Quick Start Guide

Some features of the product and its accessories described herein rely on the
software installed, capacities and settings of local network, and may not be
activated or may be limited by local network operators or network service
providers, thus the descriptions herein may not exactly match the product or
its accessories you purchase.
ZTE reserves the right to change or modify any information or specifications
contained in this manual without prior notice or obligation.
FCC Regulations:
l This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
l This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
l Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. To comply with FCC RF Exposure compliance
requirements, this grant is applicable to only Mobile Configurations. The
antennas used for the transmitter must be installed to provide a separation
distance of at least 20cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
Step 3 Enter the user name and password, and click Log In.
You can connect to the management web page after the password is
verified.
The default setting is automatically connection and full band
scanning, if you want to connect the LTE network according to your
needs, you can set the connection mode as manual, and simply scan a
specified band.
8 9 10 11 12 13
Step 1 Connect the CPE correctly.
Step 2 Enter the management website.
Step 3 Choose Settings → Wi-Fi → WLAN Settings.
Step 4 In the General Settings area, set Wi-Fi Enable or enable Wi-Fi
with the Wi-Fi button.
Step 5 In the Setting area, change the SSID, such as:
"LTE-Router"
Configuration Wi-Fi
Using a browser to access the management web page to configure and
manage the CPE.
The following procedure describes how to use a computer running
Windows 7 and Internet Explorer to connect to the CPE webpage.
Step 1 Connect the CPE correctly.
step 2 Start Internet Explorer, go to http://192.168.8.1 in the address
bar,
and press Enter.
Login to the Management page
Configure the CPE
Step 1 Connect the CPE correctly.
Step 2 Enter the management website.
Step 3 Choose Settings → Network → LTE Settings.
Step 4 Set the connection mode and scan mode.
Configuration of LTE
· Make sure that the power cable is connected to the PoE, and the CPE is
connected to the right port of the PoE.
· Make sure that the power adapter and PoE are compatible with the
CPE.
The POWER indicator does not turn on.
Frequently Asked Questions
Notice
· Make sure that the CPE is started.
· Verify that the CPE is correctly connected to the computer through a
network cable.
If the problem persists, contact authorized local service suppliers.
· Check that the power adapter and PoE have have connected to the CPE
properly.
· Check that the CPE is placed in an open area that is far away from
obstructions, such as concrete or wooden walls.
· Check that the CPE is placed far away from household electrical
appliances that generate strong electromagnetic field, such as
microwave ovens, refrigerators, and satellite dishes.
If the problem persists, contact authorized local service suppliers.
· The CPE is reheated after being used for long time. Therefore, you must
turn off the CPE when not you are using.
· Check that the CPE is properly ventilated and protected from direct
sunlight.
Fails to Log in to the web management page.
The CPE fails to search for the LTE network.
The CPE power adapter has overheated
· If the CPE powers off unexpectedly while being configured, the
parameters may be restored to the default settings.
· After configuring the parameters, download the configuration file to
quickly restore the CPE to the desired settings.
The parameters are restored to default values.
LTE Settings
Status
DL MCS
UL MCS
DL Frequency
UL Frequency
Bandwidth
RSSI
RSRP0
RSRP1
RSRQ
SINR
TX Power
28
0
3560.0 MHz
3560.0 MHz
20 MHz
-44 dBm
-70 dBm
-72 dBm
-5 dB
32 dB
6 dBm
Settings
Status
Connect Method
Connected
Submit Cancel
Auto
Step 6 To ensure data security, it is recommended that you change the
Wi-Fi password by default.
Step 7 Click Submit to save the settings.
WLAN Settings
General Settings
SSID Profile
SSID
Enabl e
Maximum number of
devices
Hide SSID boradcast
AP isolation
Security
Show password
Password
16
Enabl e
WPA2-PSK
Enabl e
Band
WLAN
Mode
Channel
Tx Power
2.4GHz
802.11b/g/n(Auto)
Auto
100%
Enable
ENTEL-HOGAR-8D6B_2.4G
*
*
IP address
Note: terminal equipment cable outlet must be installed downward
direction.
3. If the diameter of pole is between Φ25mm and Φ30mm, it’s needed
to use the rubber C-type rings to add the diameter of the pole.
2. Using a screwdriver to lock the metal hose clamps, fixed terminal
equipment. Adjust the terminal equipment to align the direction of the
base station for the best effect.
Using a screwdriver to lock
the metal hose clamps
pole type mounting B
C-type ring
When set up the Outdoor Unit, the LEDs of Router will have the
following behavior.
LED Behavior
State Description LED Behavior LED illustration
Signal Strength
weak
Signal strength is weak
Only first signal LED steady
on, the other three off
Signal Strength
medium
Signal Strength is medium
The first two signal LEDs
steady on, the last two off
Signal Strength
good
Signal strength is good
The first three signal LEDs
steady on, the last one off
Signal Strength
strong
Signal strength is strong
All signal LEDs steady on
LTE Scanning
The CPE is searching for a
frequency channel or is
performing network entry
All signal LEDs blinking
simultaneously
LAN Connected
The CPE has a successful
connection with a device
on the LAN
The ETH LED On
LAN
Disconnected
The CPE does not have an
Ethernet connection with
the LAN
The ETH LED Off
SIM card
abnormal
The SIM Card in
abnormal state
The SIM LED Blinking
No SIM card
The SIM Card is
Undetected
The SIM LED Off
SIM card
normal
The SIM Card is ready
The SIM LED On
SYS linked
The CPE attached to LTE
network
The SYS LED On
SYS no link
The CPE not attached to
LTE network
The SYS LED Off
CPE Operation
The CPE is operating
properly
The RUN LED Blinking
Firmware
Upgrading
The CPE is upgrading the
firmware
All signal LEDs scrolling
blink one by one