QUICK START and REFERENCE GUIDE for USB Faxmodems
NOTICE This document contains proprietary information protected by copyright, and this manual and all the accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No part of this document may be photocopied or reproduced by mechanical, electronic, or other means in any form.
Contents INTRODUCTION................................................................................ 4 WHAT YOU NEED TO USE YOUR FAXMODEM..................................... 4 SYSTEM REQUIREMENTS ..................................................................... 5 CHAPTER 1: SETTING UP YOUR USB FAXMODEM ................ 6 INSTALLING THE DRIVERS ................................................................... 6 CONNECTING THE FAXMODEM TO YOUR COMPUTER ..........................
Introduction Welcome to the world of USB faxmodems. A faxmodem equipped with a Universal Serial Bus, or USB, means convenience, ease of installation, and high performance. You can install your USB modem quickly, without bothering with a separate power supply or having to worry about your computer’s internal settings, as you might with other types of external or internal modems. Your USB faxmodem supports both the V.90 ITU Standard and K56flex, the most widely used pre-standard 56K technology.
If you want to use the modem as a telephone answering machine, you’ll also need: • A soundcard, microphone, and speakers or an earphone (PC models) • A microphone and speakers if not provided with your computer (Macintosh models).
Chapter 1: Setting Up Your USB Faxmodem A computer has many devices inside it, or attached to it, such as the mouse or the video card. These devices are controlled by software called drivers. The USB faxmodem also requires drivers. These drivers reside on the Zoom Link CD, and are installable in a few simple steps. Installing the Drivers REMEMBER IMPORTANT You must install the modem drivers before you install the USB faxmodem.
For both the Macintosh and the PC, the installation interface also provides for uninstalling the drivers, if you ever need to. One final note: Don’t install any of the other software on the Zoom Link CD at this time. Connecting the Faxmodem to Your Computer 1 Find the serial number of your faxmodem on the bottom of the case, just under the bar code. Write the number in the Important Information table on the last page of this manual. 2 You do not have to shut down your computer. Connect the cable.
MODEM (ENLARGED TO SHOW DETAIL) COMPUTER TELEPHONE TELEPHONE LINE 5 Turn the faxmodem on by pushing in the power button on the front, shown in the following illustration. Note: Although the faxmodem has an on/off switch, we recommend that you leave it on whenever your computer is on; it draws minimal power.
modem will perform a brief self-test. Then the 6 The READY light should go on to show that the faxmodem is ready for use. Note: If the computer goes into power-save mode (also referred to as “going to sleep”), the modem’s READY light will go off. The light will go on automatically whenever the faxmodem is in use. The USB faxmodem has a set of eight indicator lights on the front. A chart explaining what the lights mean is on the following page.
Summary of the Indicator Lights Light Description OH (Off Hook) ACTIVITY Lights when the faxmodem is off hook. Flashes whenever data or commands are transmitted from the serial port of your computer (or other device) to the faxmodem, or vice-versa. At high speeds the light may appear to be continuously on. Blinks on and off when detecting incoming ring. Lights when the Data Carrier Detect (DCD) signal from the faxmodem to the computer is on. Lights when using V.42 or MNP 4 error correction and V.
If you have a Mac: • Double-check that the USB faxmodem is selected under Settings. Installing the Software Consult the Software Installation Guide that came with your faxmodem to install a complete faxing and communications package that will help you get the most out of your modem. Also explore the other software offerings on the Zoom Link CD. The CD describes each program and offers easy point-and-click installation. That’s it! We hope you enjoy the use of your new USB faxmodem.
Chapter 2: Using the Faxmodem If you have installed the fax and communication software that came with your faxmodem, you probably do not need to read this chapter. The software sets itself up automatically and takes care of sending any necessary commands to the faxmodem. You may, however, want to read this chapter if you want to learn some general facts about how software works with your faxmodem or if you intend to use your new faxmodem with other software.
Tips for Selecting Setup Options In setting up some older software programs, you may be asked to enter certain information. Most programs have default settings that are correct for use with this modem, and there is no need to change them. Nevertheless, you should be aware of the following items: • If you are asked to select the “modem type” from a menu, and you don’t see this modem listed by name on the menu (for instance, Zoom External V.90 56K USB Faxmodem), select the most descriptive name such as V.
Here are two of the more useful AT commands: • If your software suggests an initialization string for this modem, you should use it. If this modem is not listed by your software and no initialization string is suggested, use the following: AT &F. This command returns the modem to the default factory settings. • If your phone service includes Call Waiting, an incoming call can disrupt your modem connection.
nect while the hard drive restarts and activates the software. If this happens, you should deactivate the feature of your power saving option that stops the hard drive. See your computer's documentation for details. Using Video Your faxmodem supports video applications through the V.80 standard protocol so that it can be used for highquality modem-to-modem videoconferencing. The modem is compatible with H.324 point-to-point and H.323 Internet video conferencing standards.
Chapter 3: Solving Common Problems Note: If your modem is not working, please read this chapter and Chapter 2: Using the Faxmodem on page 12 carefully. For installation problems, refer to Chapter 1: Setting Up Your USB Faxmodem on page 6. This chapter covers three categories: general troubleshooting, dial troubleshooting, and on-line troubleshooting. General Troubleshooting Problem: The software cannot find the modem and the modem does not respond to AT commands.
Solution: Your modem has a small speaker on its board that gives you audible feedback of dial tones and remote connection signals (“handshaking”). This is not the same as the speaker that you may have connected to your computer’s soundcard. If the software allows you to control the volume of the on-board speaker, make sure the speaker is enabled and set to a comfortable volume.
Make sure your modem has hung up from the previous call. Select Hang Up in your software or type ATH in terminal mode. On-line Troubleshooting Problem: Your modem disconnects while communicating with a remote system. Solution: The remote system has hung up. You need to reconnect. The telephone line disrupted your call. If your telephone service includes Call Waiting, turn it off by including a special code in the dial prefix (consult your phone company for details).
Problem: Your modem does not make a connection. Solution: If your modem places calls but never makes a connection, make sure you are dialing the right number. The remote modem may be turned off.
Appendix A: Removing a PC’s Internal Modem If your PC does not already have an internal modem installed, or if you are replacing an external modem, you do not need this section. Note: Although you do not have to remove your internal modem, we recommend that you do so. Removing your old modem frees up resources for other internal devices you may want to install in the future.
Appendix B: Regulatory Information FCC Part 15 Emissions Statement This modem has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly. If this device should malfunction, it may also cause harm to the telephone network; should this occur, this device should be disconnected from the network until the source of the problem can be determined and repair has been made. If a device which harms the network is not removed, the telephone company may temporarily disconnect service.
Notes
Important Information In the event you need to call for technical support or customer service, you will need the information below. We recommend that you take a few moments to fill in the following information for your future reference.
