Spec Sheet

ManualsBrandsZoeller ManualsSewage1/2 HP High Head Waste-Mate Cast Iron Sewage Pump (2") w/ Vertical Float

290 Series

Features

The High Head Waste-Mate series of submersible pumps is designed for use in

residential or light commercial dewatering and wastewater applications and can

be used to transfer groundwater and effluent or raw sewage. The innovative

vortex impeller design reduces the risk of clogging and allows each pump to

pass 2" (50 mm) spherical solids. These durable cast iron pumps include a

powder coated epoxy finish to prevent corrosion and are designed to provide

great heat dissipation from the motor, ensuring a long service life. As with every

Zoeller

pump, each one is 100% pressure-tested, submerged and run to

ensure quality and reliability for years of trouble-free performance!

Automatic pumps include a float-operated, 2-pole mechanical switch, a

stainless steel float guard and switch arm, and a solid, buoyant polystyrene

float.

For nonautomatic pumps, variable level control systems and containers of

various sizes are available for longer cycles.

Double seal models are available to improve bearing lubrication and prevent

leaks and damage to seals or bearings during dry run conditions.

All models are hermetically sealed to be watertight, dust-tight, and completely

submersible.

Reserve Powered Design: For unusual conditions, a reserve safety factor is

engineered into the design of every pump.

Specifications

Motor Characteristics

Motor 1/2 - 2 HP

Voltage 115 - 575 V

Phase 1 or 3 Ph

Hertz 60 Hz

RPM 3450 RPM

Type Permanent split capacitor or 3 phase

Insulation Class B

Amps 2.4 - 20.5 Amps

Pump Characteristics

Operation Automatic or nonautomatic

Auto On/ Off Points 15-3/4" / 5" (40.0 cm / 12.7 cm)

Discharge Size 2" or 3" NPT

Solids Handling 2" (50 mm) spherical solids

Cord Length 20' (6 m) standard

Cord Type UL listed, 3-wire neoprene cord and plug

Max Head 75' (22.9 m)

Max Flow Rate 214 GPM (810 LPM)

Max Operating Temp 130 °F (54 °C)

Cooling Oil filled

Motor Protection Auto reset thermal overload (1 Ph)

Materials Characteristics

Cap Cast iron

Motor Housing Cast iron

Pump Housing Cast iron

Base Cast iron

Upper Bearing Ball bearing

Lower Bearing Ball bearing

Mechanical Seals Carbon and ceramic

Impeller Type Non-clogging vortex

Impeller Cast iron, optional bronze

Hardware Stainless steel

Motor Shaft 1117 carbon steel or 416 stainless steel*

Gasket Neoprene square ring and gasket

FM0450_Ea

Updated 0616

Summary of content (3 pages)

PAGE 1
290 Series Specifications Motor Characteristics Motor 1/2 - 2 HP Voltage 115 - 575 V Phase 1 or 3 Ph Hertz 60 Hz RPM 3450 RPM Type Permanent split capacitor or 3 phase Insulation Class B Amps 2.4 - 20.5 Amps Pump Characteristics Operation Automatic or nonautomatic Auto On/ Off Points 15-3/4" / 5" (40.0 cm / 12.
PAGE 2
90 Series Model Model Number Seal Mode Volts Phase Amps HP Hz Lbs M292 Single Auto 115 1 15.0 1/2 60 86 Kg 39 N292/N4292 Single / Dbl Non 115 1 15.0 1/2 60 85/93 38/42 BN292 Single Auto 115 1 15.0 1/2 60 87 39 D292 Single Auto 230 1 7.5 1/2 60 88 39 E292/E4292 Single/Dbl Non 230 1 7.5 1/2 60 88/95 39/43 F292/F4292 Single/Double Non 230 3 5.2 1/2 60 88/95 39/43 J292/J4292 Single/Double Non 200 3 6.
PAGE 3
290 Series Model Number Seal Mode Volts Phase Amps HP Hz Lbs Kg F295/F4295 Single / Dbl Non 230 3 12.2 2 60 91/99 41/44 J295/J4295 Single / Dbl Non 200 3 14.3 2 60 91/99 41/44 G295/G4295 Single / Dbl Non 460 3 6.1 2 60 91/99 41/44 BA295/BA4295 Single Non 575 3 4.9 2 60 91 41 *Single seal models are built with a carbon steel motor shaft, and double seal models are built with a stainless steel motor shaft.