 EMS Main Window This chapter describes the EMS main window. 2.1 Introducing the EMS Main Window After you have logged into the EMS, double-click the switch device icon in the Device List Panel to display the EMS main screen (shown next). The EMS retrieves device information from the switch (using SNMP protocol).
NetAtlas Enterprise 1.00 User’s Guide The following table describes the elements in the EMS screen. Table 4 EMS Main Screen Overview ELEMENT FUNCTION Menu Shortcut Bar Use these buttons to execute common commands quickly. Hold the cursor over an icon to see a tool tip. Device Panel This is a graphical device display. Double-click on a switch to display the EMS GUI management window for the switch. Device List Panel View devices in a tree structure.
NetAtlas Enterprise 1.00 User’s Guide If an alarm turns on, click the Port Status tab in the System Message Panel or proceed to Section 5.1 on page 60 for hardware troubleshooting. 2.4 System Message Panel Port Status Proceed to Section 5.4 on page 66 for information on the details displayed in this screen. 2.5 Menu Shortcut Buttons The following is a brief overview of the menu shortcut buttons. Figure 37 EMS Main Screen Shortcut Bar 2.
NetAtlas Enterprise 1.00 User’s Guide The following table summarizes these sub-links in the navigation panel. Table 8 EMS Navigation Panel Sub-link Descriptions DESCRIPTION LABEL MAP Screens Add Submap/Device This link takes you to a screen where you can add a device or a submap folder to the EMS Device List Panel. Edit Node This link takes you to a screen where you can edit device properties. Search Node This link takes you to a screen where you can search for a device or a submap folder.
NetAtlas Enterprise 1.00 User’s Guide Table 8 EMS Navigation Panel Sub-link Descriptions (continued) DESCRIPTION LABEL Telnet This link takes you to a screen where you can access a device Telnet service. Web Access This link takes you to a screen where you can access a device Web configurator. Ping This link takes you to a screen where you can ping a device directly through the EMS. 2.7 Common EMS Command Buttons The following table shows common command buttons found on most EMS screens.
NetAtlas Enterprise 1.00 User’s Guide 3 Choose a switch from the list located on the left-hand side of the screen. Figure 39 Configuration: Switch System Configuration The following table describes the labels in this screen. Table 10 Configuration: Switch System Configuration 49 LABEL DESCRIPTION Device Name This field displays the selected switch name. Device IP This field displays the selected switch IP address. Name Enter a descriptive name for identification purposes.
NetAtlas Enterprise 1.00 User’s Guide Table 10 Configuration: Switch System Configuration (continued) LABEL DESCRIPTION Apply Click Apply to save the changes back to the switch. Close Click Close to close the screen. 2.10 Configuration Save You can save the current configuration of the switch(es). Note: Do not turn off the switch during the updating process, as it may corrupt the firmware and make your switch unusable.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 3 Managing Device Maps in EMS This chapter describes the Map menus you use to add, edit or delete device mappings in the EMS. 3.1 Submap and Device Mapping The EMS mapping displays logical hierarchy for the switch in the EMS. When you first start the EMS, the default Root Map and an icon for your switch device are created in the Device List Panel automatically. Both devices and submaps (or folders) can be added below the rootmap.
NetAtlas Enterprise 1.00 User’s Guide Figure 42 Map: Add Submap/Device The following table describes the labels in this screen. Table 11 Map: Add Submap/Device LABEL DESCRIPTION Properties Select the Submap or Device radio button to add a new submap or device icon to the Device List Panel. If you select Submap, only the Name and Description fields display ; all other fields appear as read-only. Name Enter a descriptive name (up to 32 characters) for this node for identification purposes.
NetAtlas Enterprise 1.00 User’s Guide Figure 43 Map: Edit Node Refer to Table 11 on page 53 for the field descriptions. 3.1.3 Find an Object To find or locate a device (or node), click Map and then Find Object. Figure 44 Map: Find Object Enter a descriptive text (for example, the node name) in the Find field and click OK to start the search. 3.1.4 Delete a Submap To delete a submap, select the submap icon in the Device List Panel and click Map and then Delete.
NetAtlas Enterprise 1.00 User’s Guide Figure 45 Map: Delete Warning Note: If you delete a submap, all devices under a submap will be removed. 3.1.5 Delete a Device To remove a device from the Device List Panel, select the device icon and click Map and then Delete. 3.2 Exit Click Map and then Exit to close the EMS screen.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 4 VLAN Template This chapter describes how to configure a VLAN template. 4.1 VLAN Template Overview A template is a pre-configured set of configuration settings. Templates allow you to configure device VLANs efficiently. The template can then be uploaded to one or more devices thus removing the need to configure the VLAN settings for each device. See the VLAN Configuration chapter for more information on the template upload. 4.1.
NetAtlas Enterprise 1.00 User’s Guide Figure 46 Template: VLAN The following table describes the labels in this screen. Table 12 Template: VLAN LABEL DESCRIPTION Device Type Select a device type from the drop-down list box to view the device’s VLAN configuration. VLAN Identity 57 VLAN ID Enter a unique number to identify the VLAN. VLAN Name Enter a descriptive name for identification purposes. Egress Ports A port that is in the egress list in a VLAN.
NetAtlas Enterprise 1.00 User’s Guide Table 12 Template: VLAN (continued) Chapter 4 LABEL DESCRIPTION Delete Click on a VLAN in the left-hand column of this screen and then click the Delete button to remove it from the VLAN template. Modify Click on a VLAN in the left-hand column of this screen. Change the VLAN Name or change the configuration of the egress, forbidden and untagged ports. Click the Modify button to save the changes to the switch.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 5 Status This chapter covers the hardware status, STP status, VLAN status, port status and 802.1d status screens. 5.1 Hardware Status Follow the steps below to view fan speeds, voltage levels and temperatures of a switch. 1 To view the hardware status of a switch, click Status and then Hardware Status. 2 Choose a switch from the list located on the left-hand side of the screen as shown next. It may take a few seconds to update the screen.
NetAtlas Enterprise 1.00 User’s Guide Figure 47 Status: Hardware Status The following table describes the labels in this screen. Table 13 Status: Hardware Status 61 LABEL DESCRIPTION Fan RPM A properly functioning fan is an essential component (along with a sufficiently ventilated, cool operating environment) in order for the device to stay within the temperature threshold. Each fan has a sensor that is capable of detecting and reporting if the fan speed falls below the threshold shown.
NetAtlas Enterprise 1.00 User’s Guide Table 13 Status: Hardware Status (continued) LABEL DESCRIPTION Min This field displays the minimum voltage recorded at this sensor in volts. Threshold This field displays the minimum voltage percentage at which the switch should work. Status NORMAL indicates that the voltage is within an acceptable operating range at this point; otherwise ERROR is displayed. ABSENT indicates that there is no power reading at a sensor(s).
NetAtlas Enterprise 1.00 User’s Guide Path cost is the cost of transmitting a frame onto a LAN through that port. It is assigned according to the speed of the link to which a port is attached. The slower the media, the higher the cost - see the next table.
NetAtlas Enterprise 1.00 User’s Guide 5.2.3 STP Port States STP assigns five port states (see next table) to eliminate packet looping. A bridge port is not allowed to go directly from blocking state to forwarding state so as to eliminate transient loops. Table 15 STP Port States PORT STATE DESCRIPTION Disabled STP is disabled (default). Blocking Only configuration and management BPDUs are received and processed. Listening All BPDUs are received and processed.
NetAtlas Enterprise 1.00 User’s Guide Table 16 Status: STP Status (continued) LABEL DESCRIPTION Hello Time (second) This is the time interval (in seconds) at which the root device transmits a configuration message. The root bridge determines Hello Time, Max Age and Forwarding Delay Max Age (second) This is the maximum time (in seconds) a switch can wait without receiving a configuration message before attempting to reconfigure.
NetAtlas Enterprise 1.00 User’s Guide Figure 49 Status: VLAN Status The following table describes the labels in this screen. Table 17 Status: VLAN Status LABEL DESCRIPTION VLAN ID This field displays the identification number of the VLAN. Name This field displays a unique number for identification purposes. Elapsed Time This field displays the time since the VLAN was created. Status This field displays Active if the VLAN is active and will remain so after the next reset of the device.
NetAtlas Enterprise 1.00 User’s Guide 2 To view the port status of a switch choose a switch from the list located on the left-hand side of the screen. Figure 50 Status: Port Status The following table describes the labels in this screen. Table 18 Status: Port Status 67 LABEL DESCRIPTION Port This identifies the Ethernet port. Link Speed This field displays the speed (either 10M for 10Mbps, 100M for 100Mbps or 1000M for 1000Mbps) and the duplex (F for full duplex or H for half).
NetAtlas Enterprise 1.00 User’s Guide 5.5 802.1D Use the following screens to view a table of MAC address entries or to view a table of IP address mappings. 5.5.1 802.1D: MAC Table The MAC table shows how frames are forwarded or filtered across the switch’s ports. It shows what device MAC address, belonging to what VLAN group (if any) is forwarded to which port(s) and whether the MAC address is dynamic (learned by the switch) or static (manually entered in Static MAC Forwarding).
NetAtlas Enterprise 1.00 User’s Guide 1 Click Status and then 802.1d. 2 To view the MAC table of a switch choose a switch from the list located on the left-hand side of the screen and click the MAC Table tab. Figure 52 Status: 802.1d: MAC Table The following table describes the labels in this screen. Table 19 Status: 802.1d: MAC Table 69 LABEL DESCRIPTION Sort by Click one of the following buttons to display and arrange the data according to that button type.
NetAtlas Enterprise 1.00 User’s Guide 5.5.3 802.1D: ARP Table Address Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address, also known as a Media Access Control or MAC address, on the local area network. An IP (version 4) address is 32 bits long. In an Ethernet LAN, MAC addresses are 48 bits long. The ARP Table maintains an association between each MAC address and its corresponding IP address. 5.5.
NetAtlas Enterprise 1.00 User’s Guide Figure 53 Status: 802.1d: ARP Table The following table describes the labels in this screen. Table 20 Status: 802.1d: ARP Table 71 LABEL DESCRIPTION Index This is the ARP table entry number. IP Address This is the learned IP address of a device connected to a switch port with corresponding MAC address below. MAC Address This is the MAC address of the device with corresponding IP address above.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 6 Fault Menus This chapter describes the event logs and how to perform loopback tests. 6.1 Event Log To display system event logs click Fault and then Event Log to view the following screen. Figure 54 Fault: Event Log The following table describes the labels in this screen. Table 21 Fault: Event Log LABEL DESCRIPTION Alarm Filter Port Chapter 6 Fault Menus To display event logs of a port, select the port from the drop-down list box.
NetAtlas Enterprise 1.00 User’s Guide Table 21 Fault: Event Log (continued) LABEL DESCRIPTION Alarm Type Select the type of logs from the drop-down list box. Choices are All, Communication, QualityOfService, ProcessingError, Equipment and Environmental. Select All for system event logs generated by all alarm types. Select Communication for transmission and signal logs. Select QualityOfService for performance logs. Select Processing Error for software and configuration problem logs.
NetAtlas Enterprise 1.00 User’s Guide 2 Choose a switch from the list located on the left-hand side of the screen. 3 Choose a port from the list located on the right-hand side of the screen. 4 Click Apply to start the loopback test.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 7 Maintenance This chapter tells you how to backup and restore your configuration file as well as upload new firmware and configuration files. 7.1 Firmware Upgrade You must be logged in with system administrator rights to use this function. Note: Do not turn off the switch during the updating process, as it may corrupt the firmware and make the selected switch unusable. 7.1.
NetAtlas Enterprise 1.00 User’s Guide Figure 56 Maintenance: Firmware Upgrade The switch(es) automatically restarts when the firmware upload is complete. 7.2 Device Reset Reboot System allows you to restart a switch without physically turning the power off. Select a device from the list and click Apply. Click Apply again and then wait for the switch to restart. This takes up to two minutes. This does not affect the switch’s configuration.
NetAtlas Enterprise 1.00 User’s Guide Figure 57 Maintenance: Device Reset 7.3 Network Element Configuration Backup and Restore A Network Element is a piece of telecommunications equipment that provides support or services to the user. Follow the steps below to backup or restore a switch configuration file. 1 Click Maintenance and then NE (Network Element) Configuration Backup and Restore. 2 Select a switch from the drop-down list box.
NetAtlas Enterprise 1.00 User’s Guide Figure 58 Maintenance: Configuration Backup/Restore The following table describes the labels in this screen. Table 22 Maintenance: Configuration Backup/Restore LABEL DESCRIPTION Directory/File Name Type the path and file name of the configuration file you wish to restore to the switch or backup to your computer in the Directory / File Name text box or click Browse to locate it.
NetAtlas Enterprise 1.00 User’s Guide Figure 59 Maintenance: Load factory Defaults 7.5 Scheduled Network Element Configuration Backup Perform configuration backups according to a schedule. Set the frequency, time and date of the backup and the location where you want to backup the configuration file.
NetAtlas Enterprise 1.00 User’s Guide Figure 60 Maintenance: Scheduled NE Config Backup The following table describes the labels in this screen. Table 23 Maintenance: Scheduled NE Config Backup LABEL DESCRIPTION Backup Schedule Frequency Scheduled backups can be performed on a Daily, Weekly or Monthly basis. Select a radio button to schedule configuration backups starting at the date and time specifed below. The default setting is No Backup.
NetAtlas Enterprise 1.00 User’s Guide 1 Click the Add button in the Scheduled NE Config Backup screen. 2 Click the OK button. Figure 61 Maintenance: Scheduled NE Config Backup Add 7.5.2 Scheduled Network Element Configuration Backup Remove To remove a device from the Scheduled NE Configuration Backup screen, click the Remove button in the Scheduled NE Config Backup screen.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 8 Tools This chapter shows you how to access a switch via Telnet or web configurator directly through the EMS. You may need to do this to test the switch network connection for example. 8.1 Accessing the switch Access the switch remotely via Telnet or web browser. Note: When you access a switch via Telnet or the web configurator, you CANNOT make any changes to that switch using the EMS. 8.1.
NetAtlas Enterprise 1.00 User’s Guide 2 Click Tool and then Web Access to open the switch web configurator password screen. From here you can log in directly to the switch. 3 Type the switch User name and Password to access the web configurator. Figure 63 Web Access 4 Refer to the switch User’s Guide for information on the web configurator main screen. 8.2 Ping Ping the host to see if the links and TCP/IP protocol on both your computer and the switch is working.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 9 Device Menu Overview This chapter introduces the device configuration menus. 9.1 Device Menu Summary To select a device configuration menu, right-click on a device in the Device List Panel. Figure 65 Device Panel List Menus The following table shows the menus, sub menus and menu tab names. Table 24 Device Menu Summary MENU SUBMENU SUBMENU TABS Property Edit Device Configuration System Configuration System Info SNMP Conf. Remote Mgmt.
NetAtlas Enterprise 1.00 User’s Guide Table 24 Device Menu Summary MENU SUBMENU SUBMENU TABS Filtering VLAN Configuration Ethernet Port Configuration Port Setup Port VLAN Port Link Aggregation Port STP Bandwidth Ctrl. Broadcast Storm Ctrl. Queue Method Port 802.1x Port Security Port Mirroring VLAN Stacking Routing Configuration Static Route Configuration Save Configuration 9.2 Property Configuration See Section 3.1.2 on page 53 for information on the Edit Device screen. 9.
NetAtlas Enterprise 1.00 User’s Guide Figure 66 Configuration Window Panels Device Panel Port List Panel Switch Configurator Panel The following table describes the elements in this screen. Table 25 Configuration Window Panels LABEL DESCRIPTION Device Panel This panel displays all active devices currently managed by the EMS. Port List Panel This field displays a list of switch ports. This list displays in the Ethernet Port Configuration screens only.
NetAtlas Enterprise 1.00 User’s Guide Figure 67 Applied Results 3 Click Done to close the screen. 9.3.2 Copy to.. Button The Copy to.. button allows you to copy the configuration from the switch you are currently configuring to one or more switches. 1 In the Device Panel list, select a device that you want configure. 2 Select a tab in the Switch Configurator Panel. 3 Select a port or multiple ports (by pressing the [CTRL] key and clicking at the same time) from the Port List Panel.
NetAtlas Enterprise 1.00 User’s Guide Figure 68 Copy Port Screen Device List Panel Port List Panel Copy Port List Panel The following table describes the labels in this screen. Table 26 Copy Port Screen LABEL DESCRIPTION Device List Select a device to which you want to copy from the switch you are currently configuring. Port List Panel Select one port or multiple ports (by pressing the [CTRL] key and clicking at the same time) from the Port List Panel .
NetAtlas Enterprise 1.00 User’s Guide Figure 69 Copy Successful 8 Click Done to close the screen.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 10 System Configuration This chapter shows you how to view general system information, configure SNMP, remote management and time setup. 10.1 System Info See Section 2.9 on page 48 for information about the switch. 10.2 SNMP This explains explains SNMP configuration. 10.2.1 About SNMP Simple Network Management Protocol is a protocol used for exchanging management information between network switches. SNMP is a member of TCP/IP protocol suite.
NetAtlas Enterprise 1.00 User’s Guide An agent is a management software module that resides in a managed switch (the ES-3124). An agent translates the local management information from the managed switch into a form compatible with SNMP. The manager is the console through which network administrators perform network management functions. It executes applications that control and monitor managed devices.
NetAtlas Enterprise 1.00 User’s Guide Figure 71 Configuration: System Configuration: SNMP Conf. The following table describes the labels in this screen. Table 28 Configuration: System Configuration: SNMP Conf. LABEL DESCRIPTION Get Community Enter the get community, which is the password for the incoming Get- and GetNext- requests from the management station. Set Community Enter the set community, which is the password for incoming Set- requests from the management station.
NetAtlas Enterprise 1.00 User’s Guide Figure 72 Configuration: System Configuration: Remote Management The following table describes the labels in this screen. Table 29 Configuration: System Configuration: Remote Management 95 LABEL DESCRIPTION Services This panel displays the services that you may use to remotely manage the switch. Select the check box(es) to allow remote management using the service(s). Port Enter the number of the server port to use with the corresponding service.
NetAtlas Enterprise 1.00 User’s Guide Table 29 Configuration: System Configuration: Remote Management (continued) LABEL DESCRIPTION Telnet, FTP, HTTP, ICMP, SNMP, ICMP, SSH, HTTPS Select the checkbox to allow the trusted computer(s) in the IP address range specified above to use this service to manage the switch. Apply Click Apply to save the changes back to the switch. 10.4 Time Setup The EMS keeps track of the time and date.
NetAtlas Enterprise 1.00 User’s Guide Figure 73 Configuration: System Configuration: Time Setup The following table describes the labels in this screen. Table 30 Configuration: System Configuration: Time Setup 97 LABEL DESCRIPTION Use Time Server When Select the time service protocol that your time server sends when you start the EMS. Not all time servers support all protocols, so you may have to check with your ISP/network administrator or use trial and error to find a protocol that works.
NetAtlas Enterprise 1.00 User’s Guide C H A P T E R 11 Switch Configuration This chapter shows how to configure priority queuing, STP, link aggregation, DHCP relay, GARP timer and RADIUS. 11.1 IGMP Snooping IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group - it is not used to carry user data. Refer to RFC 1112 and RFC 2236 for information on IGMP versions 1 and 2 respectively.
NetAtlas Enterprise 1.00 User’s Guide Figure 74 Configuration: Switch Configuration: Switch Setup The following table describes the labels in this screen. Table 31 Configuration: Switch Configuration: Switch Setup LABEL DESCRIPTION VLAN Type Choose 802.1Q or Port Based from the drop-down list box. The VLAN Setup screen changes depending on whether you choose 802.1Q VLAN Type or Port Based VLAN Type in this screen. See Section 13.2 on page 126 and the VLAN chapter for more information on VLANs.
NetAtlas Enterprise 1.00 User’s Guide Table 31 Configuration: Switch Configuration: Switch Setup (continued) LABEL DESCRIPTION IGMP Snooping Select the check box to enable IGMP snooping. See Section 11.1 on page 98 for more information on IGMP snooping. Bridge control protocol transparency Select the check box to allow the switch to handle bridging control protocols (STP for example). You also need to define how to treat a BPDU in the Port Setup screen.
NetAtlas Enterprise 1.00 User’s Guide 11.3.2 Weighted Fair Scheduling Weighted Fair Scheduling is used to guarantee each queue’s minimum bandwidth based on their bandwidth weight (portion) when there is traffic congestion. WFS is activated only when a port has more traffic than it can handle. Queues with larger weights get more guaranteed bandwidth than queues with smaller weights. This queuing mechanism is highly efficient in that it divides any available bandwidth across the different traffic queues.
NetAtlas Enterprise 1.00 User’s Guide The following table describes the labels in this screen. Table 32 Configuration: Switch Configuration: Priority Queue LABELS DESCRIPTION Priority Queue Assignment IEEE 802.1p defines up to 8 separate traffic types by inserting a tag into a MAC-layer frame that contains bits to define class of service. Frames without an explicit priority tag are given the default priority of the ingress port. Use these fields to configure the priority level-to-physical queue mapping.
NetAtlas Enterprise 1.00 User’s Guide 11.5.1 Configuring STP Parameters 1 In the Device Panel list, select a device and then right-click. 2 Click Configuration, Switch Configuration and then the Switch Setup tab. 3 Select the STP Configuration check box and then click Apply. 4 Click Configuration, Switch Configuration and then the STP Conf. tab to display the following screen. Figure 76 Configuration: Switch Configuration: STP Conf. The following table describes the labels in this screen.
NetAtlas Enterprise 1.00 User’s Guide Table 33 Configuration: Switch Configuration: STP Conf. (continued) LABEL DESCRIPTION Forward Delay This is the maximum time (in seconds) a device will wait before changing states. This delay is required because every device must receive information about topology changes before it starts to forward frames.
NetAtlas Enterprise 1.00 User’s Guide 11.6.3 Link Aggregation ID LACP aggregation ID consists of the following information: Table 34 Aggregation ID Local Switch Local switch [(0000,00-00-00-00-00-00,0000,00,0000)] 0000 00-00-00-00-00 0000 00 0000 System priority MAC address Key Port Priority Port Number Table 35 Aggregation ID Peer Switch Peer switch [(0000,00-00-00-00-00-00,0000,00,0000)] 0000 00-00-00-00-00 0000 00 0000 System priority MAC address Key Port Priority Port Number 11.6.
NetAtlas Enterprise 1.00 User’s Guide The following table describes the labels in this screen. Table 36 Configuration: Switch Configuration: Link Aggregation TABLE DESCRIPTION LACP System Priority LACP system priority is a number between 0 and 65,355. The switch with the lowest system priority (and lowest port number if system priority is the same) becomes the LACP “server”. The LACP “server” controls the operation of LACP setup.
NetAtlas Enterprise 1.00 User’s Guide • System name (up to 32 bytes, this is optional) 11.7.3 Configuring DHCP Relay 1 In the Device Panel list, select a device and then right-click. 2 Click Configuration, Switch Configuration and then the Switch Setup tab. 3 Select the DHCP Relay check box and then click Apply. 4 Click Configuration, Switch Configuration and then the DHCP Relay tab to display the following screen.
NetAtlas Enterprise 1.00 User’s Guide 11.8 GARP Timer Switches join VLANs by making a declaration. A declaration is made by issuing a Join message using GARP. Declarations are withdrawn by issuing a Leave message. A Leave All message terminates all registrations. GARP timers set declaration timeout values. See the chapter on VLAN setup for more background information. 11.8.1 Configuring GARP Timer 1 In the Device Panel list, select a device and then right-click.
NetAtlas Enterprise 1.00 User’s Guide 11.9 RADIUS RADIUS (Remote Authentication Dial-In User Service) authentication is a popular protocol used to authenticate users by means of an external server instead of (or in addition to) an internal device user database that is limited to the memory capacity of the device. In essence, RADIUS authentication allows you to validate an unlimited number of users from a central location. 11.9.1 Introduction to Authentication IEEE 802.
NetAtlas Enterprise 1.00 User’s Guide Table 39 Configuration: Switch Configuration: RADIUS LABEL DESCRIPTION Shared Secret Specify a password (up to 31 alphanumeric characters) as the key to be shared between the external RADIUS server and the switch. This key is not sent over the network. This key must be the same on the external RADIUS server and the switch. Apply Click Apply to save your changes back to the switch. 11.10 MAC Forwarding This chapter discusses MAC address forwarding. 11.10.
NetAtlas Enterprise 1.00 User’s Guide Figure 81 Configuration: Switch Configuration: MAC Forwarding The following table describes the labels in this screen. Table 40 Configuration: Switch Configuration: MAC Forwarding LABEL DESCRIPTION Index Click an index number to modify a static MAC address rule for a port. Active This field displays whether this static MAC address forwarding rule is active (Yes) or not (No). You may temporarily deactivate a rule without deleting it.
NetAtlas Enterprise 1.00 User’s Guide Figure 82 Configuration: Switch Configuration: MAC Forwarding: Add The following table describes the labels in this screen.. Table 41 Configuration: Switch Configuration: MAC Forwarding: Add LABEL DESCRIPTION Active Select this check box to activate your rule. You may temporarily deactivate a rule without deleting it by clearing this check box. MAC Enter the MAC address in valid MAC address format, that is, six hexadecimal character pairs.
NetAtlas Enterprise 1.00 User’s Guide Figure 83 Configuration: Switch Configuration: Filtering The following table describes the labels in the summary table. Table 42 Configuration: Switch Configuration: Filtering LABEL DESCRIPTION Index This field displays the index number of the rule. Click an index number to edit the rule. Active This field displays Yes when the rule is activated and No when is it deactivated. Name This field displays the descriptive name for this rule.
NetAtlas Enterprise 1.00 User’s Guide Figure 84 Configuration: Switch Configuration: Filtering: Add The following table describes the labels in this screen.. Table 43 Configuration: Switch Configuration: Filtering: Add LABEL DESCRIPTION Active Select this check box to activate your rule. You may temporarily deactivate a rule without deleting it by clearing this check box. Name Type a descriptive name for this filter rule. This is for identification purpose only.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 12 VLAN This chapter describes how to view VLAN status, add and edit VLANs and how to use the VLAN template. The type of screen you see here depends on the VLAN Type you selected in the Switch Setup screen. 12.1 Introduction to VLANs A VLAN (Virtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Devices on a logical network belong to one group. A device can belong to more than one group.
NetAtlas Enterprise 1.00 User’s Guide Figure 85 Selecting a VLAN Type 4 Click Configuration and then VLAN Configuration to display the screen as shown next. Figure 86 Configuration: VLAN Configuration: 802.1Q The following table describes the labels in this screen. Table 44 Configuration: VLAN Configuration: 802.1Q 117 LABEL DESCRIPTION VLAN ID This field displays the ID of the VLAN. Name This field displays the name of the VLAN.
NetAtlas Enterprise 1.00 User’s Guide Table 44 Configuration: VLAN Configuration: 802.1Q (continued) LABEL DESCRIPTION New Click New to create a new VLAN. You must enter a VLAN ID and a VLAN Name to create a new VLAN. The new VLAN and name is displayed in the left-hand column in this screen. Delete Click on a VLAN in the left-hand column of this screen and then click the Delete button to remove it from the VLAN template. Modify Click on a VLAN in the left-hand column of this screen.
NetAtlas Enterprise 1.00 User’s Guide Figure 87 Configuration: VLAN Configuration: 802.1Q: Modify The following table describes the labels in this screen. Table 45 Configuration: VLAN Configuration: 802.1Q: Modify LABEL DESCRIPTION VLAN Identity Select the Active checkbox to enable this VLAN. VLAN ID This field displays a unique number to identify the VLAN. VLAN Name Enter a descriptive name for identification purposes.
NetAtlas Enterprise 1.00 User’s Guide The following table describes the labels in this screen for each VLAN port type. Table 46 VLAN Port Type Descriptions LABEL DESCRIPTION Egress Ports A port that is in the egress list in a VLAN. Only select this if the subscriber's DSL modem or router supports 802.1Q VLAN. Forbidden Ports A port that is blocked from joining a VLAN group. No frames are transmitted through this port. Untagged Ports A port that does not tag all outgoing frames transmitted.
NetAtlas Enterprise 1.00 User’s Guide Figure 88 Configuration: VLAN Configuration: Port Based The following table describes the labels in this screen. Table 47 Configuration: VLAN Configuration: Port Based 121 LABEL DESCRIPTION Setting Wizard Choose from All connected or Port isolation. All connected means all ports can communicate with each other, that is, there are no virtual LANs. All incoming and outgoing ports are selected. This option is the most flexible but also the least secure.
NetAtlas Enterprise 1.00 User’s Guide Table 47 Configuration: VLAN Configuration: Port Based (continued) LABEL DESCRIPTION Apply Click Apply to save the changes, including the “wizard settings”. Cancel Click Cancel to start configuring the screen again.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 13 Ethernet Port Configuration This chapter shows how to configure port setup, port VLAN, port link aggregation, port STP, bandwidth control, broadcast storm control, queuing method, port 802.1x, port security, port mirroring and VLAN stacking. 13.1 Port Setup Use the Port Setup screen to activate and configure switch port parameters. 13.1.1 Configuring Port Setup Follow the steps below to configure the Port Setup screen.
NetAtlas Enterprise 1.00 User’s Guide Figure 89 Configuration: Ethernet Port Configuration: Port Setup The following table describes the fields in this screen. Table 48 Configuration: Ethernet Port Configuration: Port Setup 125 LABEL DESCRIPTION Port Select a port index number from the list of ports on the device you want to configure. Active Select this check box to enable a port. The factory default for all ports is enabled. A port must be enabled for data transmission to occur.
NetAtlas Enterprise 1.00 User’s Guide Table 48 Configuration: Ethernet Port Configuration: Port Setup (continued) LABEL DESCRIPTION Flow Control A concentration of traffic on a port decreases port bandwidth and overflows buffer memory causing packet discards and frame losses. Flow Control is used to regulate transmission of signals to match the bandwidth of the receiving port. The switch uses IEEE802.3x flow control in full duplex mode and backpressure flow control in half duplex mode. IEEE802.
NetAtlas Enterprise 1.00 User’s Guide 5 Select the ports from the Port List Panel that you want to apply this configuration. Figure 90 Configuration: Ethernet Port Configuration: Port VLAN The following table describes the fields in this screen. Table 49 Configuration: Ethernet Port Configuration: Port VLAN LABEL DESCRIPTION Port Select a port index number from the list of ports on the device you want to configure.
NetAtlas Enterprise 1.00 User’s Guide 13.3.1 Configuring Port Link Aggregation Follow the steps below to configure the Port Link Aggregation screen. 1 In the Device Panel list, select a device and then right-click. 2 Click Configuration, Switch Configuration and then the Switch Setup tab. 3 Select the Link Aggregation check box and then click Apply. 4 Click Configuration, Ethernet Port Configuration and then the Port Link Aggregation tab.
NetAtlas Enterprise 1.00 User’s Guide 2 Click Configuration, Switch Configuration and then the Switch Setup tab. 3 Select the STP Configuration check box and then click Apply. 4 Click Configuration, Ethernet Port Configuration and then the Port STP tab. 5 Select the ports from the Port List Panel that you want to apply this configuration. Figure 92 Configuration: Ethernet Port Configuration: Port STP The following table describes the fields in this screen.
NetAtlas Enterprise 1.00 User’s Guide 3 Select the Bandwidth control check box and then click Apply. 4 Click Configuration, Ethernet Port Configuration and then the Bandwidth Ctrl. tab. 5 Select the ports from the Port List Panel that you want to apply this configuration. Figure 93 Configuration: Ethernet Port Configuration: Bandwidth Ctrl. The following table describes the fields in this screen. Table 52 Configuration: Ethernet Port Configuration: Bandwidth Ctrl.
NetAtlas Enterprise 1.00 User’s Guide 4 Click Configuration, Ethernet Port Configuration and then the Broadcast Storm Ctrl. tab. 5 Select the ports from the Port List Panel that you want to apply this configuration. Figure 94 Configuration: Ethernet Port Configuration: Broadcast Storm Ctrl. The following table describes the fields in this screen. Table 53 Configuration: Ethernet Port Configuration: Broadcast Storm Ctrl.
NetAtlas Enterprise 1.00 User’s Guide 5 Select the ports from the Port List Panel that you want to apply this configuration. Figure 95 Configuration: Ethernet Port Configuration: Queue Method The following table describes the fields in this screen. Table 54 Configuration: Ethernet Port Configuration: Queue Method LABEL DESCRIPTION Q0 ~ Q7 Strictly Priority services queues based on priority only. When the highest priority queue empties, traffic on the next highest-priority queue begins.
NetAtlas Enterprise 1.00 User’s Guide Figure 96 Configuration: Ethernet Port Configuration: Port 802.1x The following table describes the fields in this screen. Table 55 Configuration: Ethernet Port Configuration: Port 802.1x LABEL DESCRIPTION 802.1x Active Select this checkbox to permit 802.1x authentication on this port. You must first allow 802.1x authentication on the switch before configuring it on each port.
NetAtlas Enterprise 1.00 User’s Guide 2 Click Configuration, Switch Configuration and then the Switch Setup tab. 3 Select the Port Security check box and then click Apply. 4 Click Configuration, Ethernet Port Configuration and then the Port Security tab. Figure 97 Configuration: Ethernet Port Configuration: Port Security The following table describes the fields in this screen.
NetAtlas Enterprise 1.00 User’s Guide 13.10.1 Configuring Port Mirroring You must first select a monitor port. A monitor port is a port that copies the traffic of another port. After you select a monitor port, configure a mirroring rule in the related fields. Follow the steps below to configure the Port Mirroring screen. 1 In the Device Panel list, select a device and then right-click. 2 Click Configuration, Switch Configuration and then the Switch Setup tab.
NetAtlas Enterprise 1.00 User’s Guide A service provider’s customers may require a range of VLANs to handle multiple applications. A service provider’s customers can assign their own inner VLAN tags on ports for these applications. The service provider can assign an outer VLAN tag for each customer. Therefore, there is no VLAN tag overlap among customers, so traffic from different customers is kept separate. 13.11.2 Configuring VLAN Stacking Follow the steps below to configure the VLAN Stacking screen.
NetAtlas Enterprise 1.00 User’s Guide Table 58 Configuration: Ethernet Port Configuration: VLAN Stacking (continued) 137 TABLE DESCRIPTION Priority On the switch, configure priority level of inner IEEE 802.1Q tag in the Port Setup screen. "0" is the lowest priority level and "7" is the highest. Apply Click Apply to save the changes back to the switch.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 14 Routing Configuration This chapter shows you how to configure the routing functions. 14.1 Static Route Static routes tell the switch how to forward IP traffic when you configure the TCP/IP parameters manually. 14.1.1 Configuring Static Routing Follow the steps below to view the Routing Configuration screen. 1 In the Device Panel list, select a device and then right-click. 2 Click Configuration, Routing Configuration and then the tab.
NetAtlas Enterprise 1.00 User’s Guide The following table describes the labels in the summary table. Table 59 Configuration: Routing Configuration LABEL DESCRIPTION Index This field displays the index number of the route. Name This field displays the descriptive name for this route. This is for identification purpose only. Active This field displays Yes when the static route is activated and No when is it deactivated.
NetAtlas Enterprise 1.00 User’s Guide The following table describes the labels in this screen. Table 60 Configuration: Routing Configuration: Add or Modify LABEL DESCRIPTION Active This field allows you to activate/deactivate this static route. Name Enter a descriptive name for this route. This is for identification purpose only. Destination IP Address This parameter specifies the IP network address of the final destination. Routing is always based on network number.
NetAtlas Enterprise 1.00 User’s Guide Figure 102 Switch Manager Menus The following table describes the options in the switch manager screen. Table 61 Switch Manager Menus Overview LABEL MENU Window Exit Select Exit to close the switch manager screen. Admin Access Use this screen to display filtered logs generated by a switch(es). Database Management SUB-MENU DESCRIPTION Backup and Restore (EMS DB) Use this screen to backup or restore a switches configuration.
NetAtlas Enterprise 1.00 User’s Guide Figure 103 Switch Manager: Admin: Access Log The following table describes the fields in this screen. Table 62 Switch Manager: Admin: Access Log LABEL DESCRIPTION Log Filter Port Select a port or All Ports for which you want to view switch login data via the EMS. Log Type Select the type of logs which you want to view for the selected switch and port(s). Login User Select All Users to view logs for all access attempts to a switch via the EMS.
NetAtlas Enterprise 1.00 User’s Guide Table 62 Switch Manager: Admin: Access Log LABEL DESCRIPTION Port This field displays the selected switch port number on which the log was generated. Description This field displays further information about the log. Delete Click Delete to delete a select log from the list of log entries. Close Click Close to close this screen. 14.2.
NetAtlas Enterprise 1.00 User’s Guide Figure 105 Switch Manager: Database Management: Scheduled Backup The following table describes the fields in this screen. Table 64 Switch Manager: Database Management: Scheduled Backup LABEL DESCRIPTION Backup Schedule Frequency Scheduled backups can be performed on Daily, Weekly or Monthly. Select a radio button to schedule firmware backups starting from the date and time specifed below. The default setting is No Backup.
NetAtlas Enterprise 1.00 User’s Guide Figure 106 Switch Manager: Database Management: Log Storage The following table describes the fields in this screen. Table 65 Switch Manager: Database Management: Log Storage LABEL DESCRIPTION Storage Configuration Configure the following fields to retain daily records. Select the first radio button and a number (in thousands) from the drop-down list box to retain that number of records. All records prior to these records are cleared every 24 hours.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 15 Performance This chapter describes the interface performance screen, graph setup and table setup. View Ethernet history statistics for your switch network. 15.1 Interface This section shows you how to configure what you want to display in a performance table or graph. 15.1.1 View Interface Performance Click Performance and then Interface in the EMS main menu.
NetAtlas Enterprise 1.00 User’s Guide Figure 107 Performance: Interface The following table describes the labels in this screen. Table 66 Performance: Interface 149 LABEL DESCRIPTION Interface Select an interface (or port) from the drop-down list box. Rx Counters The following fields display the types of packet counters received on this interface. Tx Counters This following fields display the types of packet counters transmitted on this interface.
NetAtlas Enterprise 1.00 User’s Guide Table 66 Performance: Interface (continued) LABEL DESCRIPTION HC-Multicast Pkts Select this option to show the number of multicast packets (High Capacity (HC) 64 ~ 1518 octets long) dropped because they either had a bad Frame Check Sequence (FCS) or none-integer number of octets (alignment error).
NetAtlas Enterprise 1.00 User’s Guide Figure 109 Edit Table Entry Variable Name Variable Values Variable Set Button Previous and Next Page Buttons Expand First Get Next Stop Set All Done Help The following table describes the labels in this screen. Table 67 Edit Table Entry 151 COMMAND DESCRIPTION Variable Names The first vertical column contains the variable names; these are the names of fields in the selected table. These names are set by SNMPc and cannot be changed.
NetAtlas Enterprise 1.00 User’s Guide Table 67 Edit Table Entry (continued) COMMAND DESCRIPTION Next Click the Next button to obtain the next entry of the table from the node, using an SNMP GetNext operation. The variable values are updated. If there are no more entries in the table, a message is displayed. You can specify a starting point for the GetNext by entering index values.
NetAtlas Enterprise 1.00 User’s Guide Figure 110 Expand Field The Expand screen shows the variable value in a larger edit box, so you can more easily enter a long value. It also shows the variable type and a description from the MIB source file. Possible variable types are shown in the following table. Table 68 Variable Types TYPE DESCRIPTION Number This can be an INTEGER, COUNTER, GAUGE or Time Ticks. Data is normally represented as a decimal number.
NetAtlas Enterprise 1.00 User’s Guide Figure 111 Graph Menu Bar Restart Save to Bar Graph File Chart Pause Graph Poll Interval Line Pie Distribution Graph Chart Paging Controls Vertical Scale 15.3.1 Graph Styles Use one of the style buttons to change the graph style to one of the following: Table 69 Edit Table Entry STYLE DESCRIPTION Line Each variable is displayed as a line, with time as the horizontal axis. The vertical axis represents the size of each polled value for each poll interval.
NetAtlas Enterprise 1.00 User’s Guide Figure 113 Chart Color Codes and Line Styles You may also edit the color code and line style for a variable in the dialog box as described in the following table. Table 70 Edit Style Dialog Box FIELD DESCRIPTION Display Check Display to view information about this variable in chart format. Color Choose a color from this drop down list. Style Choose a line style from this drop down list. Scale Select the scaling multiplier from this drop down list.
NetAtlas Enterprise 1.00 User’s Guide Table 71 Graph Variables (continued) LABEL DESCRIPTION Scale This is the scaling multiplier. Cur This is the current value of the variable. Min This is the minimum value of the variable. Max This is the maximum value of the variable. Ave This is the average value of the variable. Total This is the total value of the variable. Baseline This is a measure of the typical variable behavior.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide CHAPTER 16 Troubleshooting This chapter covers potential problems and the corresponding remedies. 16.1 General Installation Problems Table 72 General Installation Problems PROBLEM CORRECTIVE ACTION SNMPc, Make sure that the computer you want to install the SNMPc and MySQL has the MySQL will not correct hardware and Operating System (OS) specifications. See Section 1.2 on page install properly 22 for a list of installation requirements.
NetAtlas Enterprise 1.00 User’s Guide Figure 115 EMS: Remove 2 Select ZyXEL NetAtlas Enterprise V1.00 and then click Change/Remove (or Add/ Remove depending on your version of Windows). 3 Click Yes when asked to confirm removal. The Uninstall Shield now runs. 4 Click OK when the uninstall has successfully completed. Restart the computer when prompted. 16.
NetAtlas Enterprise 1.00 User’s Guide 16.5 Problems Accessing the EMS Table 75 Problems Accessing the EMS PROBLEM CORRECTIVE ACTION When I click the Switch Manager icon, I cannot access the EMS Shutdown and restart both MySQL and the SNMPc manager. The EMS may already be running. Check your Windows task bar.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide Appendix A SNMPc Network Manager This appendix gives a brief overview of the SNMPc Network Manager. Starting the SNMPc Network Manager You must have SNMPc properly installed before you can use the EMS; please refer to the Castle Rock web site at www.castlerock.com or see your SNMPc user's guide. You may start the SNMPc Network Manager manually or automatically each time you turn on your computer.
NetAtlas Enterprise 1.00 User’s Guide Figure 116 Automatic Startup SNMPc Main Window The following figure and table show the elements of the SNMPc main window.
NetAtlas Enterprise 1.00 User’s Guide Table 76 SNMPc Main Window ELEMENT FUNCTION Main Button Bar Buttons and controls to execute common commands quickly. Hold the cursor over an icon to see a tool tip. Edit Button Bar Buttons to quickly insert map elements. Hold the cursor over an icon to see a tool tip. Selection Tool Tabbed control for selection of objects within different SNMPc functional modules. Event Log Tool Tabbed control for display of filtered event log entries.
NetAtlas Enterprise 1.00 User’s Guide • To quickly view events for a particular device, first select the device and then use one of the View Events buttons (or the View, Active Events and View, History Events menus). This will show the device events in a separate window in the View Windows area. • To remove one or more events, select the events and press the Delete key. • To acknowledge (remove current status of) an event, right-click on an event entry and click Acknowledge.
NetAtlas Enterprise 1.00 User’s Guide Figure 118 SNMPc Main Button Bar Icons Figure 119 SNMPc Edit Button Bar Icons Note: For more detailed information, please see www.castlerock.com.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.00 User’s Guide Appendix B Alarm Types and Causes This appendix shows examples of probable alarm types and causes.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.
NetAtlas Enterprise 1.
