Wireless-N Router USER MANUAL
NOTICE This document contains proprietary information protected by copyright, and this Manual and all the accompanying hardware, software, and documentation are copyrighted. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
MENT Contents Contents ........................................................................................................................3 Installing the Wireless-N Router ................................................................................5 Package Contents .................................................................................................. 5 System Requirements............................................................................................
Configuring Basic Settings ......................................................................... 41 The Basic Setup Page.................................................................................. 42 Using your 3G modem as a Backup ........................................................... 44 The DHCP Server Page............................................................................... 45 The Wireless Setting Page ..........................................................................
1 Installing the Wireless-N Router Package Contents The package contains the Zoom Wireless-N Router, an RJ-45 Ethernet cable, a 5V 1.2A Power adapter, a Quick Start installation flyer, and a CD that contains additional documentation and warranty information. If anything is missing or damaged, please contact Zoom Customer Support or whoever provided the Wireless-N Router. System Requirements Any DSL or cable modem or modem/router that has an Ethernet port should work with the Wireless-N Router.
Connecting a Smartphone or a Tablet to Your Router If you are using the router with a mobile broadband USB modem please go to Connecting a Modem or non-Android Smartphone or Tablet to Your Router. If instead you are using a smartphone or tablet with the router, please read the information below before continuing.
this code. If your Router is not working with your Android smartphone or tablet see Troubleshooting your Internet Connection, otherwise go to Chapter 2, Using the Configuration Manager to learn how to: ¾ Enable Wireless Security. ¾ Change the router’s password to prevent users on your network from changing the settings of the Wireless-N Router. ¾ Change other wireless settings such as your Wireless Network Name (SSID) or you wish to disable WiFi access to your router.
5 6 7 on the Task Bar, click Available Wireless Networks, select Zoom from the list of available wireless networks, and then make the connection. The router comes set up for wireless with no security. If you want wireless security, you need to set up the mobile broadband router and each device for the security that you want. To learn how to enable wireless security on your Router, please see Chapter 2, Using the Configuration Manager.
www.zoomtel.com/router/comp for a list of compatible modems and phones. If your device is listed and you are still having trouble, please contact Zoom support as described in Appendix C: Registering Your Product and Getting Help. Resetting the Router to the Factory Configuration In the unlikely event that you need to reset the router to the factory default configuration, insert the blunt end of a paper clip into the RESET hole on the side panel of the router. Hold the clip in place for seven (7) seconds.
2 Using the Configuration Manager Your Wireless-N Router is preset with default values that meet the needs of most users. However, you can change these settings using the router's built-in Configuration Manager. Here are some reasons why you might want to use the Configuration Manager: • You are plugging the wireless-N router into a DSL or cable modem. • You want to set or change some settings of your Router.
5 On the Toolbar, type admin (the default password) in the System Password field, then click Login. 6 By default the configuration manager is set to English. If you wish to change it to Spanish select Español from the drop down box on the Toolbar. When you log in, the Configuration Manager opens its Main Menu. • You should use the Configuration Manger’s Setup Wizard if any of the following apply to you. ¾ You wish to set up a Cable or ADSL modem to work with the Wireless-N Router.
¾ Internet during certain hours. See The Schedule Rule and Schedule Rule Setting Pages on page 67 for more information. You wish to change other wireless settings such as your Wireless Network Name (SSID) or you wish to disable WiFi access to your router. If any of these apply to you, see Launching the Configuration Manager’s Setup Wizard below.
Step 1. Setup Login To view or change configuration settings, you must enter a password. Your router has a default password (admin) that was set by the factory and that you used to access the Configuration Manager initially. If you want to keep the default password, click Next to skip this step. Otherwise, to safeguard your configuration, particularly if you make changes, we recommend that you change the login password. 1 On the Setup Login Password page, type the old password in the Old Password field.
Step 3. WAN Type Setup The WAN Type refers to the protocol used by your Internet Service Provider in establishing your Internet connection. By default, WAN Type is set to your Mobile Broadband USB modem. If that is what you want, you can select Next to skip this section. Selecting the WAN Type Please check with your service provider if you read the discussion below and are still unsure which WAN Type to choose.
mobile broadband modem as the backup to an ADSL or Cable modem, you'll need to use the Configuration Manager's Advanced program to configure this setup. Please refer to Using your 3G modem as a backup on page 44.) You should select your primary connection type using the Setup Wizard. (To access the Setup Wizard, refer to page 12 for instructions.) The relevant section immediately below depends on the WAN Type you selected.
• Static Primary DNS This is the Domain Name System (DNS) server's IP address. Your service provider supplies this address. • Static Secondary DNS This is the IP address of an alternate Domain Name System (DNS) server. Your service provider supplies this address. Go to Step 4. Wireless Settings on page 22. Configuring the Dynamic IP Address The page shown below only appears if you select the Dynamic IP Address button on the Select WAN Type menu. Otherwise skip this section.
that was registered with your service provider for your device. Go to Step 4. Wireless Settings on page 22. Configuring PPPoE The page shown below only appears if you select the PPPoE button on the Select WAN Type menu. Otherwise skip this section. • LAN IP Address This is the LAN IP Address of your router. Devices behind your router use this address as their default gateway. Most users will not need to change this address. • Username This is the PPPoE username supplied by your service provider.
Your service provider supplies this address, if needed. • Service Name This is the name assigned by your service provider to identify your service. The Service Name is optional. • Assigned IP Address This is the optional IP address assigned by your service provider. The Assigned IP Address is optional. Go to Step 4. Wireless Settings on page 22. . Configuring PPTP The page shown below only appears if you select the PPTP button on the Select WAN Type menu. Otherwise skip this section.
• • • • • My Subnet Mask This is the private subnet mask that your service provider assigned to your router. Gateway IP This is the IP address of the service provider's server. Your service provider supplies this address. Server IP Address/Name This is the name and IP address of the PPTP server. Your service provider supplies this information, if needed. PPTP Account This is the PPTP account name that your service provider assigned to you.
• • • • • • dropdown menu, based on your service provider's requirements. IP Address This is the IP address that identifies the L2TP server. Your service provider supplies this address. Subnet Mask This is the router's subnet mask. Your service provider supplies this address. WAN Gateway IP This is the WAN Gateway IP address of the L2TP server. Your service provider supplies this address. Server IP Address/Name This is the name and IP address of the L2TP server.
If you do not know the APN, Dialed Number, Account, or Password of your service provider, you should contact them or refer to Appendix A: Mobile Broadband Settings for a list of many wireless service providers’ settings. You may also want to refer to http://www.zoomtel.com/mbsettings. You may also be able to get the information from looking at your modem or phone’s software. Please refer to the documentation that came with your modem or phone for more information.
Step 4. Wireless Settings The Wireless Settings page lets you configure the wireless settings for your Router and devices. If you are happy to have no wireless security, click Next to go to Step 5. If all of your network's wireless devices are capable of WPS security setup and you want to use WPS, please go to Steps 5 and 6, then exit the Wizard and go to Chapter 3: Wireless and Wireless Security on page 28. Otherwise, continue below.
TIP: Other wireless networks might be within range of your network. Your neighbors, for instance, may be within range. If you are having trouble connecting, try setting a different channel to see if that improves performance. You should try setting a channel that is 5 more than what you are using. By default, the Wireless-N Router is set to 10. You may want to try channel 6 or 1, for instance, if you have trouble connecting with the default channel (10).
WPA-PSK/WPA2-PSK Authentication We recommend this setting if all devices on your network support either WPA or WPA2. Your router will automatically detect whether it should use WPA or WPA2. When you select WPA-PSK/WPA2-PSK from the Authentication dropdown menu, the Encryption field expands, as shown in the following figure. Field Entry Authentication Accept WPA-PSK/WPA2 PSK as the default value.
expands, as shown in the following figure. Field Entry Authentication Select WEP Encryption Select WEP Encryption WEP Key 1, 2, 3, 4 We recommend selecting HEX as the key format as Ascii keys can have compatibility issues between different devices.. Encryption WEP Key 1, 2, 3, 4 You can choose to either use WEP 128 bit encryption or WEP 64 bit encryption. The difference is 128 bit is more secure and 64 bit is faster. We recommend selecting 64 bit.
key in the space below for future reference, and then enter it in the Key 1 box. ————— If you selected ASCII format, and you chose a 128-bit key length, 13 ASCII characters are required. Write the 13-ASCII-character key in the space below for future reference, and then enter it in the Key 1 box. ————————————— Step 5. Summary The Summary page displays the updated configuration settings for your router and lets you accept, change, and test the configured values.
1 2 3 To edit your entries, click Back as many times as needed to access the page for the field(s) to be edited, then click Next to continue with your edits or to return to the updated Summary page. Mobile Broadband: To test the updated configuration on your network, click the checkbox next to Do you want to proceed with the network testing? When you're satisfied with the configured settings, click Apply Settings to save the new configuration. Step 6.
3 Connecting Devices Wirelessly to the Wireless-N Router This chapter assumes that your Wireless-N Router has its wireless security settings set up the way you like them, either with the factory default of “no security” or with a particular type of security as discussed in Chapter 2. This chapter provides tips for connecting devices (computers, phones, tablets, game stations, etc.) wirelessly to the Wireless-N Router.
Connecting a Windows 7 Computer with Built-in Wireless Capabilities 1 From the taskbar, click on the wireless symbol. 2 In the wireless network options box, highlight the Wireless Network Name (SSID) you gave your wireless network in Step 4 of the Setup Wizard. If you did not change the Wireless Network Name (SSID), select the default name Zoom. If you want to automatically connect to the Wireless-N Router, click the Connect Automatically box. Then click Connect.
Connecting a Windows Vista Computer with Built-in Wireless Capabilities 1 From the Start menu select Connect to. 2 In the Connect to a network dialog box, highlight the Wireless Network Name (SSID) you gave your wireless network in Step 4 of the Setup Wizard. If you did not change the Wireless Network Name (SSID) select the default name Zoom and click Connect. • If your desired network is secured, in the next dialog box enter the security key or password and click Connect.
Connecting a Windows XP Computer with Built-in Wireless Capabilities 1 2 On your Windows desktop, click the Wireless Network Icon in the System Tray. Windows will automatically scan for available wireless networks in your area. Any compatible networks within range will appear in the Available networks list. Double-click the Wireless Network Name (SSID) you gave your wireless network in Step 4 of the Setup Wizard. If you did not change the Wireless Network Name (SSID), select the default name Zoom.
select the default name Zoom. • If you enabled security in Step 4 of the Setup Wizard, enter the wireless security key you created in Step 4 when you are prompted for the password in the next dialog box. Click OK to connect to your router. ¾ More than one wireless network may appear in the list. These are other wireless networks that are within range of your network. Your neighbors, for instance, may be within range of your network. Each wireless network has a channel associated with it.
how to log in to the Zoom Configuration Manager, see page 10. After logging in, select Wireless from the left-hand menu. On the Wireless page you can select a new channel from the drop-down menu. 2 Test your wireless connections. From each computer or device that you set up, open your Web browser (for instance, Internet Explorer, Firefox, or Chrome) and try to connect to a familiar Web address.
with it. We recommend there be at least a five-channel difference between your network and those of your neighbors. Having less than a five-channel difference may result in interference with your connection. By default, the Wireless-N Router uses channel 10. If you need to change this channel, you must do so using the Wireless Setup page of the Zoom Configuration Manager. For instructions on how to log in to the Zoom Configuration Manager, see page 10.
3 Refer to your client device's documentation for further instructions, if necessary. Method Two Use this method if your client device already has a WPS PIN number. The client is the Enrollee. 4 If you haven't already done so, open a Web browser and type http://192.168.2.1 in the address bar. a When the Configuration Manager launches, log in as admin, then select Advanced > Basic Settings > Wireless to open the Wireless Setup page. b Click the WPS Setup button to open the Wi-Fi Protected Setup page.
4 Configuring Wireless Security Manually Note: Most users will not need to read this chapter. Most users either use the Wireless-N Router’s default settings (“no wireless security”) or use the Setup Wizard described in Chapter 2 to set wireless security. We recommend you set WPA2/WPA security unless you know that you will be connecting devices to your network that support only WEP. If you know you have some devices that only support WEP, go to WEP Configuration on page 40.
5 In the Authentication drop down bar select WPA – PSK/WPA2 – PSK. If you know all your devices support WPA2-PSK you can select it instead. 6 In the Security Key field enter a value for the key. The maximum value is 64 characters. The minimum value is 8 characters. 7 Write down the wireless security key and put it where you can find it – on the bottom of the Wireless-N Router case, for instance. 8 Click Save.
http://192.168.2.1 and then press Enter. When the MAIN MENU opens for the first time, it displays a System Status page that summarizes the current settings and values for your system. 38 3 On the Toolbar, type admin (the default password) in the System Password field, then click Login. 4 When you log in, the Configuration Manager opens. Select Advanced from the Administrator’s Main Menu bar then click Wireless on the left hand menu. 5 In the Encryption drop down bar select WEP.
9 Now you need to set up each of your wireless devices with the Key that you entered. See Establishing your Wireless Network on page 28 for instructions on connecting devices to the Wireless-N Router.
5 Using the Configuration Manager's Advanced Program Most users will not need to manually set up their router. In the unlikely event that you do, you can use the Configuration Manager's Advanced program to change the router's default settings.
¾ You want to back up router settings that you made using the Configuration Manager. See The Backup Setting Dialog on page 71 for details. Online Help The Advanced program provides both online and context-sensitive help that guides you in changing the settings on each menu. ¾ To access online help, click [HELP] on the menu's Toolbar. Each [HELP] page describes the fields on the active page and, when applicable, the required or recommended entries.
provides a description of the configuration menus at center. The Basic Setup Page You can use the Basic Setup page to configure your LAN and WAN setup. Note: The following image depicts the fields that the program displays when 3G is selected as the WAN Type. The fields will differ for each WAN Type. See the online help for a description of each WAN Type and its corresponding fields. If you want to use a 3G modem as a backup to your cable or ADSL modem, go to Using your 3G modem as a backup on page 44.
LAN IP Address The local IP address of the router. 192.168.2.1, by default. All wireless or wired devices on your network must use the LAN IP address of your router as their default gateway. 3G Failover See Using your 3G modem as a backup on page 44 for instructions on using 3G Failover. WAN Type Set to LTE / 4G / 3G, by default. You can choose another option from the dropdown menu, based on the WAN connection type that your service provider supports.
to http://www.zoomtel.com/mbsettings. Authentication Set to Auto, by default. Optionally, click Password Authentication Protocol (PAP), or Challenge Handshake Authentication Protocol (CHAP), if supported by your service provider. Primary DNS and Secondary DNS IP address of the Domain Name Servers. These addresses are provided by your service provider. Connection Control Specifies the method for connecting or disconnecting the WAN session based on network activity. Auto Reconnect (always on) is the default.
c From the Configuration Manager, click on Advanced and then Basic Setup and paste the IP address into the Internet host textbox. 5 Click Save. The DHCP Server Page You can use the DHCP Server page to configure your DHCP server. If you want to change the default values, please click [HELP], which opens a page that describes each item and the recommended values. The Wireless Setting Page You can use the Wireless Setting page to configure your wireless LAN setup.
Wireless Module Accept the default, Enable. Click the Disable checkbox only if you do not want wireless clients to access your network. Wireless Network Name(SSID) Refers to the Service Set Identifier for your device. By default, the SSID for the Wireless-N Router is Zoom. You can change the SSID to a name of your choice. The SSID can be up to 32 alphanumeric characters. If you change the name, make sure that all devices on your network use the new SSID as the access point.
For WEP Authentication: You can accept the default, WEP-Auto or select one of the available options. Select WEP-Open to use Open System authentication. Select WEP-Shared to use Shared Key authentication. For WPA-PSK/WPA2-PSK Authentication: You can select WPA-PSK/WPA2 PSK if your devices support both authentication methods. Optionally, select WPA-PSK or WPA2-PSK if all devices on your network support only one of these authentication methods.
If you selected ASCII format, and you chose a 64-bit key length, 5 ASCII characters are required. Write the 5-ASCII-character key in the space below for future reference, and then enter it in the Key 1 box. ————— Click WPS Setup to launch the WiFi Protected Setup (WPS) Setup program. For instructions, please refer to WPS Configuration on page 34. The Change Password Page You can use this page to change your login password. To view or change configuration settings, you must enter a password.
Port triggering works by sensing when data is sent out on the predetermined outgoing port and then automatically opening up the corresponding incoming port(s). It will automatically forward the traffic on the incoming port to the computer that accessed the outgoing port. If your game uses one port to send outgoing data and a different port (or ports) for incoming data, you may want to use port triggering.
A virtual server will allow access to your computer on certain ports. A port is like a channel that is used by applications (such as games) to communicate on. For example, the directions for the game you want to play over the Internet might tell you to open port 6000. Common Services This drop down menu lists some common games and applications. If your game or application is on the list select it as well as the next open ID. Click Copy to and the router will configure the Virtual Server settings for you.
Click to enable the Virtual Server Use Rule# You can enable your virtual server for certain periods of time by assigning it a Rule #. You must first set up the appropriate Scheduling Rule. See The Schedule Rule and Schedule Rule Setting Pages on page 67 for more information. For example, if you have an FTP server (port 21) at 192.168.1.5, a Web server (port 80) at 192.168.1.6, and a game that requires port 5000 to be open at 192.168.1.7, then you need, at minimum, to specify the following mapping.
Incoming Ports When the trigger packet is detected on the outbound port, the inbound packets sent to the specified port numbers are allowed to pass through the firewall. Enable Enables access for the specified application. Popular applications Provides a menu of applications from which to choose. Select an application and click Copy to to add the application to your list. Click Save to store your selection or Undo to remove the entry.
The Miscellaneous Page The Miscellaneous Page lets you set up and enable a DMZ Host on your network, and enable UPnP settings for software and devices. In this way, specific ports can open for incoming traffic that must pass through your firewall. You can also enable IGMP on this page in the unlikely event that your service provider is using it. Set IP Address of DMZ Host A DMZ (Demilitarized Zone) Host is a host without the protection of the firewall.
Configuring Security Settings The Security Setting page lists the configuration menus on the left pane and provides a description of the configuration menus at center.
Status Page The Status page shows you the status of the inbound and outbound Packet Filters and the Domain Filters. Inbound, Outbound, and Domain filters are disabled, by default. Packet Filtering Page Packet Filtering allows you to control what packets are allowed to pass through the router. Outbound Packet filters control outbound packets and Inbound Filtering controls packets coming from the Internet. Inbound Filters applies only to packets going to a Virtual Server or DMZ.
Filtering Policies You can select one of the two filtering policies: Allow all to pass except those that match the specified rules Deny all to pass except those that match the specified rules Filtering Rules You can specify eight rules for each direction: inbound or outbound. For each rule, you can define the following: Source IP address Destination IP address Destination Port Use Rule# For the Source or Destination IP address, you can define a single IP address (4.3.2.1).
The Domain Filters Page You can use the Domain Filters page to enable or deny user access to specified URLs. Domain filtering and URL Blocking perform similar functions. The major difference between Domain Filtering and URL Blocking is that Domain Filtering requires the user to input a suffix whereas URL Blocking requires the user to input a keyword only. In other words, Domain Filtering can block a specific web site, whereas URL Blocking can block hundreds of web sites by specifying a keyword.
The action to be taken when a user accesses the restricted domain suffix URL. Check Drop to block access. Check log to record the attempted access. Enable Click the checkbox to enable a rule. The URL Blocking Page You can use the URL Blocking page to block LAN computers from connecting to pre-defined Web sites or to limit their access to specific websites.
example, if you set up blacklisting, you can use the pre-defined word, sex, to block all website URLs that contain the pre-defined word, sex. Enable Click the checkbox to enable each rule. The MAC Address Control Page You can use the MAC Address Control page to provide an added layer of security to your Wireless-N Router. MAC Address control is used to define connection and association rights for clients whose IP and MAC addresses are specified.
Association control Check Association control to specify which wireless clients can associate to the wireless LAN. If a client is not allowed to associate to the wireless LAN, then the client can't send or receive any data via this device. Choose allow or deny to indicate which clients can associate to the wireless LAN. If selected, the specified wireless client will obtain any radio connection to the access point. DHCP clients Displays a list of computers that are currently connected to the router.
Configuring Advanced Settings The Advanced Settings page lists eight menus on the left pane and provides a description of the configuration menus at center.
The System Log Page You can use the System Log page to define how and where system logs will be exported via syslog (UDP) or SMTP(TCP). IP Address for Syslogging Host IP address of the destination where the Sys log will be sent. Click the Enable checkbox to set the IP Address as the destination. E-mail alert settings Check Enable if you want to send syslog via email. SMTP Server IP and Port Input the SMTP server IP and port; for example, mail.your_url.com or 192.168.2.100:26.
The Dynamic DNS Page You can use the Dynamic DNS page to define the Dynamic Domain Name Service (DDNS) that will host your server. For example, the DDNS could host your server when you want to host a website on your network but you do not have a static IP.
QoS Control Click the Enable checkbox to enable QoS. Available Upstream bandwidth Set the upstream speed. The best way to find your throughput is to use one of the free speed tests widely available on the Web. Some examples of sites with good speed tests are www.speedtest.net and www.speakeasy.net/speedtest. When you now your actual upstream throughput, enter it in this field. The value should be in kilobits per second (Kbps). Local: IP Define the local IP address of packets.
level set. For critical applications, select High or Normal. For non-critical applications, select Low. High is the default value. Enable Click the Enable checkbox to apply the settings. User Rule# Select a rule from the dropdown menu to indicate when the policy applies. (0) Always is the default value.
Select the SNMP Version that your SNMP Management software supports. WAN Access IP Address Enter the IP address for WAN access. The Routing Table Page You can use the Routing Table page to enable/disable both Dynamic and Static Routing. If routing is enabled, you can specify which physical interface address to use for outgoing IP data grams.
The System Time Page You can use the System Time page to set and synchronize your router with the local time zone, the Time Server and your PC. Time Zone Select the local time zone from the dropdown menu. Auto-Synchronization Click the Enable checkbox to enable this function. Select an item from the Time Server dropdown menu to specify the server with which to synchronize. The default value is Auto. Click Sync with Time Server to set Date and Time by NTP Protocol.
The Schedule Rule and Schedule Rule Setting Pages You can use the Schedule Rule and Schedule Rule Setting pages to define when services will be turned on and off based on rules that you define. 1 On the Schedule Rule page, click the Enable checkbox to enable the scheduling rules, which are defined on the Schedule Rule Setting page. a. Click New Add to open the Schedule Rule Setting page.
b c On the Schedule Rule Setting page, specify a Rule name, a Policy that defines whether the rule is Active or Inactive, Week Day and the Start Time and End Time for each rule that you are creating. Click Save for each rule that you create. d Click Back to return to the Schedule Rule page. e When the Schedule Rule page opens, the rule(s) that you created and saved appear in the Rule Name column. You can click Edit to make changes to a scheduled rule or click Delete to remove a scheduled rule.
Configuring Toolbox Settings The Toolbox Settings page lists six configuration menus on the left pane and provides a description of the configuration menus at center. The System Information Page You can use the System Information page to view information about your router, and to view download, and delete system logs.
The Firmware Upgrade Page You can use the Firmware Upgrade page to get the most recent version of the router firmware, if available. 1 2 Click Browse to open the location where you saved the Firmware Update file that you downloaded from the Zoom web site or received via email. If you are restoring a saved configuration file, select the file that your configuration is saved in. Click Upgrade.
The Reset to Default Dialog You can reset the router to its factory settings by clicking the Reset to Default item from the left pane of the Toolbox menu. The following dialog opens. 1 Click OK to reset the router. We recommend that you back up and save your configuration first if you've made changes and want a record of that configuration The Reboot Dialog You can reboot the router by clicking the Reboot item from the left pane of the Toolbox menu. The following dialog opens.
The Miscellaneous Page You can use this page to Ping a remote device on your network or to wake up a PC on your network that is in sleep mode. The remote PC must be configured for Wake-on-LAN mode.
Appendix A: Mobile Broadband Settings Your router works with a large number of different mobile broadband modem models. In most cases when you plug your mobile broadband modem or phone into the router, the proper APN (Access Point Name), Dialed Number, PIN Code, Username, and Password for the provider is automatically entered. In some cases, the modem does not know this information, and the router needs to be set up to include that information.
Cingular with acceleration ISP.CINGULAR Cingular w/o acceleration ISP.CINGULAR ISP@CINGU LARGPRS.C CINGULAR1 OM Cingular non-contract WAP.CINGULAR WAP@CING ULARGPRS. CINGULAR1 COM ISPDA@ Cricket Communicat ions Edge Wireless CINGULAR1 #777 ISP *99# Mid-Rivers Wireless guest guest #777 Check with provider Check with provider *99# guest guest internet3.voicestre am.com *99# guest guest wap.voicestream.
U.K. Mobile Broadband Service Providers Provider APN Dialed Username Password Other Settings Number three.co.uk *99# 3internet *99# AirTel Vodafone (Jersey) Airtel-ci-gprs.com *99# Anvil Mobile (1) m2m.sim4life.com *99# Anvil Mobile (2) m2m.aql.net *99# asdamobiles.co.uk BT Mobile Business BT Mobile Customer Value 3 3 Mobile Broadband ASDA Jersey Telecom guest guest guest guest *99# wap wap btmobile.bt.com *99***1# bt bt btmobile2.bt.
O2 Mobile Broadband Pay&Go m-bb.o2.co.uk *99# Orange orangeinternet *99# Orange (contract) orangeinternet Orange Pay Monthly 02bb password *99# Orange orange orangeinternet *99# user user Orange Pay and Go orangewap *99# Multimedia Orange Sure (C&W Jersey) Internet *99# T-Mobile (1) general.t-mobile.co.uk *99# User mms T-Mobile general.t-mobile.co.uk *99# user pass prepay.tesco-mobile.com *99# tescowap password Virgin Mobile (1) goto.virginmobile.
Appendix B: How to Set Up Tethering on the iPhone These instructions are based on using the iPhone in the USA with Verizon and AT&T, and may vary slightly depending on the model of your iPhone, your firmware version, and service provider. These instructions assume that you have a service contract that supports tethering. Please consult your iPhone user manual for more information. 1 2 3 Connect one end of the USB cable to the Router and the other end to the iPhone. Turn on tethering on the iPhone.
Appendix B: How to Set Up Tethering on the iPhone 79
Appendix C: Registering Your Product and Getting Help Zoom supports this Router. If you need assistance, please contact Zoom directly. We encourage you to register your product and to notice the many support options available from Zoom. Please go to www.zoomtel.com and select Technical Support. From there you can register your new Modem/Router, contact our technical support experts, use our SmartFactstm intelligent database, and get warranty information.
Limited Warranty Zoom Telephonics, Inc. (hereinafter “Zoom”) warrants this product against defects in material and workmanship for a warranty period of one year. The one year warranty may be extended only by Zoom as required by local law in the country where this modem is sold by Zoom. This warranty applies to the original end-user purchaser.
Declaration of Conformity Déclaration de conformité / Declaración de conformidad Zoom Telephonics, Inc. 207 South Street Boston, MA 02111 USA 617-423-1072 www.zoomtel.com Zoom Wireless-N Router Manufacturer/Constructeur/Fabricante Brand/Marque/Marca Type/Typ/Tipo Series 1100, Model 4504, CDW531AM-002 The manufacturer declares under sole responsibility that this equipment is compliant to Directive 1999/5/EC, 2004/108/EC, 2006/95/EC via the following. This product is CE marked.
FCC Section 15.105 Information to the user Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
