Instruction Manual

9 10 11 12
66
55
44
22
33
44
55
① Pass the Straw Stopper through the Tube.
②Attach the Tube Tip so the end face touches the Tube.
Attach the Straw Stopper.
Insert the Straw Set into the Stopper.
① Insert the Straw Stopper into
the Tube and move it up to the
Straw Set.
② While pushing in the end of the
Straw, turn the Straw Stopper
as illustrated to attach it.
● Make sure not to turn the Straw
Stopper too forcefully. (Doing so
may cause it to deform.)
●
Attach the Straw Stopper as illustrated.
Attach the Straw Stopper
as illustrated.
●Be sure to attach the Stopper Cover Set, Stopper, Stopper Gasket, Straw Set, Straw Stopper, Tube, and Tube Tip correctly to prevent malfunction or leaking of beverages.
Line up the recess in the Stopper Gasket with the ridge on the Stopper,
and, applying pressure from the outside in, push it into place.
11
Attach the Stopper Gasket.
Take the Tube out of the Straw Set.
Remove the Stopper Gasket.
③Turn the Straw Stopper as illustrated to attach it.
Attach the Tube to the Straw Set.
Attach the Tube Tip.
①Insert the Straw Set into the Stopper from above.
How to Assemble the Stopper Set
●See p. 8-9 for how to disassemble.
How to Disassemble the Stopper Set
Pull the Straw Set as illustrated to remove.
Attach the Tube so the end face touches the Straw Set.
(See Note on p. 13.)
Straw Set
Stopper Gasket
Ridge
Push along the rim
with your finger.
Be careful with the top and the bottom of
the gasket and be sure to set correctly.
Not doing so may cause beverages to leak.
Recess
Stopper Gasket
Tube
mark
mark
Tube
Straw Set
Tube
Straw Stopper
Straw Set Side
Straw Stopper
Tube
Tube Tip
Do not remove
this gasket.
Do not remove the spring and
be careful not to lose it.
Straw Set
Tube
Straw
Straw
Straw Set
Up to here
Tube
Up to here
Make sure that the spring is attached.
Straw
Stopper
Flat Side Up
Cross Section
13 14 15 16
66
Attach the Stopper.
Align the opening of the Stopper Cover Set and the tab of the
Stopper, and push the Stopper up to attach securely.
Inside
Main Body
① Wash with a sponge brush or similar dipped in warm
water and mild kitchen detergent.
② Then rinse and wipe moisture out to dry.
● Keeping the inside clean will help prevent odors.
SPECIFICATIONS:
● Clean the product after each use to prevent odors and mold, and to keep
the product sanitary.
● Always disassemble the product before cleaning.
(See “How to Disassemble the Stopper Set” on p. 8-9.)
Outside
Main Body
Stopper Set
① Wash with warm water and mild dishwashing liquid
using a soft sponge.
② Rinse, shake a few times and wipe dry.
● Take apart the Stopper Set before washing and
drying.
● Use a small brush sold in stores if necessary.
How to Take Care of Your Bottle:
You may find rust spots or water stains caused by impurities in the
water. To remove these stains, fill the bottle with hot water with 10%
vinegar and let it stand for 30 minutes to an hour without attaching
the Stopper Set, then wash the interior thoroughly. (See “How to
Take Care of Your Bottle” on p. 14, 15.)
To Remove Coffee and Tea Stains:
To Remove Rust Spots and Water Stains:
Note
When attaching the Straw and the Tube Tip to the Tube, attach them
firmly so that the end face of the Tube touches them.
Examples of Incorrect
Attachment
Straw Set Side
Tube Tip Side
Materials: Inner Liner Stainless Steel (Nonstick Coated)
Exterior Stainless Steel (Acrylic Resin Painted)
Mouth Polypropylene
Stopper Polypropylene
Straw Polypropylene
Lid Polypropylene
Tube Tip Polypropylene
Straw Stopper Polypropylene
Tube Sillicone
Gasket Sillicone
Manufacturer: Zojirushi Corporation
Address: 1-20-5 Tenma, Kita-ku, Osaka 530-8511, Japan
STAINLESS STEEL VACUUM COOL BOTTLE
Model No. Capacity
Cold Retention
(Below)
6 hrs.
SD-CS50
0.52 liter
(18 oz.)
0.27 kg
(10 oz.)
9°C(48°F)
@ 6 hrs.
Weight
Cold Retention Testing Conditions:
At a room temperature of 20°C±2°C (68°F±4°F), the Main Body is filled with
cold water up to the level illustrated in on p. 3, and left
standing in an upright position.
For cold retention, once the cold water reaches 4°C±1°C (39°F±2°F), the
temperature is measured after 6 hours.
Notes for Handling the Product
● Do not use a dishwasher or dish-dryer. Do not boil to sanitize.
● Do not clean using paint thinner, metal wire scrub brushes, scrubbing
brushes that include abrasive cleaners, polishing powders, cleansers,
melamine sponges, or any similar items.
● Do not use chlorine-based bleach. In addition, do not use any kind
of bleach, even non-chlorine-based, to clean the outside of the Main
Body. It may damage the paint, print, or stickers on the Main Body.
● The product is washable, but do not soak it in water for an extended
period of time.
● Wipe moisture off thoroughly to prevent water stains or rusting.
● If the product is not going to be used for an extended period, wash
thoroughly with cold or lukewarm water and dry well. Store the
product away from high temperatures and humidity.
High temperatures and humidity may damage the product.
To remove coffee and tea stains from the interior and the Stopper
Set, we recommend using Zojirushi’s cleaning detergent SB-ZA01E.
(Sold separately.)
Always remove the Stopper Set when using SB-ZA01E."
We take care in only using materials that are safe and hygienic
for food contact. However, if plastic parts become damaged or
its surface becomes rough, please replace them for optimum
performance. The Straw Set, Straw Stopper, Tube, Tube Tip,
Stopper and Stopper Gasket may need to be replaced due to
time and wear. Please check them about once a year. When
replacing parts, please record the model number and part
name beforehand. Then contact either the store where you
purchased the product or Zojirushi Customer Service.
Replacement parts may be available for an additional charge.
Beverage Level
Straw Set
Tube
Tube Tip
Stopper Cover Set
Stopper
Opening
Tab
continued
② Align the ▲ part of the Stopper and the mark of the
Straw, and press the Straw in all the way.
Attaching the Tube