Mobile Cam (Model：MF68 ) User Manual Edition: 1st edition, February, 2008 Copyright © 2008 by ZTE Corporation
MF68 Contents 1 Warning and precautions ........................................................6 1.1 Precautions............................................................................................................... 6 1.2 Aircraft safety............................................................................................................ 7 1.3 Precautions for medical Mobile Cams and facilities ............................................... 7 1.4 General safety ..............................
MF68 2.1 Overview ................................................................................................................. 11 2.2 Technical parameters..............................................................................................12 2.3 Environment requirement .......................................................................................12 2.4 Your Mobile Cam ....................................................................................................13 2.
MF68 4 Mobile CAM controlled by 3G video phone ............................25 4.1 Camera adjustment ................................................................................................ 26 4.2 Adjusting speaker volume...................................................................................... 26 5 Administrator main menu operation......................................27 5.1 Video phone main menu operation........................................................................ 28 5.5.
MF68 Thank you for using the Mobile Cam. To guarantee the Mobile Cam is always in best condition, please read this manual carefully and keep for further use. The pictures and contents in this manual are for your reference only. They might not be completely identical to your Mobile Cam.
MF68 1 Warning and precautions 1.1 Precautions The Mobile Cam contains delicate electronic circuitry and battery systems. You should treat it with care and pay particular attention to the following points: u Do not allow the Mobile Cam, battery or accessories to come into contact with liquids or moisture at any time. Do not immerse in any liquid. u The Mobile Cam can’t do the video call over 3 hours continuously. If the time is over 3 hours, it will shut off automatically.
MF68 u u The Mobile Cam may become warm during normal use. The Mobile Cam may also become warm while the battery is being charged. Use a damp or anti-static cloth to clean the Mobile Cam. Do not use chemical or abrasive cleaners as these could damage the case. 1.2 Aircraft safety u u Onboard an aircraft, please turn off your Mobile Cam before take-off. In order to protect aircraft communications systems from interference, do not use the Mobile Cam while in flight.
MF68 u If on premises with special demands, such as hospital or healthcare facilities, please pay attention to the restriction of the use of the Mobile Cams. Switch off your Mobile Cam if required. 1.4 General safety u u Keep the Mobile Cam out of the reach of small children. The Mobile Cam may cause injury if used as a toy. The operation of some medical electronic items, such as hearing aids and pacemakers, may be affected if the Mobile Cam is used in close proximity.
MF68 not switch on the Mobile Cam until it has been checked by qualified and approved installers. 1.6 Vehicles equipped with an air bag u An air bag inflates with great force. Do not place objects, including installed or portable wireless equipment in the area above the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. 1.
MF68 u This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and(2)this device must accept any interference received, including interference that may cause undesired operation. u NOTE:The phone has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
MF68 —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. u We,ZTE Corporation,declared that the product is installed with battery separately in the box.The FCC ID label is placed on the mobile cam clearly visible to all persons at the time of purchase. 2 Getting to know your Mobile Cam 2.
MF68 2.2 Technical parameters Type Mobile Cam(Model: MF68) Dimensions（W×L×H） 105mm×85mm×112mm Weight 263g (with integrated battery) Camera 0.3 megapixel (solar/infrared dual mode) Battery Continuous standby time 120-200 hours Recording time (in sunlight environment) 7-12 hours Recording time (in infrared environment) 3-5 hours Video communication time (in sunlight environment) 2-3 hours Video communication time (in infrared environment) 1.6-2.6 hours Charging time 5 hours 2.
MF68 Relative humidity: 5％～95％（without dew） Power supply: 220V supply, integrated spare battery This mobile camera is only used in WCDMA network. 2.
MF68 1.Camera 2.Power indicator 3.Signal indicator 4.Infrared spotlight 5.Infrared sensor 6.MIC Camera: The camera can rotate upward at an angle up to about 40 degrees, downward at an angle up to about 5 degrees, and left and right at an angle up to about 45 degrees. Power indicator: Indicates the level of charge in your battery. There are five colors: white, blue, cyan, green and red. Signal indicator: Indicates local network signal strength. There are two colors: Red and Green.
MF68 1. SIM/USIM card slot 2. T-Flash card slot 3. Power 4. Reset 5. Speaker 6. Charger Connector On the back of the unit, there are 3 slots: SIM/USIM, T-Flash and charger. Please refer to 1.5.1, 1.5.2 and 1.5.4 respectively for details. There are also 2 buttons: l POWER: Power on/off. l RESET: Restart the system. White list and password will not be affected.
MF68 2.5 Getting started Make sure you follow the operation procedure before using the Mobile Cam. l Insert a 3G SIM/USIM card. l The battery should be fully charged before you use the Mobile Cam, otherwise the Mobile Cam may not function correctly. l Set date and time. See details in Section 4.2. 2.5.1 SIM/USIM card Be sure to insert a 3G SIM/USIM card before you use the Mobile Cam. Note: u A SIM/USIM card set with PIN code cannot be used normally in the Mobile Cam.
MF68 u end inward, until you hear “a cracking sound”. 4. Insert the plastic plug back into the SIM/USIM card slot to keep it from dust. Removing SIM/USIM card 1. Make sure your charger is disconnected, then press and hold down the power key until the Mobile Cam is powered off. 2. Pull out the plastic plug covering the SIM/USIM card slot. 3. Press the SIM/USIM card until you hear “a cracking sound”, when the SIM/USIM card will pop up to be pulled out. 4.
MF68 2.5.2 T-FLASH The T-FLASH card is used to save a recorded video file. The process of inserting and removing the T-flash card is the same as the SIM/USIM card. Note: u When the T-FLASH card is inserted, the metallic surface is upward, which is different from how to insert the SIM/USIM card. 2.5.3 Battery Your Mobile Cam is equipped with a Lithium ion battery. You do not need to purchase a new one.
MF68 2.5.4 Charging the battery Please use only the provided charger to charge the Mobile Cam. In the charging process, the POWER indicator is blue. When the battery is fully charged, the POWER indicator will turn from blue to green. 1. Connect the adapter to the adapter connector . 2. Plug the other end of the charger into an appropriate electrical outlet. 3. When charging is complete, disconnect the adapter from the electrical outlet and remove from the adapter connector.
MF68 2.5.5 Understanding indicators The Mobile Cam has two indicators on the front panel – one for the level of charge in your battery and the other for local network signal strength Signal indicator：Indicates local network signal strength. Detail Description Red ( flash) No network strength or low network strength Green ( flash) Normal network strength Power indicator：Indicates the level of charge in your battery.
MF68 Flash means the indicator blinks every 5 seconds. Flash quickly means the indicator blinks every 2 seconds. Infrared spotlight: If the switch of infrared mode is set “on”(please refer to Section 4.2), when light is weak (less than 20 LUX), the Mobile Cam will shut down daylight mode and start infrared mode automatically. At that time, Infrared spotlight will be turned on to provide illumination. 2.6 Power on/off Power on 1 Ensure that your SIM/USIM card has been inserted and the battery is charged.
MF68 2. Then you can use two screws (screw 2) to fix the bracket firmly onto the ceiling. 1.Body 2.Brocket 3.Screw1 22 4.Screw2 5.
MF68 3 White list The white list contains only legitimate user numbers. The maximum number of records that can be saved in the white list is 20. 3.1 Mobile Cam’s own phone number Insert a valid SIM/USIM card. The SIM/USIM card number is also the Mobile Cam number. If the PIN code of the SIM/USIM card is locked, you should unlock the code by using in another mobile phone. Otherwise, that card cannot be used by Mobile Cam. Also, Mobile Cam cannot operate if the SIM/USIM card is invalid. 3.
MF68 SMS command that whether the beep switch is on or off). After 3 consecutive incorrect PIN code entries, or if you have not been able to enter the PIN code within 60 seconds, the Mobile Cam will be disconnected automatically. If the PIN code is correct, AD will enter the video call interface. Note: Once you set the AD number on the Mobile Cam, you can check or revise the time by SMS. For details, please refer to the section on SMS command operation.
MF68 The AD can also set the other user number via the video phone menu or SMS commands (see Section 4.1, 4.2). AD can also set validation for non-white list users (see Chapter 5). 3.4 User entry White list user: Phone numbers added to white list (including AD number). The white list user can dial the mobile camera without the need to input a PIN (this function depends on the SMS setting).
MF68 4.1 Camera adjustment White list users can adjust the angle, brightness and zoom of the camera. Rotate the camera right/ left 45°, upward 40° , downward 5° and control 3X digital zoom.
MF68 5 Administrator main menu operation The first person to dial the Mobile Cam successfully becomes the administrator (AD). The administrator can operate the Mobile Cam by video phone menu and SMS command.
MF68 5.1 Video phone main menu operation After a video call is connected, the administrator should press “0” key to enter the submenu. Follow the instructions to add users, delete users, change PIN code and administrator number and record video. Note: Screens are for reference only. If a discrepancy exists between the actual screen and above photo, the actual screen will be deemed to be correct.
MF68 5.5.1 Adding users è è In main menu, press the “1” key to enter the Add User interface. Enter the phone number of the new user, and end by pressing “*” key. Press“*”key again to confirm the operation, press “#” key to cancel the operation and go back to main menu. 5.5.2 Deleting user è è In main menu, press “2” key to enter the Delete User interface. Press “*”key for paging down. Select the serial number before the phone number you want to delete.
MF68 5.5.3 Changing PIN code è è è In main menu, press “3” key to enter the Change PIN interface. Enter the current PIN code and end with“*”key, then enter the new code and end with “*”key. Press “*”key to confirm the input. If you input the wrong number, press“#” key to go back to main menu.
MF68 5.5.4 Changing administrator number è è In main menu, press “4” key to enter the Administrator Change interface. Enter the new administrator phone number and end by “*” key. Press “#” key to cancel operation and go back to main menu. 5.5.5 Video recording è è In main menu, press “5” key to enter the Video recording interface. You will see free T-flash space and recording time available.
MF68 The recorded file will be saved in the T-Flash card and will be named yyyymmddhhmm_xx.3gp (yyyymmddhhmm represents year, month, day, hour and minute. The year contains 4 digits, while the others all contain 2 digits. For example, 200605011230 stands for 12:30 May 1, 2006. XX stands for the serial number, such as 00, 01 and so on). Maximum recorded video file size is 3 hours. If the recorded time is longer than 3 hours, there will be several files.
MF68 switch setting. Command Adding a new user Deleting a user Modifying user PIN code Modifying administrator number Setting the language Getting white name list BEEP on/off when video call is connected Help SMS COMMAND #adduser*[number]#[pin]# #deluser*[number]#[pin]# #modpin*[newpin]#[pin]# #modad*[oldnumber]*[newnumber]#[pin]# #setlanguage*en|ar|es|ch|tw #[pin]# The default is English.
MF68 Setting time Getting time Setting the switch to control whether user needs to input PIN code every time Setting the switch of infrared mode Setting the switch of the led indicators Setting the validation of non-white list user #settime*[yyyymmddhhmm]#[pin]# #gettime#[pin]# #pin*on|off#[pin]# The default is “off”. If the switch is set as “on”, the caller has to input the PIN code every time, whether his number is in the white list or not.
MF68 Get phone status Set access mode the caller is roaming or the caller disables the phone to send its number), or 2. the incoming call’s number exceed 20 digits, or 3. the white list reaches its limit and the incoming call’s number isn’t in the white list. If the entered number is in the white list, then the user will be further prompted for the PIN and video call will proceed if the PIN is correct.
MF68 wl: White list access mode is the default mode (The user connecting the monitor will be saved in the White list. Your role will be authenticated before you access the monitor) Set power ring volume level Clear the White list fr: Free access mode ( you can connect with the monitor freely without authentication. There is no White list in this access mode and any user can access the monitor.
MF68 20 digits . ( “+” will be ignored) . [pin]：Indicates user PIN code. It should be in 4 digits. [newpin]：Indicates new user PIN code. It should be in 4 digits. [oldnumber]：Indicates old administrator number [newnumber]：Indicates new administrator number |：Indicates “or” l [yyyymmddhhmm]：Indicates year, month, day, hour, minute. For example: 12:30, May 1, 2006 is displayed as 200605011230. Note: Please use a 3G mobile phone to make sure the SMS center number in your SIM/USIM card is correct.
MF68 6 Infrared/daylight Operation Modes and Non-white List User Validation Function The Mobile Cam has two operation modes – daylight mode and infrared mode. In the infrared mode, it turns on infrared spotlight. If the switch of infrared mode is on (please refer to Section 4.2) and the light is weak (less than 20 LUX), the Mobile Cam will shut down daylight mode and start infrared mode automatically.
MF68 2) When the switch of the validation of non-white list user is set as “off”. the Mobile Cam won’t allow the video call. Note: please see Section 2.4 for normal white list operation. Rules for number verification: - If an incoming call number is more than 8 digits, on the last 8 digits will be verified. - If an incoming call number is less than 8 digits, the whole number will be verified. - “+” symbol is not included for verification (IDD call in number may have “+” symbol).
MF68 7 Trouble Shooting When you encounter problems in the operation of SG88, please look up the trouble shooting before you contact our technical support. Q: Why can’t SG88 be powered on? A: Please check the color of the power indicator If the power indicator isn’t lightened or there is no power-on music, please charge the mobile cam. If the color of power indicator is Cyan, please check if the USIM card is valid and is not locked(You can try the USIM card in a handset.
MF68 mobile cam successfully for the safety. Q：Why isn’t the communication stable or can’t I dial video call in some places? A: The communication can be unstable or the video call can’t be dialed when you are in some places where the signal is unstable. Please go to some other places to try again or contact your service provider. Q: Why isn’t there any notifying tone when dial up a video call? A: There are relative settings in the mobile cam.
MF68 prompt SMS “The white list reaches its limit, you can’t be connected.” . At this time, you can delete some of the numbers in the white list through the AD number. Q: If there is an unexpected situation when the mobile cam doesn’t work, what shall I do? A: You can press Power key to restart the mobile cam. Q: What shall I do if I forget the password or the ad number? A: Please send your mobile cam to the retailer or the appointed maintenance place to reset the password.
MF68 Declaration of RoHS Compliance To minimize the environmental impact and take more responsibility to the earth we live, this document shall serve as formal declaration that the SG88 manufactured by ZTE CORPORATION are in compliance with the Directive 2002/95/EC of the European Parliament RoHS (Restriction of Hazardous Substances) with respect to the following substances: （1）Lead (Pb) （2）Mercury (Hg) （3）Cadmium (Cd) （4）Hexavalent Chromium (Cr (VI)) （5）Polybrominated biphenyls (PBB’s) （6）Polybrominated d
