Install Instructions

ManualsBrandsZoneFirst ManualsDamper Controls2 or 3 Zone Heat Pump, Dual Fuel & Conventional Control Panel Up to 2H/2C

FORM 2316

The heating limit is adjustable from 110°F to 170°F. The cooling limit

is fixed at 45°F. When the ZPS senses heating above its set point, or

cooling below its set point, the H32 will drop both all stages of

heating or cooling. The ZPS must sense a 10°F fall for heating or rise

for cooling before re-activating the first stages of heating or cooling. If

two stage heating or cooling is being used the second stage timer will

start again once the first stage is re-activated.

The ZPS requires 2 wires from the sensor to the ZPS terminals on the

H32 panel.

Outdoor Air Sensor - OAS

The Outdoor Air Sensor is used only when using a Heat Pump with

Dual/Fossil Fuel back-up furnaces. The OAS senses the outdoor air

temperature and switches the heating control between the heat pump

and the fossil fuel furnace. The temperature set point for this is

adjustable on the Outdoor Balance Point (OBP) dial on the control

panel. It is adjustable from 5°F to 53°F.

Sta

ge Timer

The H32 has a built-in stage timer that eliminates the need and added

cost of using two stage thermostats. On a call for either heating the

timer begins. Setting the Stage Timer dial provides an adjustable time

delay of 5 to 21 minutes between the first and second stage calls.

PURGE TIME

The H32 has a built-in Purge Time after each call is satisfied and

provides a minimum off time before another call is initiated. The

Purge Time is set at 2minutes after all calls for a particular mode are

satisfied or when the Changeover Timer requires a changeover due to

opposing calls.

After all calls are satisfied or the changeover timer activates, the Purge

Timer begins and the heating or cooling, whichever was on, is

deactivated. Typically the fan may be running during this time and the

damper(s) to the last zone(s) calling will remain open to purge the

conditioned air only into those zones that were calling for the

conditioning. DIP Switch 5 can be set ON to keep the Fan running

during the Purge mode in order to prevent the fan cycling off and

back on between modes. In the instance where the Fan staying may

create a draft, and the frequency of opposite calls is minimal this

switch can be kept to OFF.

nimum On Timer

The H32 also has a minimum on time whenever the compressor

operates in order to prevent frequent short cycling. Once there is a

call for cooling or the compressor on a heat pump, the H32 will hold

that call for a period of 2 minutes.

ANGEOVER TIMER

Whenever a call is made for either heating or cooling, the changeover

timer is activated in order to track the amount of time heating or

cooling is on. When an opposite call is made after a first call is made,

the changeover timer calculates the amount of time the unit has

already been supplying the first mode in order to determine how long

it will hold off the opposite call. If an opposite call is made shortly

after the first call, the opposite call may be held off for as much as 20

minutes. If the first call or subsequent calls for the first call mode has

had that mode operating for up to 20 minutes already and an

opposite call comes in after 20 minutes, the changeover timer will

immediately recognize the opposite call, shutting off the current

mode, enter the purge mode and automatically switch to the opposite

mode.

The longer a call has been running up to 20 minutes, the shorter the

wait time will be for an opposite call. If a call is over 20 minutes and

an opposite call is made the changeover will be immediate following

the purge time. This intelligent changeover timing makes the H32

unique to any other zoning system.

CHECKOUT

The H32 has unique features that simplify the checkout of the system

and has LED readouts that constantly indicate the system operation.

Once 24 Volt Power is applied to the panel the Green Power LED will

illuminate. This will stay illuminated constantly when power is applied.

The System LED will provide several different indications based upon

color and if it is flashing.

First Stage Heat Call – RED

Second Stage Heat Call – RED Flash 1/Second

Heat Limit – Red/Amber Alternate Flashing

First Stage Cool Call - GREEN

Second Stage Cool Call – GREEN Flash 1/second

Cool Limit - GREEN/Amber Alternate Flashing

FAN ON - AMBER

PURGE - AMBER Flashing

Each zone has its own small Green indicator LED next to each zone

relay. This light is lit when the specific zoning is calling for the mode

shown on the System LED.

WIR

ING

The H32 is very simple to wire and requires only a minimum number

of connections. The H32 terminal blocks are color coded and screw-

less for all wires to be easily pushed into their respective terminal by

de-pressing the button for each point and releasing once the wire is

seated. (Solid wire can often just be pushed into the terminal without

de-pressing the button.) To remove the wire, just press its button again

and remove the wire.

110

120

130

140

150

160

170

HIGH LIMIT

LAS

OAS

Leaving Air Sensor

In Supply Air Duct

Outdoor Air Sensor only used with

Fossil/Dual Fuel Applications

OBP

STAGE TIMER