ZTE MF645 HSUPA USB Modem User Manual 1
Contents 1 Modem Introduction .........................................................4 1.1 Introduction .......................................................................................... 4 1.2 Warning and Notice ............................................................................. 4 1.3 Applicability Scope .............................................................................. 7 1.4 System requirements ........................................................................... 7 1.
.5.5 Alert settings ........................................................................... 46 3.6 Help ................................................................................................... 46 3.7 MicroSD card ..................................................................................... 48 4 FAQ & Answers ...............................................................
1 Modem Introduction 1.1 Introduction Thank you for purchasing ZTE MF645 HSUPA USB Modem. To guarantee the modem always in its best condition, please read this manual carefully and keep it for further use. The pictures, symbols and contents in this manual are just for your reference. They might not be completely identical with your modem. We operate a policy of continuous development. We reserve the right to update the technical specifications in this document at any time without prior notice.
Store the modem out of the reach of little children. The modem may cause injury if used as a toy. Modem Please use original accessories or accessories that are authorized. Using any unauthorized accessories may affect your modem’s performance, and violate related national regulations about telecom terminals. Avoid using the modem near metallic structure device or establishment that can emit electromagnet wave. Otherwise it may influence receiving signals.
Health and safety information Radio Frequency (RF) Energy This model phone meets the government’s requirements for exposure to radio waves. This phone is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government: The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.
Systems supported Supports most types of laptop and desktop PC. Operating systems Windows XP, Vista, MAC OS SMS service, Data service, Applications Functions management, Data concurrent, watch TV，support MicroSD card, etc. Digital TV protocol DVB-H/DVB-T Network Standards HSUPA/HSDPA/UMTS/EDGE/GPRS/GSM HSUPA/HSDPA/UMTS: 2100/1900/850MHz Frequency band GSM/GPRS/EDGE: 1900/1800/900/850MHz HSUPA: 2.0Mbps UL Transmission Temperature HSDPA: 7.
Blue(flash) Connected to the UMTS network. Cyan(normal) HSDPA in use.
2 Installation 2.1 Outline and Part Introduction 1. SIM/USIM Card Slot 2. Exposed Digital TV Antenna 3. Indicator 4. Modem Cap 5. USB Port 6. MicroSD Card Slot 7.
2.2 Software Installation The system will automatically detect and recognize the new hardware and display the new icon in the desktop status bar, indicating that the computer and the USB Modem have been connected properly. After a few seconds, there will show the following installation interface if the laptop and desktop PC supports automatic installation. If the laptop and desktop PC doesn’t support automatic installation, start the from the CD-ROM. The installation program by run the AutoRun.
2. Read the agreement carefully. If you agree, choose I accept the terms of the license agreement, and then click Next.
3. Select the folder that you want to install the software, and you can select a different path by clicking Change, then click Next; 4.
5.
6. Click Finish to complete the installation. Note: After MODEM Mobile Connection is installed, pull out the modem before restart the computer to avoid the damage to your modem. If you have problems with installation after the upper operation, please contact your service provider or ZTE. After the installation, select Start>Programs>MODEM Mobile Connection，you can see MODEM Mobile Connection and Uninstall. There will be a Shortcut icon on the desktop just as follows.
2.3 Hardware Installation 1. Insert the SIM/USIM card into the USB Modem: Your USIM card stores your service details, phonebook and text messages. You can obtain it from a mobile phone service provider when you sign on as a subscriber. To install SIM/USIM card z Remove the modem cap, then the USB connector is visible. z Pull out the plastic socket above the USB connector and you can hear a click when the SIM/USIM card gets unlocked. Note: Do not pull the socket rudely. Otherwise the socket will get damaged.
z Insert the plastic socket into the modem. You can hear a click when the SIM/USIM card locks into place.
To Remove the SIM/USIM card from the USB modem z Remove the USB cap. z Pull out the plastic socket slightly, and you can hear a click when the SIM/USIM card gets unlocked.
z Pull the SIM/USIM card out of the card socket.
z Insert the socket into the modem. 2. Install memory card You can use a compatible MicroSD card to save more data. Only MicroSD card is supported by the modem and do not insert other memory card into the modem. z Open the MicroSD card cover.
z Insert the MicroSD card into the slot. Make sure the metal contact of the memory card orientated as shown in the following picture. z Close the MicroSD card slot cover.
The driver of the MicroSD card will be installed automatically when the modem driver is installed. Note: Maximum 8 GB MicroSD card is supported 3. Connect the USB Modem to your PC z Connect the USB Modem to the USB port and make sure that it is tightly inserted. z Your PC system will automatically detect and recognize the new hardware and display the new icon in the desktop status bar, indicating that the computer and the USB Modem have been connected properly.
3. Now you can safely remove your USB Modem. If you use a MicroSD card in the modem: 1. Left click the icon in the Windows system tray bar. Then a menu will popup and indicates the USB devices list as below: 2. Select Safely remove USB Mass Storage Device which is relevant to the MicroSD card. 3. Pull out the USB modem directly if you want to disconnect the modem from the laptop and desktop PC. 2.6 Software Uninstall 1. Close the application program before you uninstall the software. 2.
4. Make sure to remove Modem device from PC, and click Yes to start to uninstall MODEM Mobile Connection. The following interface indicates the uninstalling progress. 5. Click Finish to complete uninstalling of MODEM Mobile Connection.
3 Functions & Operation 3.1 Interface introduction 3.1.1 Main Interface The following picture is the starting screen of your MF645. Function button area System information area User area 1. Function button area There are six function button icons. Internet: Connect to the Internet. SMS: Send SMS and read SMS. Phonebook: Save and view the different information of the contact list. Settings: Set normal relative information for the modem. TV Enhance：Watch TV via DVB-H/DVB-T.
2. System information area Icons in this area show the system status and different kinds of tips. Icon Function Indicates the network signal intensity. There are 6 stages from none to the strongest . Indicates there are new SMS at present. Indicates the current status of Internet connection is not connected. Indicates the current status of Internet connection is already connected. P means it supports packet-switch （P）service. It is necessary for Internet connection.
system tray. If connected to the Internet, the minimized software won’t influence the download of data transfer or receiving SMS. When the application window is minimized, the system icons will display on the taskbar. Double click the icon to resize the display. 1. Taskbar Icons Description The USB Modem has been inserted into the computer. The USB Modem not been inserted into the computer. The USB Modem is offline. SIM/USIM card has not been inserted. No network signal. There is a new message.
Factory Settings: Reset your MF645 to factory settings. Help: View the Help information of the modem. About: View the information of software and hardware versions. Exit: Close the software and stop the modem from working. 3.2 Connecting Internet You can browse web pages after you have accessed to Internet with the help of modem, you can also receive SMS when surfing in the Internet. 1. Connect to Internet Click the Internet icon.
through the network. During the course of connecting, when the Connect button becomes Disconnect button, you can click Disconnect to cancel the connecting. Note: The modem has the function of locking the SIM/USIM card. If you use the SIM/USIM card provided by the other network provider, maybe you can’t connect to the network. If you have any problem, you can consult your network provider for further information. 2. Internet connection records Click to check the log of Internet connection history.
3.3 SMS Note: To make sure that the SMS can be used properly, at first, you should setup the correct SMS center number. Refer to section 3.5.4 Messages settings. Click the SMS icon to switch to the SMS interface and it will show the number of SMS in the inbox, outbox and draft box. You can click icons of InBox, OutBox, DraftBox and New Message to enter relative interface.
InBox: Save the received SMS. OutBox: Save the successfully sent SMS. Draft box: Save the editing SMS which haven’t been sent. The drafts can only be saved in PC side. New Messages: Write a new message. For example: “Message in InBox PC : 0 Item(s) (U)SIM Card: 16 Item(s)” means: The PC side has 0 short messages and there are 16 short messages in the Inbox of the SIM card , “SIM Card capability” means the SIM card can hold 20 short messages. Different SIM/USIM cards will have different capacities.
3.3.1 Read SMS Click the Inbox button or the SMS icon on the system information area to read the SMS saved in the box. . You can use the buttons under the menu to execute reading, replying, forwarding, move, delete, saving numbers functions and so on. 3.3.2 Create new message Click New Message button to input the recipient’s number and content.
The recipient’s number can be input directly or by entering the phonebook to select one/more/group records. The recipient’s amount can be one or more. Please use “;” to separate recipients. The SMS content can include 140 individual English characters (including English symbols. On the interface, there will show total characters. Click Send, the prompt screen will appear on the interface just as follows.
Select “Yes”, and then the edited short messages will be sent. After sent successfully, the SMS will be saved into outbox automatically. If it is not sent successfully, it will be saved to the draft box automatically. Sending SMS while browsing the web: When surfing the Internet, if your network supports, you can send short messages. Click SMS button icon, enter the short message interface to send short messages normally.
3.3.3 The SMS box Operating Guide Enter any of the InBox/OutBox/DraftBox to execute the following functions: Read: Read all the information of short messages. (The content of short messages, sender’s phone number, delivered date and time) Reply: Reply short messages to the sender. Forward: Send the short message to other recipients. Move: Change the saved position (at PC side or USIM/SIM card) of short messages to another position (at USM/SIM card or PC side).
execute multi-choice, and left click an item to add to selection. New message can not be received when the USIM/SIM card is full of short messages (Different USIM/SIM cards have different capacities), the system will indicate the inbox is full and make users clear the inbox at USIM/SIM card side, while new message can not be saved. 3.
2. New Group： You can add new group at the PC side. But you cannot add new group at the SIM/USIM side. Left click New > New Group and input the group name, Select contact records from the right contact list and drag them to the right group item, if you want to add contacts to a group. 3. Other buttons Description If any contact is selected, you can carry out the following steps: View: View the selected contact’s information. Delete: Delete contacts or groups.
Edit: Edit the information of selected contact. 3.5 Settings Click “Settings” icon to switch to the settings interface. It includes: Connection settings, Security settings, Network settings, Messages settings, Alert settings. Note: All the necessary settings are preset by default. There is no need to change such settings, if you want to change these settings, please consult with your service provider. 3.5.
View: View the selected configuration file. You can only view the default configuration files but can not edit them. Edit: Edit the selected configuration file. You can only edit the configuration files added by yourself. Set default: Select one configuration file from the list, and set it as the current using file. (2) Add new Configuration file Click Add button to add new connection information to the system.
3.5.2 Security Settings 1. Enable the PIN Code z z z Select the PIN enable check box. Click Apply button. Enter PIN code and click OK.
Note: If you enable the PIN code, you need to enter your PIN code every time before you start to use your MF645. 2.Change the PIN code z z z z z Make sure to enable the PIN code. Click Change PIN button. Enter the old PIN code. Enter the new PIN code twice. Click OK. 3. Backup Phonebook and SMS You can backup your Phonebook and SMS manually into the PC side. z Click Backup button. z Select the backup location in your PC. z Click Save. If you want to update your Phonebook and SMS, you can click Resume.
3.5.3 Network Settings 1. Select Network Automatic: The system selects the network automatically by the user’s selected rules and the network status. Manual: You can select the network manually: z Select Manual. z Click Apply button. z Select a proper network after the supplier list is shown in the window. icon. Note: The network you can use is shown after z Click Select button.
2. Select the Network Mode Automatic: The system selects the network automatically.
UMTS Only: The system selects UMTS network only. GSM Only: The system selects GSM network only. 3.5.4 Messages Settings Message Center: Set the message center number. You can use the default number preset by your service provider. If you want to edit it, please consult with your service provider for more information. Validity period: Set the time limit for saving SMS in the network side. (This function needs network supports.)In option：12 hours/A day/A week/The longest period.
3.5.5 Alert settings You can set Connection alert, Disconnect alert and Incoming SMS alert by yourself. These alerts will sound on the PC side. The audio file supports MP3, WAV, MID and WMA format. If you select Mute check box, you cannot hear a corresponding alert. 3.6 Watching TV You MF645 USB modem enables TV reception via DVB-H /DVB-T. After initiating the supplied TV software, you can search for the DVB-H /DVB-T signal and receive the encrypted channels on your PC.
Click Menu button to view Channel Guide, Setting, Change Language, and Help. The functions of playing operation button as follows: Click “Previous” button to watch the Previous previous program. Play Click “Play” button to watch TV. Next Click “Next” button to watch the next program. Pause Click “Pause” button to pause. Full Screen Click “Full Screen” button to display the full screen. Volume Adjust volume. There are 6 stages from mute to the highest.
provider for help. Tip: While watching TV, pull out the TV antenna to receive better signal. 3.7 Help Click Help icon, and switch to the help interface. Under the help topic, you can get the USB Modem information about function introductions, installation and usage guide, visions and published date of application software and hardware, etc. 3.8 MicroSD card When you use microSD card in the modem, the system will display the MicroSD card as a removable disk. You can use it freely.
4 FAQ & Answers When you meet the following problems in service, please refer to the following answers to solve it. If the problems still exist, please contact with your suppliers. Problem Description The system can not run the installation program automatically. Possible Causes The system configuration is not suitable for the auto run. After the full installation, the system doesn’t install the driver program properly. The system configuration is not suitable for the auto run.
Problem Description Possible Causes 2．You are in the place where no GSM/GPRS/ EDGE/WCDMA/HSDPA network covered , such as underground parking lot, tunnel etc. Problem Solving 2. Change to the places where there is good signal. When the USB Modem has been plugged in, computer cannot find the visual disc of the USB Modem. 1. The installation programs of the USB Modem haven’t been installed properly. 1. Run the installation program first, then insert the modem.
Problem Description Date connection failed. Possible Causes 1. You are in the place where no GSM/GPRS /EDGE/UMTS/HSDPA network covered， such as underground parking lot, tunnel etc. 2. The network at this time in this place is busy now. 3. The APN in the configuration files is error. 4. The modem data is error. 5. The network type selected by manual is wrong. Connected to the Internet, but it cannot open any website page. 1.
Problem Description The Modem cannot connect to the Internet in other places No warning tone My MicroSD card can not read or not found Possible Causes 3. The operating system is infected by virus (Such as Worm Blaster which can take up a quantity of upload data flow and result that it can’t receive downloaded data flow so that you cannot open any website.) 4. You have connected to other APN. which cannot connect to the Internet. Problem Solving 3.
