Specifications

PEDAL PITCH Modes and Pitch Shift Ranges
The effect with the above pedal s tatus is the same as
when the Pedal mode is 1.
This effect enables the pitch of the effect sound to be
shifted within a range of four ovtaves.
Parameter 2 Pitch 0 – 24
Parameter 3 Pitch-fine -5 – + 5
Parameter 4 Shift dn, UP
Parameter 5 Balance ★ 0 – 10
Explanation
(2) Pitch
Determines the extent of the pitch shift in units of
semitone.This is used to set the extent of the change you
want to make with the shift within a range of two
octaves. Parameter 4 is used for setting the shift as up or
down.
(3) Pitch-fine
Fine-tunes the extent of the shift determined with
Parameter 2 (PITCH).
(4) Shift
Determines the direction in which the pitch is shifted.
dn: The pitch lowers.
UP: The pitch rises.
(5) Balance
Determines the balance between the effect sound and the
direct sound. When the setting is 0, only the direct sound
is output; when the setting is 10, only the effect sound is
output.
To obtain a chorus effect with little modulation, set
PITCH to 0 and raise PITCH-FINE ever so slightly.
You can create a distinctive, dazzling sound by adding a
short delay (from a few to several tens of milliseconds) to
the direct sound, and then periodically altering the delay
time.
Parameter 2 Depth 0 – 10
Parameter 3 Rate ★ 1 – 50
Parameter 4 F.B-peak 0 – 10
Parameter 5 Manual-mode 0 – 10
Explanation
(2) Depth
Determines the depth of the FLANGER effect.
(3) Rate
Determines the speed of the vibrato for the FLANGER
effect.
(4) F.B-peak (Feedback Peak)
By raising the value of this parameter, the modulation is
emphasized and the sound acquires a powerful
expression.
(5) Manual-mode
Determines the pre-delay time. This changes the tone.
You can create a blistering sound by adding an effect sound
with a staggered phase to the direct sound, and then
periodically altering the phase staggering. If this effect is
used for guitar cutting, the phrase acquires a speedy feel.
Parameter 2 Depth 0 – 10
Parameter 3 Rate ★ 1 – 50
Parameter 4 F.B-peak 0 – 10
Parameter 5 Manual-mode 0 – 10
Explanation
(2) Depth
Determines the depth of the PHASE effect.
(3) Rate
Determines the speed of the vibrato for the PHASE
effect.
(4) F.B-perk (Feedback Peak)
Attaches a tonal texture to adjust the PHASE effect.
(5) Manual-mode
Determines the offset for the PHASE effect.
4: PHASE
3: FLANGER
HINTHINT
2: PITCH SHIFT
HINTHINT
■ 30
EFFECT TYPES AND PARAMETERS
Mode
Pedal up Pedal down
1: Dirty bend
(Dirty BEND)
-100 cent DRY
2: Harmonized choking
(Harm Chokin')
-200 cent+DRY -10 cent+DRY
3: Detune (Detune) Doubling +50 cent+DRY
4: Bend down
(0 2nd)
0 cent -200 cent
5: Bend up
(0 1oct)
0 cent +1 oct
6: Arm down 1
(0 1oct)
0 cent -1 oct
7: Arm down 2
(0 2oct)
0 cent -2 oct
8: Infinity bend down
(0 ∞)
0 cent - ∞
9: Minor/major
( b3rd 3rd)
+300 cent+DRY +400 cent+DRY
10: Octave harmony
( 1oct 1oct)
-1 oct+DRY
+1oct+DRY
11: Perfect 5th/perfect 4th
( 5th 4th)
-700 cent+DRY
+500 cent+DRY
12: 5th/6th
( 5th 6th)
+700 cent+DRY +900 cent+DRY
13: 4-octave shift -2 oct +2 oct
14: Manual flanger
(Hi-BAND)
+1 oct+DRY +2 oct+DRY
15: Cross fade
(X-fade)
- ∞+DRY +1 oct
16: Stop (Scratch) +1 oct+DRY - ∞
→ ↓
→ ↑
→ ↓
→ ↓
→ ↓
→ ↑ ↑
→ ↑ ↓
→ ↑ ↓
↑ → ↑