Resuscitation System Model 100 AutoPulse® Power System User Guide P/N. 12457-001 Rev.
Power System User Guide Notice About this Guide The information in this User Guide applies to the ZOLL AutoPulse® Power System designed for the AutoPulse Resuscitation System Model 100. The AutoPulse Power System consists of the AutoPulse Multi-Chemistry Battery Charger and the AutoPulse Li-Ion Battery and/or the AutoPulse NiMH Battery. ZOLL shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Power System User Guide Table of Contents 0 Figures ......................................................................................................................v Tables .......................................................................................................................vi Preface ....................................................................................................................vii Who Should Read this Guide .....................................................
Power System User Guide 7.2 Replacing a AutoPulse Multi-Chemistry Battery Charger Fuse ...........................................7-1 Appendix A AutoPulse Daily Checklist ..............................................................A-1 Appendix B Troubleshooting .............................................................................. B-1 Appendix C Technical Specifications ................................................................. C-1 C.1 Li-Ion Battery Physical and Environmental ............
Power System User Guide Figures 0 Figure 1-1 AutoPulse System ................................................................................................. 1-1 Figure 1-2 Recommended component ratios ......................................................................... 1-2 Figure 2-1 The AutoPulse Li-Ion Battery ................................................................................. 2-2 Figure 3-1 AutoPulse System NiMH Battery ............................................................
Power System User Guide Tables 0 Table 4-1 AutoPulse Multi-Chemistry Battery Charger Status LEDs ....................................... 4-4 Table 5-1 AutoPulse Li-Ion Battery Status LEDs ...................................................................... 5-1 Table 5-2 Battery Status LEDs ................................................................................................ 5-3 Table B-1 Battery Troubleshooting Procedures ......................................................................
Power System User Guide Preface 0 This document describes the operating steps and maintenance requirements for the AutoPulse Power System for use as part of the AutoPulse Resuscitation System Model 100. The AutoPulse Power System consists of the AutoPulse Multi-Chemistry Battery Charger and the AutoPulse Li-Ion Battery and/or the AutoPulse NiMH Battery.
Power System User Guide Caution: Do not operate the Multi-Chemistry Battery Charger in a confined space. Caution: Do not position the Multi-Chemistry Battery Charger so that it is difficult to unplug the power cord. Caution: Keep the Multi-Chemistry Battery Charger away from moisture. Caution: Do not remove the Multi-Chemistry Battery Charger cover. The Multi-Chemistry Battery Charger has no internal user-serviceable parts.
Power System User Guide Caution: If Battery pack leaks, do not allow the liquid to come into contact with skin or eyes. If contact has been made, do not rub. Rinse skin or eyes with clean running water and immediately seek medical attention. Caution: Do not heat, burn, or incinerate a Battery. Never expose a Battery to an open flame. Exposure to heat above 158ºF (70ºC) may irreversibly damage the Battery. Incinerating the Battery may result in flames or explosion.
Power System User Guide Date of Manufacture Manufacturer EU Authorized Representative SN Serial Number Recycle Li Ion +113ºF (+45ºC) Temperature Limitations - 4ºF (-20ºC ) Do not discard Rechargeable Battery Do Not Incinerate Fuse DC Voltage AC Voltage Charging Ready Fail Test Cycle Power Page x P/N. 12457-001 Rev.
Power System User Guide 1 Introduction of the AutoPulse Power System The AutoPulse Power System consists of a battery (either the AutoPulse Li-Ion Battery or AutoPulse NIMH Battery) and battery charger (the AutoPulse Multi-Chemistry Battery Charger). Battery: Both the AutoPulse Li-Ion Battery and the AutoPulse NIMH Battery are proprietary, rechargeable, removable batteries that are specifically designed to supply power for AutoPulse operation.
Power System User Guide 1.1 Recommended Battery, Charger and AutoPulse Ratios An AutoPulse unit in general should be equipped with three to four Batteries to allow for two with the device (one for operation and one as a spare) and one to two being charged to support the next shift change, exchange or replacement after a patient use (see Figure 1-2 below).
Power System User Guide 2 AutoPulse Li-Ion Battery The AutoPulse Li-Ion Battery (see Figure 2-1) is a proprietary, rechargeable, removable Lithium-Ion battery that is a power source for the AutoPulse Platform. The AutoPulse Li-Ion Battery is mechanically keyed to the AutoPulse Platform and Multi-Chemistry Battery Charger to facilitate correct installation. One end of the AutoPulse Li-Ion Battery contains connections for power and communications.
Power System User Guide Power and Communications Remove Protective Plastic Cap before use Status Check Button Figure 2-1 The AutoPulse Li-Ion Battery 2.1 Expected AutoPulse Li-Ion Battery Life The expected service life of a properly maintained AutoPulse Li-Ion Battery is three years from its date of manufacture. ZOLL recommends that customers plan to purchase batteries on intervals that reduce the likelihood that they will have all batteries due for replacement simultaneously.
Power System User Guide 3 AutoPulse NiMH Battery The AutoPulse NiMH Battery (see Figure 3-1) is a proprietary, rechargeable, removable Nickel-Metal Hydride battery that is a power source for the AutoPulse Platform. The AutoPulse NiMH Battery is mechanically keyed to the AutoPulse Platform and the AutoPulse Multi-Chemistry Battery Charger to facilitate correct installation. One end of the AutoPulse NiMH Battery contains connections for power and communications.
Power System User Guide Power and Communications Remove Protective Plastic Cap before use Status Check Button Green LED Amber LED Red LED Figure 3-1 AutoPulse System NiMH Battery 3.1 Expected AutoPulse NiMH Battery Life The expected service life of the AutoPulse NiMH Battery is 100 full charge/discharge cycles or 2 to 4 years depending on battery maintenance and usage patterns.
Power System User Guide 4 The AutoPulse Multi-Chemistry Battery Charger The AutoPulse Multi-Chemistry Battery Charger is a stand alone unit intended to charge and automatically maintain both the AutoPulse Li-Ion Battery and the AutoPulse NIMH Battery. The AutoPulse Multi-Chemistry Battery Charger has two charging bays, each with its own indicators. The AutoPulse Multi-Chemistry Battery Charger is designed to charge, maintain, and test batteries for optimum performance in the AutoPulse.
Power System User Guide Caution: Keep the AutoPulse Multi-Chemistry Battery Charger away from moisture. Caution: Use the AutoPulse Multi-Chemistry Battery Charger only with a ZOLL AutoPulse MultiChemistry Battery Charger Power Cord. To prepare the AutoPulse Multi-Chemistry Battery Charger for use: 1. Plug the alternating current (AC) power cord into the power receptacle on the back of the AutoPulse Multi-Chemistry Battery Charger. 2. Plug the AC power cord into an appropriate wall outlet receptacle. 3.
Power System User Guide Note: Do not slam a Battery into a Charger because doing so may cause damage to the Battery’s Connector. Note: Both Batteries are mechanically keyed so that they can only be inserted in one orientation. Do not force a Battery into a charging bay. If resistance is met, check for appropriate orientation, and check to ensure that there are no obstructions to battery insertion. Figure 4-2 Sliding the Battery into a Multi-Chemistry Battery Charger Charging Bay 2.
Power System User Guide 4. AutoPulse Li-Ion batteries placed in a charging bay are automatically charged and tested for minimal performance (Charging LED illuminated) in less than 4¼ hours. 5. AutoPulse NiMH batteries placed in a charging bay are automatically charged and tested for minimal performance (Charging LED illuminated) in less than 6¼ hours. Note: Do not remove a Battery from the Multi-Chemistry Battery Charger until its charging completes, or the Battery’s run time will be reduced. 6.
Power System User Guide Table 4-1 AutoPulse Multi-Chemistry Battery Charger Status LEDs (Page 2 of 2) MultiMulti-Chemistry Chemistry Battery Charger Battery Status LEDs Used Charger Mode Definition Action Idle The Battery Charger is unable to Remove and re-insert the Battery. If recognize the Battery. the status is still Idle, refer to Appendix B, “Troubleshooting” for more information. Note: Newly-charged Batteries can be warm to the touch. This is a consequence of normal operation. 4.2.
Power System User Guide [This page left intentionally blank.] Page 4-6 P/N. 12457-001 Rev.
Power System User Guide 5 Using the AutoPulse Battery 5.1 AutoPulse Li-Ion Battery Status Check To determine if an AutoPulse Li-Ion Battery needs to be charged, press the Status Check button on the AutoPulse Li-Ion Battery (see Figure 5-1). Status Check Button Figure 5-1 AutoPulse Li-Ion Battery Status Check Button and Status LEDs The AutoPulse Li-Ion Battery status light-emitting diodes (LEDs) will illuminate (refer to Table 5-1).
Power System User Guide Table 5-1 AutoPulse Li-Ion Battery Status LEDs (Page 2 of 2) Status LEDs Definition None The AutoPulse Li-Ion Battery voltage is Charge the AutoPulse Li-Ion Battery by placing it too low to illuminate the LEDs. into the AutoPulse Multi-Chemistry Battery Charger. 5.2 Action AutoPulse Li-Ion Battery Installation The AutoPulse Li-Ion Battery is mechanically keyed so that it can only be inserted in one orientation.
Power System User Guide To remove the Battery, first rotate the Battery Latch into the open position as shown in Figure 5-2. Then hold the AutoPulse Platform firmly and grip the Battery while pulling the finger latch outwards to disengage the locking bar (see Figure 5-2), then pull the Battery straight out until it fully clears the battery compartment. Caution: Only use ZOLL Batteries specifically designed for use with the AutoPulse.
Power System User Guide 5.4 AutoPulse NiMH Battery Installation To install the AutoPulse NiMH Battery, first make sure the Battery Latch is rotated out of the way so that the AutoPulse NiMH Battery can slide into the Battery compartment Then slide the AutoPulse NiMH Battery into the Battery compartment in the AutoPulse Platform. The Battery should snap into place and mount flush with the AutoPulse Platform. Then rotate the Battery Latch into position.
Power System User Guide Caution: Only use ZOLL Batteries specifically designed for use with the AutoPulse. The use of other batteries may cause permanent damage to the AutoPulse and will void the warranty. P/N. 12457-001 Rev.
Power System User Guide 5.5 Battery Rotation After every use, at the beginning of a shift, or at least once every 24 hours, the Battery in the AutoPulse should be replaced with a fully charged Battery. Recommended daily 4 Battery maintenance routine 1 Replace the spare Battery with a freshly-charged Battery from the Charger. 2 Check the Battery status LEDs before placing a Battery in service. 3 Replace the Platform Battery with a freshly charged Battery from the Charger.
Power System User Guide Recommended daily 3 Battery maintenance routine 3 Place the Battery that was in the AutoPulse into the Charger. Check the Battery status LEDs before placing a Battery in service. 1 Remove fully charged Battery from the Charger and store it with the AutoPulse as the spare. 2 Install the previous spare Battery into the AutoPulse. Figure 5-6 Three Battery rotation Three Battery Rotation—to be done after every use and/or once per shift (see Figure 5-6 above).
Power System User Guide [This page left intentionally blank.] Page 5-8 P/N. 12457-001 Rev.
Power System User Guide 6 Managing the AutoPulse Power System 6.1 AutoPulse Battery Management The AutoPulse System is intended to be deployed in a state of high-readiness. Therefore, daily AutoPulse System checks should be integrated into Emergency Medical Service (EMS) rig-check or hospital procedures. AutoPulse Batteries that are not fully charged (Battery Status LED is yellow/amber or there are less than four bars on the AutoPulse User Control Panel), will result in shorter AutoPulse run times.
Power System User Guide Wipe the Battery completely dry with a clean dry cloth. Ensure the Battery is completely dry prior to placement in the AutoPulse Platform or the Multi-Chemistry Battery Charger. Inspect the Battery per Section 6.2.2. 6.2.2 AutoPulse Battery Inspection The Battery should be physically and visually inspected on a regular basis to ensure it is in a state of operational readiness. Caution: Do not use a Battery that has cracks in the Battery case exposing internal components.
Power System User Guide AutoPulse Batteries stored outside the Multi-Chemistry Charger for longer than 4 weeks may be subject to irreparable damage. Warning: Always charge a stored Battery before placing the Battery in active operation. Battery may self-discharge when not in use. Failure to charge a Battery before use may cause device power failure. In no case should any Battery be used if it has not been charged within 2 days. 6.2.
Power System User Guide [This page left intentionally blank.] Page 6-4 P/N. 12457-001 Rev.
Power System User Guide 7 AutoPulse Multi-Chemistry Battery Charger Maintenance Warning: No modification of the AutoPulse Multi-Chemistry Battery Charger, the AutoPulse Li-Ion Battery, or the AutoPulse NiMH Battery is allowed. Caution: Do not remove the AutoPulse Multi-Chemistry Battery Charger cover. The AutoPulse MultiChemistry Battery Charger has no internal user serviceable parts. 7.
Power System User Guide 3. Check both of the fuses. If a fuse must be replaced, follow these steps: a) Replace both of the original fuses with T2.5A 250V AC fuses. b) Push in the fuse holder until the locking tab clicks into place. c) Re-attach the Power Cord. d) When the AutoPulse Multi-Chemistry Battery Charger is powered on, all the LED’s illuminate briefly as the Charger performs a self test.
Power System User Guide Appendix A AutoPulse Daily Checklist Battery Serial Numbers Date AutoPulse Spare AutoPulse Self Test Performed Perform AutoPulse Self Test - Install a LifeBand and power on the AutoPulse. On Power up, all LEDs on the display will momentarily light up, then only the Green POWER LED will remain lit.
Power System User Guide [This page left intentionally blank.] Page A-2 P/N. 12457-001 Rev.
Power System User Guide Appendix B Troubleshooting This Appendix details symptoms, possible causes, and recommended actions for difficulties you might have with your AutoPulse Power System. Table B-1 provides troubleshooting procedures for the Battery. Table B-2 provides troubleshooting procedures for the Multi-Chemistry Battery Charger. Table B-1 Battery Troubleshooting Procedures Symptom Possible Cause Recommended Action Battery Status Check LEDs do not illuminate. The Battery’s status is unknown.
Power System User Guide Table B-2 Multi-Chemistry Battery Charger Troubleshooting Procedures (Page 1 of 2) Symptom Possible Cause Recommended Action Multi-Chemistry Battery Charger’s green Power LED is not illuminated. Multi-Chemistry Battery Refer to Chapter 4, “The AutoPulse Multi-Chemistry Charger’s alternating Battery Charger” for more information. current (AC) power cord is not plugged in. Multi-Chemistry Battery Charger’s green Power LED is not illuminated. Blown fuse.
Power System User Guide Table B-2 Multi-Chemistry Battery Charger Troubleshooting Procedures (Page 2 of 2) Symptom Possible Cause One or both of the Battery The Multi-Chemistry Bay’s indicator lights are Battery Charger has all illuminated. detected an internal error in one or both of the Battery Bays. P/N. 12457-001 Rev. 2 Recommended Action Remove the Battery from the Charger. Disconnect the power cord from the wall outlet and then plug the Charger back in.
Power System User Guide [This page left intentionally blank.] Page B-4 P/N. 12457-001 Rev.
Power System User Guide Appendix C Technical Specifications The specifications provided in this appendix apply to the AutoPulse Power System. C.1 Li-Ion Battery Physical and Environmental Table C-1 Li-Ion Battery Specifications (Page 1 of 2) Category Specifications Manufacturer ZOLL Circulation Model Number 8700-0752-01 Size (LWH) 11.5 in. by 3.2 in. by 2.2 in. (29.2 cm by 8.1 cm by 5.7 cm). Weight 3.0 lbs. (1.3 kg). Type Rechargeable Lithium-Ion (LiFePO4) Battery voltage (nominal) 36.
Power System User Guide Table C-1 Li-Ion Battery Specifications (Page 2 of 2) Category Specifications Radiated emissions Meets CISPR 11/EN55011, Group 1, Class A FCC part 15, Class A Radiated Immunity Meets IEC-61000-4-3, 80-2500 MHz, Level 3 Safety Meets IEC-60601-1 including UL310DV.1.1 for Lithium batteries C.
Power System User Guide Table C-2 NiMH Battery Specifications (Page 2 of 2) Category Specifications Free fall Meets IEC 60068-2-31 Basic Environmental Testing Procedures – Free Fall – Procedure 1. Electrostatic discharge Meets IEC 61000-4-2, Level 3 Radiated emissions Meets CISPR 11/EN55011, Group 1, Class A FCC part 15, Class A C.
Power System User Guide Table C-3 Multi-Chemistry Battery Charger Specifications (Page 2 of 2) Category Specifications RF electromagnetic fields immunity Meets IEC 61000-4-3, Level 2 EFT/burst Meets IEC 61000-4-4, Level 2 Surge immunity Meets IEC 61000-4-5, Level 2 Conducted RF disturbances immunity Meets IEC 61000-4-6, Class A Dips, interruptions, and variations Meets IEC 61000-4-11 Harmonics current emissions Meets IEC 61000-3-2, Class A Radiated emissions Meets CISPR 11/EN55011, Group 1,
Power System User Guide C.5 Limited Warranty for AutoPulse Resuscitation System ZOLL Circulation warrants to the initial Purchaser only that the “Warranted Product” purchased hereunder will be free from defects in workmanship or materials, when given normal, proper, and intended usage, for a specified period (“Warranty Period”) from the date of its initial shipment to Purchaser.
Power System User Guide THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY FOR ZOLL CIRCULATION’S PRODUCTS, EXTENDS ONLY TO THE PURCHASER AND IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION ANY WARRANTY AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Power System User Guide Index X A AutoPulse Multi-Chemistry Battery Charger cleaning 7-1 operating 4-2 replacing fuse 7-1 setting up 4-1 troubleshooting A-1, B-1 AutoPulse Power System technical specifications C-1 troubleshooting B-1 AutoPulse System warranty C-5 B Battery capacity C-1, C-2 charge time C-1, C-2 disposal 6-3 specifications C-1, C-2 status check 5-1, 5-3 status lights 5-1, 5-3 storage 6-2 test-cycle time C-1, C-2 Battery orientation diagram 4-3 C charging bay status LEDs 4-4 F FCC statemen
Power System User Guide [This page left intentionally blank.] Page I-2 P/N. 12457-001 Rev.
