MF65M Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.
Getting to Know Your Device Appearance The following figure is for your reference only. 1. 2. 3. 4. 5. 6. LED Indicators Power Key WPS Key Charging/micro-USB Jack (U)SIM Card Slot microSDHC Card Slot NOTE: The microSDHC™ logo is a trademark of SD-3C, LLC.
Getting to Know Your Device Indicators When the device is powered on, the following icons may be lighting. For a description of the icons, refer to the following table. Indicator Status Description Error status. Not registered to the mobile network, no (U)SIM card Red solid inserted or no network service Network available. Green solid Green blinking Registered to the mobile network. Connected to the mobile network and data is being transferred. Blue solid Wi-Fi is active.
Getting to Know Your Device Blue solid You have unread messages. SMS Blue blinking off You have new messages. No unread messages. Red solid The battery is low. Please charge / blinking the battery. Battery Green blinking Green solid off The battery is being charged or in standby mode. The battery level is middle or high. Your device is not being charged, or the battery is not inserted.
Getting to Know Your Device Connection Scenarios The device can access the Internet in two ways and it allows multiple clients to surf on the Internet at the same time. The following figures are for your reference only. • 3G Mode: A (U)SIM card can be used to access the Internet. • Internet Wi-Fi Mode: Your device can be connected to a WLAN device (such as a hotspot device or wireless router) through Wi-Fi to access the Internet. The WLAN device must be already connected to the Internet.
Getting to Know Your Device Installing Your Device 1. Slide the back cover and remove it. NOTE: Do not remove the cover rudely. 2. Install a (U)SIM card to the (U)SIM card slot. WARNING! Your device does not support the micro-SIM and nano-SIM card or any other non-standard SIM cards. To avoid damaging the device, do not use those cards or any card holders.
Installing Your Device 3. Install the microSDHC card if necessary.
Installing Your Device 4. Install the battery. 5. Close the back cover.
Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Make sure your computer or other client devices have enabled Wi-Fi, and search for available wireless networks. NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically. 3. Select the Wi-Fi name (SSID) of your device, and click Connect. 4. Enter the Wi-Fi password if necessary, and click OK.
Connecting to Your Device Using a USB Cable 1. Connect a computer to your device with a USB cable. 2. Power on your device. The operating system detects and identifies new hardware, and automatically installs the hardware. NOTE: If the system does not automatically launch installation, you can click the device installation icon in My Computer to install the software. 3. Wait until the computer is connected to your device successfully.
Logging in to the 3G Mobile Hotspot Configuration Page 1. Make sure the connection between your device and the client device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 or http://virgin.wifi in the address bar. NOTE: It is recommended that you use IE (7.0 or later), Firefox (15.0 or later), Opera (10.0 or later), Safari (4.0 or later), or Google Chrome (10.0 or later). 3. Enter the password to log in to the 3G Mobile Hotspot configuration page.
Accessing the Internet 3G Mode After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Operation Automatic Your device is automatically connected to the Internet, and you can surf on the Internet through the client. Manual 1. Log in to the 3G Mobile Hotspot configuration page. 2. Select Settings > Network Settings > Dial-up Settings > WAN Connection Mode > Manual, and then click Apply. 3.
Accessing the Internet Internet Wi-Fi Mode 1. Log in to the 3G Mobile Hotspot configuration page. 2. Select Settings > Internet Wi-Fi. 3. Set the Internet Wi-Fi Switch and Preferred Network, and click Apply. 4. You need to set Internet Wi-Fi Switch to Enable and Preferred Network to Wi-Fi. 5. Connect to the Wi-Fi hotspot. The following two methods are for your reference. u u Select a Wi-Fi hotspot listed in the Wi-Fi Hotspot area, enter a pass phrase in the Pass Phrase text box and click Apply.
Accessing the Internet After the client device is connected to the Wi-Fi hotspot successfully, you can access the Internet. Configuring Your PC The following procedure describes how to configure the Internet Protocol in the Windows 7 operating system for your Wi-Fi connection. 1. Right-click Network and select Properties. 2. Select Change adapter settings. 3. Right-click Wireless Network Connection and select Properties. 4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties. 5.
Warning and Notice To the Owner • • • • If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on.
Warning and Notice • Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected. • • • Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such event, cool the device in a well-ventilated place before turning on for normal use.
Warning and Notice • • • • • • Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. The device is not waterproof. Keep the device dry and store it in a shady and cool place. Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry. Handle the device carefully. Do not drop, bend or strike it.
Warning and Notice Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. Reasonable abrasion. ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a v. ZTE-certified individual.
Warning and Notice End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users’ sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.
LEGAL INFORMATION Copyright © 2014 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.
Troubleshooting Problem The connection between your device and a PC through a USB cable cannot be established. The connection between your device and a cli- Recommended Action • Install the software, and run the installation program in the path of My Computer. • If the driver of your device is abnormal, reinstall the software. You need to uninstall the software first. • Ensure that the Wi-Fi function is enabled. Refresh the network list and select the correct SSID.
Troubleshooting Problem Recommended Action • Ensure that your (U)SIM card is • The client connected to the device cannot ac- • cess the Internet. • available. Change the location and find a place with good signal. Check the settings of the WAN connection mode. Contact your service provider and confirm your APN settings. • The client cannot access the Internet in Internet • Wi-Fi mode. Ensure that the WLAN device has already been connected to the Internet.
Troubleshooting Problem Recommended Action • The 3G Mobile Hotspot configuration page cannot be visited. • • Enter the correct address. The default address is http://192.168.0.1 or http://virgin.wifi. Use only one network adapter in your PC. Do not use any proxy server.
