MF253 Let’s go Getting started with your device. ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.
Connecting Your Device Follow the number to connect your device. NOTES: If you want to use the mobile network to connect to the Internet or use your home phone, you need insert your (U)SIM card first. If you select the different operation mode, the connection of the LAN port is different. Please refer to the chapter “Accessing the Internet” Your device does not support Micro/Nano or any other nonstandard SIM cards. To avoid device damage, please do not use them.
Indicator SIG 3G/4G LAN State Description Blue ON Signal strength is very good or good. Blue Blinking Signal strength is weak. OFF There is no signal. Red The device is turned on but not registered to the mobile network. Blue Blinking The device is connected to the LTE network and data is being transferred. Blue Solid The device is registered to the LTE network. Green Blinking The device is connected to the 3G network and data is being transferred.
3. Select Internet Protocol (TCP/IP), and then click Properties. 4. Select the two items indicated in the following figures, and then click OK to finish the configuration.
Accessing the Internet Before accessing the Internet, please make sure that the following operations are finished. Your device is connected via a network cable or Wi-Fi. Your PC is configured. To access the Internet: 1. Log in the 4G CPE Page. 1) Launch the Internet browser and enter http://192.168.0.1 in the address bar. The login page appears. 2) Input the password and then click Login. The default password is admin. 2.
For Bridge You need to connect the WAN to the LAN port via Ethernet cable and set the clients to obtain the IP address automatically. Your clients can obtain the IP address from the WAN DHCP host and connect to the Internet directly. NOTE: If you want to change the operation mode, you need to set the client a fixed IP address between 192.168.0.100 and 192.168.0.200, and then log in the 4G CPE page to change it.
NOTE：Your service provider gives you the static address information. DHCP mode Please select DHCP and then click Apply. NOTE：Your service provider does not give you any parameters. For Wireless Broadband If you want to use your PC to connect to the Internet, please connect your PC to the LAN port via Ethernet cable. Select Settings > Network Settings > Dial-up Settings to change the WAN connection mode. The default WAN Connection Mode is Automatic.
5. Begin to enjoy your Internet service. Voice Function Making a Call You can make a call through (U)SIM card. To make a call: 1. Pick up the handset. 2. Key in the telephone number. 3. You can either press # key on the telephone to send the call, or wait 4～8 seconds for the call to be connected automatically. 4. The call will be connected. NOTE: If there is no 3G indication, the RF signal is unavailable. Change the location of the router and make sure nothing is blocking it.
WPS Function Your device supports WPS function. You can use this function to connect the client to your device. 1. Power on your device, and enable the Wi-Fi function on your device. 2. 3. 4. 5. Enable WPS function. Please check the WPS Setting on the 4G CPE page. Press the WPS button on your device to start Wi-Fi Protected Setup authentication process. Enable the WPS function on your client to respond this authentication process. Follow the system prompts on your client to finish the connection.
NOTE: Please set the client to obtain an IP address automatically, and the client will get an IP address like “192.168.0.101”. 3. Select the SSID of your device, and then click Connect. NOTE: Please check the label on your device to get the default SSID. 4. Input the password and then click Connect. NOTE: You may need to input the password for Wi-Fi connection. Please check the label on your device to get the default password. 5.
Troubleshooting Voice Related Problems Symptoms Possible Problems/ Solutions No Dial Tone Please wait for 1~2 minutes after the router is turned on. If SIG LED light is blinking, you have no good RF reception. Change the location of the router. There is a prompt/ phone alert/ announcement as soon as I lift the phone off the hook. The line is noisy/ distorted when I lift the phone off the hook. Make sure your (U)SIM card is inserted correctly and the PIN number has been entered.
Others Symptoms Possible Problems/ Solutions The 3G/4G signal indicator is always blinking or does not light. This indicates poor reception. Try moving the router to another location near the window. For the Wi-Fi connection password, please check the label on the device. The default password of the 4G CPE page is admin. About the password 12 If you changed the password and forgot the new password, you need to restore the device to the factory default settings.
Warning and Notice Safety Precautions Some electronic devices may be susceptible to electromagnetic interference. Locate the router away from TV set, radio and other electronic equipment to avoid electromagnetic interference. The router may interfere with medical devices like hearing aids and pacemakers. Consult a physician or the manufacturer of the medical device before using the router. Please keep yourself at least 20 centimeters away from router.
iii. End User’s mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the Product. iv. Modifications or repairs not made by ZTE or a ZTE-certified individual. v. Power failures, surges, fire, flood, accidents, actions of third parties or other events outside ZTE’s reasonable control. vi. Usage of third-party products, or usage in conjunction with third-party products provided that such defects are due to the combined usage. vii.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
