Operation Manual © 2015 ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited.
Contents Introduction Introduction ……………………………… 2 Playback ……………………………… 13 Usage and Safety Precautions ……… 3 Connecting MIDI Devices …………… 15 Part Names ……………………………… 4 Restoring Factory Default Settings Connecting with a Computer ………… 6 Troubleshooting ……………………… 17 iPad connection (class compliant mode)………………… 8 Specifications ………………………… 18 16 Recording ……………………………… 10 Introduction 2-in/2-out USB3.0 Audio Converter The is an audio converter with a SuperSpeed USB3.0 interface.
SAFETY PRECAUTIONS In this operation manual, symbols are used to highlight warnings and cautions that you must read to pre vent accidents. The meanings of these symbols are as follows. Volume Do not use at a loud volume for a long time.
Part Names Part Names Top Panel Level indicators GAIN knobs PHONES knob Power indicator INPUT 2 jack Hi-Z switches INPUT 1 jack PHANTOM switch XLR 2 4 3 OUTPUT knob PHONES jack TRS 1 TIP : HOT 1 : GND 2 : HOT 3 : COLD RING : COLD SLEEVE : GND
POWER switch DIRECT MONITOR switch Part Names Rear Panel USB 3.
Connecting with a Computer Connecting with a Computer Installing the Driver Do not connect the 1. until installation completes. Download the ZOOM UAC-2 Driver from http://www.zoom. co.jp/downloads/ to your computer. NOTE t :PV DBO EPXOMPBE UIF MBUFTU ;00. 6"$ %SJWFS GSPN UIF BCPWF XFCTJUF t %PXOMPBE UIF ESJWFS GPS UIF PQFSBUJOH TZTUFN UIBU ZPV BSF VTJOH 2. Launch the installer and install the driver. 'PMMPX UIF JOTUSVDUJPOT UIBU BQQFBS PO TDSFFO UP JOTUBMM UIF ;00.
Before turning the power on, minimize the volumes of the connected devices. 1. Use a USB cable to connect the and and the computer. NOTE Connecting with a Computer Turning the Power ON t Although also compatible with 64# 64# DPOOFDUJPO enables operation with even higher performance. 2. Set to ON. NOTE t 5IF cannot be used if it is not connected to a computer.
iPad connection (class compliant mode) iPad connection By using the optional power adapter for this unit (AD-14), you can connect it to an iPad. 1. Set to ON. NOTE t 5VSO UIF QPXFS 0'' CFGPSF DIBOHJOH UIF $-"44 $0.1-*"/5 .0%& TXJUDI TFUUJOH If the power is already ON, changing the CLASS COMPLIANT MODE switch will have no effect. 2. Plug the AD-14 adapter designed for this unit into an outlet.
Connect the and the iPad using an Apple iPad Camera Connection Kit or Lightning to USB Camera Adapter. 4. Set After the to ON. iPad connection 3. turns on, it will connect to the iPad.
Connecting Instruments Connect instruments to INPUTS 1/2 using TRS/mono phone cables. Recording Keyboard Connecting Instruments (TRS cables) Guitar Bass guitar (mono phone cable) Using the Hi-Z Function t 8IFO DPOOFDUJOH B QBTTJWF HVJUBS PS CBTT HVJUBS UP an INPUT, press its so that it lights. t 8IFO DPOOFDUJOH B LFZCPBSE PS PUIFS JOTUSVNFOU UP an INPUT, press its so that it becomes unlit.
Connecting Mics Using XLR cables, connect mics to INPUTS 1/2. Recording Dynamic mic Condenser mic (XLR cable) Connecting Mics (XLR cable) Using Phantom Power t 8IFO DPOOFDUJOH B DPOEFOTFS NJD QSFTT so that it lights. Phantom power is supplied when this switch is lit.
"EKVTUJOH *OQVU (BJO You can adjust the gain of each INPUT. Recording 1. Check the status of the input signal. Lit green: Input signal present. Lit red: Input signal is clipping. "EKVTUJOH *OQVU (BJO 2. Adjust the input gain. Turn the .
Connecting Headphones and Speakers 1. Headphones Speakers Adjust the headphones/speakers volume. Headphones volume: Turn . Speakers volume: Turn . Connecting Headphones and Speakers 2. Connect headphones or speakers. Playback Connect headphones to the PHONES jack and speakers to the OUTPUT jacks. Then, adjust the volume.
Using Direct Monitoring Playback Using Direct Monitoring 14 Sound inputs into the can be directly output without passing through the computer. This enables monitoring without latency. 1. Set the . Direct monitoring setting INPUT 1 jack MONO Output from the PHONES jack and both L/R OUTPUT jacks. INPUT 2 jack STEREO Output from the PHONES Output from the PHONES jack and the L OUTPUT jack. jack and the R OUTPUT jack. OFF This disables direct monitoring.
Use MIDI cables to connect MIDI devices to the MIDI IN and MIDI OUT jacks. MIDI keyboard, MIDI controller MIDI OUT jack Sound module MIDI IN jack MIDI OUT jack Connecting MIDI Devices Connecting MIDI Devices MIDI IN jack NOTE t 8IFO VTJOH B .*%* QPSU XJUI B %"8 GPS FYBNQMF GPMMPX UIF JOTUSVDUJPOT CFMPX XIFO making settings. The or might not function properly otherwise. Windows 6TF ;00. 6"$ .*%* %P OPU VTF .*%* */ 065 ;00. 6"$ .*%* Mac 6TF ;00. 6"$ .
Restoring Factory Default Settings 16 Restoring Factory Default Settings Follow these instructions to initialize settings, restoring them to their factory defaults. 1. Turn the power ON while pressing 2. Initialize the settings. Execute: Press . Execute Cancel: Press . Cancel . (→P.
Troubleshooting t Confirm that the computer correctly. device is connected to the t Quit all the software that is using the , and disconnect and reconnect the USB cable . connected to the t Reinstall the driver. t Connect the directly to a USB port on the computer. Do not connect it to a USB hub. Playback sound cannot be heard or is quiet t Check the speaker connections and volume settings on the speakers. t A djust the O U T P U T and P H O N ES volume controls.
Specifications Specifications 18 9-3 534 DPNCP KBDLT 9-3 IPU 534 5*1 IPU 0–60 dB (in 1dB steps) 5 kΩ 1 MΩ (when Hi-Z ON) Maximum input level E#V BU E#'4 Phantom power +48V Outputs OUTPUT Connector TRS jack (balanced) L/R Maximum output level +14 dBu (at 0 dBFS) Output impedance 100 Ω PHONES Connector Standard stereo phone jack N8 ¨ JOUP û MPBE Maximum output level +8 dBu (at 0 dBFS) Output impedance û Frequency characteristics "U L)[ ¦ E# )[ o L)[ "U L)[ ¦ E#
FCC regulation warning (for U.S.A.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Included items The package should contain the following items. Please confirm that they have all been included. USB 3.
