Product Overview

COMPARE THESE FEATURES
RESERVE POWERED DESIGN
For unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.
© Copyright 2014 Zoeller Co. All rights reserved.
DRAIN REPLACEMENT
PUMP PUMP PART
MODEL NUMBER
104 72-0001
105 007917
110 007918
115 007919
120 007920
131 007921
132 72-0001
2010
0
GALLONS
LITERS
0
5
504030
80
160
FLOW PER MINUTE
105/110/
8060 70
240
131
PUMP PERFORMANCE CURVE
104/105/110/115/120/131/132
4
TOTAL DYNAMIC HEAD
2
10
15
6
20
FEET
METERS
25
115/120
104/132
Meters
20 6.1
Shut-off Head:
15 4.6
10 3.0
5 1.5
Feet
MODELS
Liters
273
231
170
19.25 ft. (5.9m)
--
19
34
43
--
72
9525
23 ft. (7.0m)
45
129
163
61
72
Gal.
104/132
Liters Gal. Liters Gal.
131
105/110
115/120
18 ft. (5.5m)
38
14
30
144
53
114
-- --
009898
PUMP FEATURES
(Models 53-55-57-59-98)
• Passes laundry lint
• Automatic, oat operated
mechanical switch
• 115 V/1 PH, all drain pump series
• 9 ft. UL listed 3-wire cord and plug
(15 ft. cord std. on model 98)
• Stainless steel screws, guard, handle and
switch arm
• Passes ½" spherical solids
• 1½" NPT discharge
• 1550 RPM, 60 Hz
1725 RPM on model 98
• Non-clogging vortex impeller
• Glass-lled polypropylene base with built
in strainer on M53 and M55. Model 59, all
bronze construction; model 57 & 98 all cast
iron construction.
• Temperature rated 130°F
• UL and cCSAus listed pump
CHECK VALVE 30-0181
(excluding Model 104 & Model 132)
• “Full Flow” design
• 1½" or 1¼" slip x slip union
• PVC construction
CHECK VALVE 019768 (Model 132)
• “Full Flow” design
• 1½" slip union
• PVC construction
For additional specications see FM0217.
BASIN
• Polypropylene construction
• Corrosion-resistant
• High capacity
• Gasket sealed polypropylene lid
• 2" NPT vent
• 1½" NPT discharge
• 1½" compression slip t for top and side
intake. NOTE: 132 comes preassembled
for side inlet only.
• Threaded connections for
easy installation
• May be installed with internal trap for
space savings
• Gas tight cover
• Temperature rated 130°F
• Fits under most sinks
• Basin passes 10' stack test*
* Models 104 and 132 will not pass 10' Stack Test
(Model 72)
• Passes laundry lint
• 115 V/1 PH, all drain pump series
• 9 ft. UL Listed 3-wire cord and plug
• Stainless steel screws, switch arm and
lower motor housing
• Oil free
• Passes 3/8" spherical solids
• 1½" NPT discharge
• 3400 RPM
• Non-clogging vortex impeller
• Temperature rated 110°F
• cCSAus listed pump
14 1/2 DIA.
12 1/2
11 7/8
9
CORD SEAL
HOLE
1 1/2" DRAIN
INLET (TOP)
1 1/2" NPT
DISCHARGE
2" NPT
VENT
(8) COVER
HOLES
11 3/4 DIA.
1 1/2" DRAIN
INLET (SIDE)
SK2012
EASY INSTALLATION - NO NEED TO DIG A SUMP.
TO REDUCE THE RISK OF ELECTRICAL SHOCK A PROPERLY GROUNDED
RECEPTACLE OF GROUNDING TYPE SHALL BE INSTALLED AND PROTECTED BY A GROUND FAULT
CIRCUIT INTERRUPTER (GFCI) IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND LOCAL
CODES. DO NOT REMOVE GROUND PIN FROM PLUG.
NOTE: For additional inlet option or
high head applications contact factory.