Submittal Sheet

Page 1 of 1
Rev. K
Date: 1/20
Document No. TMV-ZW1070XL
Product No. Mode ZW1070XL
Model ZW1070XL
Aqua-Gard
®
Thermostatic Mixing Valve
Zurn Industries, LLC | Wilkins
1747 Commerce Way, Paso Robles, CA U.S.A. 93446 Ph. 855-663-9876, Fax [phone]
In Canada | Zurn Industries Limited
7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, 877-892-5216
www.zurn.com
FLOW RATES (GPM)
PRESSURE LOSS (PSIG)
0
20
40
60
0510 15
20
138
276
414
0.30.630.95
1.3
PRESSURE LOSS (kPa)
FLOW RATES (l/s)
MODEL ZW1070XL (STANDARD & METRIC)
Application
Ideal for use where Lead-Free* valves are required. The
Zurn Wilkins Model ZW1070XL Aqua-Gard
® Thermostatic
mixing valve is designed to be installed at the point of use
to assist in the prevention of scalding. The valve's extremely
rapid response rate make it most suitable for installation at
plumbing fixtures and appliances for the final control of water
temperature. The ZW1070XL is ASSE 1070 listed for fixtures,
sinks, lavatories or bathtubs and will mix hot and cold water
from the distribution system to a final safer temperature of
95-115°F (35-46°C). Multiple end configurations make this
valve suitable for all residential and commercial installations.
Standards Compliance
• ASSE® Listed 1070
• IAPMO® Listed
• CSA® Certified B125.70
• Meets the requirements of NSF/ANSI 61-9*
*(0.25% MAX. WEIGHTED AVERAGE LEAD CONTENT)
Materials
Body Low Lead Cast Bronze, ASTM B 584
W/Chrome Plating ASTM B 456
Service Condition #2
Internal brass Low Lead Brass, ASTM B 927,
UNS C27450
Piston Polysufone
Guide Tube Noryl GFN2
Spring & Screen 300 Series Stainless Steel
Seals Viton
Checks Noryl GFN2
Dimensions & Weights (do not include pkg.)
NSF/ANSI 61-9
MIXED
C
H
H
C
C
H
C
H
MIXED
Sensor Faucet
INDIVIDUAL USE SINGLE USE
Piping Instructions
The device is designed to be installed at a single outlet.
It may be used to supply individual outlets when there
is sufficient supply pressure. It is suggested to use ball
valves on the hot and cold inlet supplies.
C
C
MIX
B
H
A
XL
MODEL INLET & OUTLET
DIMENSIONS (approximate)
WEIGHT
A B C
in. mm in. mm in. mm lbs. kg
38-ZW1070XLCOMP 3/8" Compression 5 11/16 145 3 5/8 92 5 13/16 148 2 1
12-ZW1070XL 1/2" FNPT
5 7/16 138 3 3/8 86 5 1/4 133 2 1
12-ZW1070XLC 1/2" CU Sweat
12-ZW1070XLCPVC 1/2" CPVC 5 7/8 149 3 13/16 97 6 3/16 157 2 1
12-ZW1070XLPEX 1/2" Barb 5 9/16 141 3 1/2 89 5 9/16 141 2 1
12-ZW1070XLPEXF1960 1/2" Barb 5 3/8 137 3 5/16 85 5 1/4 133 2 1
34-ZW1070XL 3/4" FNPT
5 1/2 140 3 1/2 89 5 7/16 138 2 1
34-ZW1070XLC 3/4" CU Sweat
34-ZW1070XLCPVC 3/4" CPVC 5 7/16 138 3 3/8 86 5 5/16 135 2 1
34-ZW1070XLPEX 3/4" Barb 5 9/16 141 3 1/2 89 5 9/16 141 2 1
34-ZW1070XLPEXF1960 3/4" Barb 5 3/4 146 3 11/16 94 5 11/16 151 2 1
34-ZW1070XLM 3/4" MNPT 6 1/4 159 4 1/4 108 7 178 2 1
1-ZW1070XLC 1" CU Sweat 5 1/2 140 3 7/16 87 5 3/16 132 2 1
Flow Characteristic
Features
Sizes: 3/8", 1/2", 3/4", 1"
Outlet Temp. Range 95-115°F max (35-46°C)
Temperature Hot Supply 120-195°F max. (49-90.5°C)
Temperature Cold Supply 39°F-80°F(3.8-26.6°C)
Set Temperature Accuracy +/- 3°F(1.78°C)
Max. Working Pressure (inlet) 145 psi
Temperature must be field set
Max. Pressure Differential is 15 psi between Hot & Cold inlets
Flow rate @ 45 psi pressure loss 10 gpm
Min. Flow Rate 0.25 gpm
CPVC tailpiece - Maximum Hot water Temperature of
180°F @ 100 psi.
- Cold water rated Temperature of
73.4°F @ 400 psi.
Options
 PF - with Z-Bite™ push fit tailpiece connections
(1/2" - 1" only)
 PR - with Z-Press™ press fit tailpiece connections
(3/4" - 1" only)