MF266B Quick Start Guide 1
Scan this QR code to download the Install Helper application.
1. Prepare Installation Tools Prepare the following tools: Crosshead screwdriver Tape measure Marker pens Cutter knife Cable ties Hammer drill Installation Precautions Do not install the device with the interface side facing upwards. Do not install the device horizontally. Do not install the device tilted. WARNING! ZTE is not liable for any problem caused by device falling due to incorrect installation, such as property damage, personal injury or death.
problem caused by the installation in other incorrect directions. Do not install the device at a high position (lightning area). The device must be placed in a well-ventilated environment for use. If possible, install the device in a place with less direct sunlight, for example, in the shade. The device must not be installed at the outlet of the exhaust pipe, or installed in a place where water passes through, for example, a rain shed.
must meet the wind-resistant requirements (not less than level-10 wind speed). The mounting pole should be vertical, and the vertical error should be less than ±2°.
Requirements Installation space requirements 6
Installation medium requirements: Metallic pole.
2. Insert the nano-SIM Card 1. Use the crosshead screwdriver to loosen the two screws and then remove the front cover.
2. Insert the nano-SIM card. WARNING! To avoid damage to the device, do not use any other kind of SIM cards, or any non-standard nano-SIM card cut from a SIM card. You can get a standard nano-SIM card from your service provider.
3. Locate the Installation Position 1. Use a network cable to connect the POE to your device. 2. Connect the POE to the power socket. 3. Check the SIGNAL indicator on your device to find the position. NOTES : Three lights show the signal strength. More lights on means better signals. You also can use the Install Helper Application to help you confirm the signal strength. 4. Locate the position with the best signal strength to install 5. Disconnect the POE and the network cable.
4. Install the Device Install the Device Against a Pole 1. 2. Loosen the clamps. Pass the clamps through the mounting hole and fasten the two clamps to the pole.
Install the Device on a Wall 1. Mark the positions for drilling holes on the wall. The distance between two holes is 58mm.
2. Use a 6mm percussion drill to drill hole at the marked positions and install two expansion bolts. 3. Hang the MF266B on the expansion bolts.
5. Connect a Network Cable 1. Pass a network cable through the waterproof rubber ring, connect to the network port and then wind this cable as shown. 2. Put the cover back and tighten the screws.
6. Connect the POE Adapter 1. Connect the network cable which is from the ODU (MF266B) to the PWR LAN-OUT port on the POE adapter. 2. Use a network cable to connect the LAN-IN port on the POE adapter to the IDU.
7. Check the Installation Device Installation: The MF266B is installed firmly. The network cable is installed firmly. The nano-SIM card is installed. The network ports of the POE adapter are connected correctly. Cables: Verify that all cables are connected properly, cable connectors are secure. Cables should be laid in a clear and straight manner without crossing each other. There is no obvious curve or slant. Cables do not hang in the air or cross each other.
8. Start the Device and Access the Internet Connect the power plug of the POE adapter to the power socket. Your ODU (MF266B) will be powered on and connect to the Internet automatically. And then the IDU which is connected to the POE can access the Internet.
9. Change Your Device Settings You can change the device settings by logging in to the configuration web page. 1. View the label in the packing box to get the default Device 2. Launch the Internet browser. Enter the Device Manager 3. Input the WebUI password and then click Login. 4. After the configuration web page is opened, you can change Manager Website IP address and WebUI password. Website IP address in the Address bar. the password or other settings.
Indicator Lights POWER LAN NETWORK SIGNAL Blue on: Power is on and POE power supply is working normally. Off: Power is off or POE power supply is working abnormally. Blue on: The LAN port is connected. Off: No network cable is connected. Red: The device is turned on but not registered to the mobile network. Blue solid: The device is connected to the 4G LTE network. Green solid: The device is connected to the 2G/3G network. Blue on: Signal level panel. Strength is from weak to strong.
lighted up again to help you check the device status. After the problem is resolved, indicators will be turned off immediately. LEGAL INFORMATION Copyright © 2021 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation.
Warning and Notice Radio Frequency Interference General Statement on Interference Some electronic devices may be susceptible to electromagnetic interference. Locate the device away from TV set, radio and other electronic equipment to avoid electromagnetic interference. Medical Equipment Switch off your wireless device when you are requested to do so in hospitals, clinics or healthcare facilities. These requests are designed to prevent possible interference with sensitive medical equipment.
locations with potentially explosive atmospheres, obey all posted signs to turn off wireless devices. Areas with potentially explosive atmospheres include fueling areas, below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Do not store or transport the device in containers with flammable liquids, gases, or explosives.
Keep your device or its accessories away from sources of heat and fire. High temperature can shorten the life of electronic devices. Do not wrap, seal or cover the device with towels or other objects. Do not use the device in a closed environment such as a box to avoid damage to the device due to poor heat dissipation. Do not allow the device or accessories to come into contact with liquid or moisture at any time. Do not immerse the device in any liquid.
cause an injury or may become detached and create a choking hazard. Accessories Please use original accessories or accessories that are authorized by ZTE. Unauthorized accessories may affect the device performance, damage the device or cause danger to you. Using other types of accessories may void the device warranty, violate the local regulations and laws, and cause an accident. To obtain approved accessories, please contact an authorized service center.
Do not touch the power cable with wet hands, or pull the power cable to disconnect the power adapter. To avoid short circuit, malfunction or electric shock, do not touch the device or power adapter with wet hands. When the power adapter is exposed to rain, liquid or severe moisture, stop using it and contact an authorized service center for inspection. Cleaning and Maintenance The recommended operating temperatures are -40 °C to +55 °C and the storage temperatures are -40 °C to +70 °C.
If any abnormal phenomenon (such as smoke, unusual sound or peculiar smell) occurs, stop using it immediately, disconnect the power adapter, unplug all cables connected to the device, and contact an authorized service center. Do not step on, pull, or excessively bend the device cables. Otherwise the cables may be damaged and the device may malfunction. Before cleaning and maintenance, stop using the device, close all applications, and disconnect all cables connected to it.
household garbage. Please comply with your local laws and regulations regarding the disposal of the device and its accessories. Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. Reasonable abrasion. ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv.
mandatory provisions of the law. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost.
Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance 1.5 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.
