Specifications

You can define the function of the [FUNCTION] switch on the front panel of the 2100. This section explains how to assign
and use the function.
8
Selecting the function of the [FUNCTION] switch
Using the [FUNCTION] switch
One of four functions can be assigned to the [FUNCTION] switch, depending on the application.
Press the [UTILITY] key in Play mode or Edit
mode.
Press the right-most parameter select key.
Use the [VALUE+/–] key to select a function.
The following four functions are available:
● bd (Bank Down)
When you assign this function to the switch,
pressing the [FUNCTION] switch in Play mode
causes the bank with one number lower to be
recalled. (This is the reverse operation of the
[BANK▲] switch.) This function is useful when you
need to switch banks frequently during
performance.
● Mn (Manual)
When you assign this function to the switch, using
the [FUNCTION] switch enables you to toggle
between Play mode and Manual mode. In Manual
mode, you can use foot switches 1–3 and the
[BANK▲] switch to turn the effect module in its
entirety on and off.
In Manual mode, the following modules are
assigned to foot switches 1–3 and the [BANK▲]
switch:
Switch: Corresponding module
Foot switch 1 COMP/WAH
Foot switch 2 DIST
Foot switch 3 MOD
[BANK▲]switchREV/DLY
• You can also turn the module on and off by pressing and
holding the parameter select key. You can use this
method either in Play mode or Edit mode.
• You cannot turn the EQ module on and off using the foot
switches. Use the parameter select key.
● Ct (Control)
When you assign this function to the switch,
operating the [FUNCTION] switch enables you to
control the RTM function that changes a given
effect parameter or volume setting in real-time.
See page 14 for more information on the RTM
function.
● JP (Jam Play)
When you assign this function to the switch,
operating the [FUNCTION] switch enables you to
turn on and off the basic samplers (the Jam Play
function) that can record up to five seconds of
data. See page 9 for more information on the Jam
Play function.
Press the [GROUP/EXIT] key.
The 2100 returns to Play mode. The function
selection for the [FUNCTION] switch will reset to
the previous setting unless you store the patch. If
you wish to store this setting, store the patch.
(See page 11.)
Type(RTM)
Sens
/
Rate
POSITION
POSITION 1.COMP/WAH•DIST
2.DIST•COMP/WAH
COMP
/
WAH
Type
Gain
/
Top
Tone
/
Body
LevelPatch Level
DIST
Treble
Middle
Bass
ZNR
EQ
Type
Depth
/Time
Rate
/Pit/FB
Mix
/Mode
MOD
Type
Time
Tone
/FB
Mix
REV
/
DLY
1.AUX Mix
3.AUX Rch
2.AUX Lch
1.COMP
2.PEDAL-WAH
3.AUTO-WAH
4.TREMOLO
5.RING MOD
6.SLOW ATTACK
4.PLAYNOTE
Max Rec Time
Constant Pitch
Tone
Gain TrimMaster Level
JAM 1 JAM 2 JAM 3 JAM REC
Presence Amp Sim Rev Trim FUNCTION
SAMPLER COMP
/
WAH
UTILITY
PARM
1.CLEAN
2.OVER DRIVE
3. DISTORTION
4.FUZZ
/
GRUNGE
5.LEAD
6.METAL
7.ACOUSTIC
DIST
1.CHORUS
2.STEREO CHO
3. FLANGER
4.PHASE
5.PITCH
6.PEDAL-PITCH
7.DELAY
MOD
1.HALL
2.ROOM
3.PP-DELAY 1
4.PP-DELAY 2
REV/
DLY
JAM PLAY
MONITOR
ON
/
OFF
VALUE
+
–
B
321
GROUP(EXIT)
PATCHBANK
STORE
PRESETBOTH
BANK
SAMPLER
FUNCTION
SPEED
REC
NOTE