A002ZT USB Modem Quick Start Guide 1
Getting Modem to Know Your Your modem supports data services through the mobile phone network, enabling you to communicate anytime and anywhere. The following figure is only for your reference. The actual product may be different.
1. Rotatable USB connector 2. Indicator light Red • blinking Red on There is no nano-SIM card inserted or the nano-SIM card is damaged. • • • The PIN or PUK is enabled. The device is just powered on. The device is searching for available networks. • There is no network service available. Green The device is connected to the 2G/3G on mobile network and data is being transferred. Green The device is registered to the 2G/3G blinking mobile network.
Installing Card the nano-SIM 1. Open the nano-SIM card slot cover. NOTE: Do not remove the cover rudely, because it is connected with the device. 2. Install a nano-SIM card to the nano-SIM card slot. WARNING! To avoid damage to the device, do not use any other kind of SIM cards, or any non-standard nano-SIM card cut from a SIM card. You can get a standard nano-SIM card from your service provider. 3. Close the nano-SIM card slot cover.
Connecting the Modem to Your PC Rotate the USB connector and insert the modem into your computer’s USB port securely. The operating system automatically detects and identifies your modem and installs the software automatically. NOTE: If the system does not launch installation automatically, you can double-click the modem installation icon in My Computer > ZTEMODEM to install the software.
Logging in to the Device Manager Website 1. Launch the Internet browser and enter http://192.168.0.1 in the address bar or click on your desktop. 2. Click Login and enter the password to log in to the Device Manager Website. NOTE: View the label on the device to get the default password.
Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Auto or Manual mode. The default mode is Manual. Mode Operation Auto Your device is automatically connected to the Internet. To set Auto mode: 1. Log in to the Device Manager Website. 2. Select Settings > Mobile Network Settings > > Network Connection Mode > Auto, and then click Save Changes. Manual 1. Log in to the Device Manager Website. 2.
Getting More Help You can get help by: Sending an email to mobile@zte.com.cn Visiting www.ztedevices.
LEGAL INFORMATION Copyright © 2020 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.
Warning and Notice Using Your Modem If inadequately shielded, some electronic devices may be affected by the electromagnetic interference caused by the modem, such as the electronic system of vehicles. Consult the manufacturers of such devices before using the modem if necessary. Operating the modem may interfere with medical instruments such as hearing aids and pacemakers. Always keep the modem more than 20 centimeters away from such medical instruments when your modem is turned on.
necessary. Otherwise the performance of the modern may be affected. Keep the modem out of the reach of little children. The modem may cause an injury if used as a toy. When the modem is operating, do not touch the metallic parts. Failing to do so may cause burns. Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the modem and violate the related national regulations about telecom terminals.
+60 °C and a humidity between 5% and 95% are recommended. Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. ii. Reasonable abrasion. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual.
ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.
Specific Absorption Rate (SAR) Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization FCC and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 1.
§ 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. § 15.
the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation equipment and receiver. between the -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.
