Specifications
◆
TOTAL module
ZOOM GFX-5
34
◆
TOTAL module
The TOTAL module is not an independent effect module. It serves to set parameters that affect all patches.
TYPE 4: MN-DLY (Mono delay)
This is a monaural delay with a duration of up to 1.5 seconds.
TYPE 5: PP-DLY (Ping-Pong Delay)
When two amplifiers are used, this serves as a ping-pong delay effect with a duration of up to 1.5 seconds. When one amplifier is used, the
effect is a mono delay.
* Parameters for TYPE 4 and 5 are the same.
Parameter 1 TIME Parameter 2 FB Parameter 3 MIX
1 – 99, 1.0 – 1.5,t1 – t9 0 – 10
0 – 30
Adjusts delay time from 10 ms to 990 ms in
10-ms steps (1 - 99), and over 1 second in
100-ms steps (1.0 - 1.5). t1 - t9 select a
particular note using the rhythm pattern
tempo as reference (see table below).
Adjusts number of repeat cycles (feedback)
for delay sound.
Adjusts delay sound level.
[TIME parameter ]
t1: half note t2: dotted quarter note t3: quarter note t4: dotted eighth note t5: half triplet note
t6: eighth note t7: dotted sixteenth note t8: quarter triplet note t9: sixteenth note
TYPE 6: DLYHAL (Delay + Hall Reverb)
This is a combined delay and hall reverb effect.
TYPE 7: DLYROM (Delay + Room Reverb)
This is a combined delay and room reverb effect.
* Parameters for TYPE 6 and 7 are the same.
Parameter 1 DLYTIM Parameter 2 DLYMIX Parameter 3 REVMIX
1 – 50,t1 – t9
0 – 15
0 – 15
Adjusts delay time in 10-ms steps. t1 - t9
select a particular note using the rhythm
pattern tempo as reference (see table above).
Adjusts delay sound mix. Adjusts reverb sound mix.
TYPE 8: HLDDLY (Hold Delay)
This is a hold delay effect that lets you record a phrase of up to 2 seconds during a performance and play it back
repeatedly. (For details, see page 23.)
Parameter 1 TIME Parameter 2 MODE Parameter 3 MIX
1 – 99, 1.0 – 2.0, Mn nL, So, rS 0 – 30
Adjusts recording time. (For settings, see
page 23.)
Selects playback mode for recorded phrase.
Settings are nL (normal direction playback),
So (Sound-on-sound), and rS (reverse
direction playback).
Adjusts effect sound mix.
Parameter 1 PATLVL Parameter 2 MINVOL Parameter 3 R-MODE
1 – 30 0 – 10 UP, dn, Hi, Lo
Sets final patch level. A setting of 25 means
that input signal and output signal levels are
equal.
Sets the minimum value when using
expression pedal as volume pedal.
Selects expression pedal action range. (For
details, see page 22.)
Parameter 4 R-WAVE Parameter 5 R-SYNC Parameter 6 Patch name
1 – 9 0 – 3, b1 – b4
Available characters are listed below.
Selects control waveform type. (For details,
see page 21.)
Sets control waveform cycle. (See table
below.)
Use PARAMETER [Q]/[W] keys to select
input position, and turn [VALUE] dial to
select character.
[R-SYNC parameter ]
0.5: eighth note b1: 1 measure
1: quarter note b2: 2 measures
2: half note b3: 3 measures
3: dotted half note b4: 4 measures
[Available characters]
' ( ) * + - / 0 1 2 3 4 5 6
9 < = > ? @ A B C D E F G
L M N O P Q R S T U V W X
78
HIJK
Z\Y
(Space)
(Space)
ZOOM GFX-5
35
Troubleshooting
■
No sound, or very low volume
• Is the power switch set to ON?
•Are [INPUT] jack and [OUTPUT] jack connected
correctly to instrument and amplifier?
• Is the shielded cable defective?
• Is GFX-5 set to mute condition?
• Is [LEVEL] knob turned down?
• Is expression pedal raised?
For some patches, the expression pedal controls the volume.
Set it to a suitable position.
■ Cannot record from [AUX IN] jack
• Is input source set to "GT"? Set it to "AUX".
■ Sound is unnaturally distorted
• Adjust level and gain parameters of effect
modules.
• Set [TURBO] key and [EDGE] key to OFF.
• Set BOOSTER or ISO/COMP module to OFF.
When a guitar with high output is used with the above
effects, unwanted distortion may occur depending on the
DRIVE module effect type.
■ High noise levels
• Adjust ZNR parameter. If problem persists, try
reducing GAIN.
If BOOSTER or ISO/COMP module is used, try decreasing
GAIN parameter of DRIVE module.
■ Cannot play rhythm pattern or volume is
very low
• Is rhythm volume set to low value?
Increase LVL parameter to suitable setting.
■ Expression pedal on/off switching does
not work properly.
•Try the procedure described in "Calibrating the
Expression Pedal" on page 26.
■ Bypassed sound is unnatural
• The Energize works also in the bypass condition.
Set the Energize to "oF."
Specifications
Effect Programs 74 types
Effect Modules 8 modules
Patch Memory USER: 60 patches
PRESET: 60 patches
Total 120 patches
Sampler 16-bit linear recording/playback
Maximum recording time 6 seconds
Sampling Frequency 31.25 kHz
A/D Conversion 20-bit, 64-times oversampling
D/A Conversion 20-bit, 8-times oversampling
Inputs
Guitar input Standard mono phone jack
Rated input level -20 dBm
Input impedance 470 kilohms
AUX input Miniature stereo phone jack
Rated input level -20 dBm
Input impedance 20 kilohms
Outputs
Line output 2 x standard mono phone jacks
Maximum output level +3 dBm
Output load impedance 10 kilohms or
higher
Headphone output Standard stereo phone jack
50 mW into 32 ohms load
Display 6-digit alphanumeric LED display
2-digit 7-segment LED display
Power Requirements
AC adaptor 9 V DC, center minus, 300 mA
(ZOOM AD-0006)
Batteries 4 x IEC R6 (size AA)
Continuous operation: approx. 10
hours (with alkaline batteries)
External Dimensions
390 (W) x 220 (D) x 75 (H) mm
Weight 2.8 kg (without batteries)
* 0 dBm = 0.775 Vrms
* Design and specifications are subject to change without notice.