Specification Sheet

ManualsBrandsZoeller ManualsGrinder PumpsZoeller The Shark 2HP Automatic Single Directional Grinder Pump

SECTION: 2.25.050

FM2798

0117

Supersedes

1216

SK1621

PRODUCT SPECIFICATIONS

MOTOR

Horse Power 1.0 - 2.0

Voltage 115*/200/230

Phase 1 Ph

Hertz 60 Hz

RPM 3450

Type Capacitor start / capacitor run

Insulation Class B

Amps 7.7 - 15.5

PUMP

Operation Automatic or nonautomatic

Auto On / Off Variable level ﬂoat switch, customer sets

Discharge Size 1-1/4" NPT vertical discharge

Cord Length 20' (6 m) standard

Cord Type SOW or SOOW multi-wire neoprene

Max. Head 107' (32.6 m)

Max. Flow Rate 46 GPM (174 LPM)

Max. Operating Temp. 130°F (54°C)

Cooling Oil ﬁlled

Motor Protection Auto reset thermal overload

MATERIALS

Cap Cast iron

Motor Housing Cast iron

Adapter Cast iron

Pump Housing Cast iron

Upper Bearing Ball bearing

Lower Bearing Ball bearing

Mechanical Seals Carbon/ceramic

Impeller Type Vortex

Impeller Engineered plastic

Hardware Stainless steel

Motor Shaft Stainless steel

Gasket & Square Ring Neoprene

Cutter Type 440C stainless steel hardened to a

Rockwell C55-60

1 1/4" N.P.T.

18 5/8" [473 mm]

5" [127 mm]

6 1/2"

[165 mm]

4" [102 mm]

7 5/8"

[194 mm]

[102 mm]

Tested to Standard UL778 and

Certied to CSA

Standard C22.2 No. 108

Product information presented

here reects conditions at time

of publication. Consult factory

regarding discrepancies or

inconsistencies.

Your Peace of Mind is Our Top Priority

502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | www.zoeller.com

TECHNICAL DATA SHEET

SHARK GRINDER

Model 818/819/820 Single Seal Grinder Pumps

NOTE: See model comparison chart for specific details.

*115 Volt is for model 818 only

Summary of content (4 pages)

PAGE 1
SECTION: 2.25.050 FM2798 0117 Supersedes 1216 Your Peace of Mind is Our Top Priority ® ® Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies. TECHNICAL DATA SHEET SHARK GRINDER Model 818/819/820 Single Seal Grinder Pumps MATERIALS PUMP MOTOR PRODUCT SPECIFICATIONS Horse Power 1.0 - 2.
PAGE 2
TOTAL DYNAMIC HEAD/FLOW PUMP PERFORMANCE CURVE MODELS 818/819/820 METERS FEET TOTALPER DYNAMIC MINUTE HEAD FLOWAND PERDEWATERING MINUTE SEWAGE 818 819 820 Gal. Liters 43 163 42 159 40 151 37 140 33 125 28 106 22 83 16.5 62 53 ft. (16.2m) Gal. Liters 43 163 43 163 43 163 43 163 43 163 42 159 41 155 39 148 32 121 22 83 12 45 81 ft. (24.7m) Gal. Liters 46 174 46 174 46 174 46 174 46 174 46 174 46 174 46 174 46 174 43 163 36 136 27 102 16.7 63 7 26 107 ft. (32.
PAGE 3
PUMP SYSTEM COMPONENTS (A) GRINDER PUMP STANDARD FEATURES: (E) INDOOR BASIN, COVER, AND HARDWARE PREPACKAGED STANDARD EQUIPMENT • Tri-slice® two-bladed, high-torque cutter • Scissorized cutting action shreds solids down to 7/32" and smaller • 1-1/4" NPT vertical discharge • Carbon/ceramic seal • Thermal overload protection • Engineered, glass-filled plastic impeller with stainless steel insert • Stainless steel cutter plate/cutter • Stainless steel motor shaft • Stainless steel hardware • 2
PAGE 4
(F) OUTDOOR BASIN, COVER, AND Z-RAIL® SYSTEM ASSEMBLIES STANDARD EQUIPMENT • Fiberglass basin with anti-flotation ring • 2" Schedule 80 PVC discharge piping • 1-1/4" x 2" Z-rail® P/N 39-0134 disconnect system, epoxy coated ductile iron • 3/4" Galvanized rail pipes • Stainless steel lifting cable and bail • 2" PVC ball valve • 2" cast iron check valve • PVC float tree • 1-4" rubber inlet pipe seal (field inst.) • 1-2" pipe seal (field inst.