R Instruction Manual Stainless Steel Food Jar SWATHE Name of Each Part Lid Cover Stopper Cover Stopper Wave Packing Stopper Gasket g@ ;;i Mouth Ring Mouth Ring Gasket Mouth Food Jar Set ] Container @ Bs sirs that all parts are attached filmy before each use. Please read these instructions before use, and keep for future reference.
Important Safeguards ® Please follow these instructions to prevent scalding, deterioration and discoloration of foods and beverages, as well as malfunction and staining of the product. Do not allow infants or small children to use this product. Keep out of the reach of infants and small children. Mishandling ray cause injury or scalding. This product is for keeping foods and beverages hot or cold. Do not use it for any other purposes.
Important Safeguards @ Please follow these instructions to prevent scalding, deterioration and discoloration of foods and beverages, as well as malfunction and staining of the product. Always use with the Lid Cover, Stopper | Do not remove the sticker Cover, Stopper, Valve Packing, Slipper | from the bottom of the Gasket, Mouth Ring and Mouth Ring Container. Gasket attached. Doing 50 may cause rust, holes Contents may leak and/or cause scalding. or other damage.
Warnings & Cautions Avoid dropping or hitting against hard surfaces. Damage to the plastic or stainless steel surface of the product may reduces its ability 1o retain heat. Do not strongly rub the design on the outside of the Container. It may come off. After washing the Lid Set, remove all water from the parts by shaking them repeatedly and wiping them before reassembly. T Droplets of water remaining on the Lid Cover or Lid Sat may leak out. {Ses p. & for disassembly instructions.
® Before using, wash the Lid Set, Mouth Ring Set and Instructions for Use " oo of the Container thoroughly with lukewarm water. Remove the Lid Set from the Container Turn the Stopper Cover in the = direction of the arrow to remove it. Remove » if you turn the Lid Cover at the same time, it may it off at the same time. Stopper Container Preheat (Precook) @ For better heat/cold retention, the Container by pouring a small amount of hot watercolor water into it and letting it stand for 1-2 minutes.
Disassembling the Lid Set ™ Remove the Lid Sst from the Container Remove the Valve Packing When removing the Valve Pauling, be careful not to damage # with your nails, gz@ As shown in the illustration, grip the bottom part of the Stopper firmly and turn the Lid Cover to remove it Even if it is attached to the Container, the Lid Cover can be removed. Lid Cover The Valve Packing is fitted into the ceder of the Stopper. Remove it using your finger and thumb as shown in the illustration.
Assembling the Lid Set # Be sure to attach the Lid Cover, Stopper Cover, Stopper, Valve Packing, Stopper Gasket, B Mouth Ring and Mouth Ring Gasket correctly. {Otherwise the product may malfunction and the contents may leak.) Attach the Stopper Gasket Line up the recess in the Stopper Casket with the ridge on the Stopper and apply pressure from the outside in to push it into place. not attach the Slipper Gasket inside down.
With the ridge in the Mouth Ring Gasket Twist the Mouth Ring Set facing out, press the Gasket securely into | slightly while pushing it firmly the groove in the Mouth Ring. : onto the Container. o » Mouth Ring After attaching the Gasket, press it in with your fingers. Mot Ring | @ Alter ail aching the Gasket, adjust |t with your fingers 10 ensure that | s nol twisted or bulging.
Care of r Product (continued) During use of this product, hardness or impurities in water may cause rust spots or water scale. To remove theses, fill the Container with hot water mixed with approximately 10% vinegar and let stand with the Lid L Set off for 30 minutes to an hour, then wash the interior thoroughly. {See “Care of Your Product”, p.
