Specification Sheet

ManualsBrandsZoeller ManualsAll ZoellerZoeller Electrical Alternator Control Panel for Duplex Pump Installations

DUPLEX ELECTRICAL ALTERNATING SYSTEM

All electrical systems must be installed by a qualied licensed electrician and according to the National Electrical

Code. (See section 430-71 through 430-113 plus any others that apply)

Refer to FM0712 for correct selection of Electrical Alternator.

SK289

PUMP POWER SUPPLY

NOTE: ALARM - CONTROL

CIRCUIT SHOULD BE

SEPARATE FROM

PUMP POWER

2" OR 3" DISCHARGE PIPE

FLOOR FLANGE

ZOELLER FIBERGLASS

OR POLYETHYLENE

BASIN

ZOELLER FLOAT SWITCH

ZOELLER SEWAGE PUMP

ELECTRICAL ALTERNATOR

CONTROL PANEL

INDICATOR LAMPS (INSIDE ENCLOSURE)

TOGGLE SWITCHES (INSIDE ENCLOSURE)

ZOELLER UNICHCEK

CHECK VALVE (2" OR 3")

4 FLOAT SYSTEM

ALARM BELL "ON"

BOTH PUMPS ALREADY

ACTIVATED SET ABOVE OVERRIDE

4" HUB INLET

"ALARM-OVERRIDE LEVEL SET

ABOVE "ON" FLOAT AND

BELOW INLET BOTH PUMPS

"ON" ALARM BELL "ON"

3 FLOAT SYSTEM

"ON" LEVEL PUMPS ALTERNATE

OPERATION EACH CYCLE MAXIMIZE

BASED ON DEPTH AND VOLUME

MINIMUM "OFF" LEVEL

DISCONNECT

AND BELOW INLET

OF BASIN

CONTROL & ALARM

POWER SUPPLY

(SINGLE PHASE ONLY)

ALARM LIGHT

NOTE: THREE PHASE PANELS HAVE A

TRANSFOMER WITH SECONDARY FUSING.

CONTROL PANEL USED WITH THREE PHASE PUMPS

*Three phase panel has multi-tap transformer with secondary fusing.

Sequence of Operation for Duplex Panel

1. Operation can begin after the following:

- Correct voltage is supplied to Panel

- Panel is properly grounded

- Pumps are connected correctly to Panel

- Panel Circuit Breakers are closed

- Floats are installed properly

- Overload Protection is adjusted to Pump nameplate amps

- Pump HOA Switches are set to “Auto”

- Control On/Off Switch is set to “On”

2. When the “Stop” and “Lead” oats are closed Pump 1 will energize

and the Pump 1 Pump Run Light will illuminate. Pump 1 will remain

operational until the “Stop” oat opens.

3. The next time the “Stop” and “Lead” oats are closed the Alternating

Circuit will energize Pump 2 and the Pump 2 Pump Run Light will

illuminate. Pump 2 will remain operational until the “Stop” oat opens.

This cycle will repeat each time the uid level rises and falls.

4. If the uid level continues to rise after the rst pump has been ener-

gized the “Lag” oat will close. When the “Lag” oat has closed the

second Pump will Energize. Both Pumps will remain operational until

the “Stop” oat opens.

5. In a three oat system when the “Lag” oat is closed the following will

also occur:

- The External High Water Light will illuminate

- The Audible High Water Horn will sound

- The Auxiliary Dry Contacts will close

6. In a four oat system, the alarm oat should be the third oat causing

an alarm to sound when the lead pump fails to operate or the rate of

in ow into the basin exceeds the capacity of one pump. When the

alarm oat is closed the following will occur.

- The External High Water Light will illuminate

- The Audible High Water Alarm will sound

- The Auxiliary Dry Contacts will close

As the liquid level continues to rise the fourth oat will close, energizing

the lag pump. The lag pump and the lead pump will remain energized

until the "Stop" oat opens.

NOTE: In Duplex systems where it is considered normal for two pumps

to operate in tandem during peak ow conditions, the third and fourth

oat may be reversed.

7. The Audible High Water Horn can be silenced by pressing the Alarm

Silence Button. When the “Alarm” oat opens the External High

Water Light, Audible High Water Horn and Dry Auxiliary Contacts will

be reset.

NEMA 4X ENCLOSURE (Float Switches not included)

Order

No.

Dimensions

H x W x D

Volts* Amp Range

10-1102

10-1104

10-1106

10-1108

10-1110

10-1111

10-1112

10-1114

10-1115

10-1183

14" x 12" x 6"

200/230/460

200-208

1.0 - 1.6

1.6 - 2.5

2.5 - 4.0

4.0 - 6.3

6.0 - 10.0

9.0 - 14.0

13.0 - 18.0

17.0 - 23.0

20.0 - 25.0

23.0 - 32.0

10-1154

10-1156

10-1158

14" x 12" x 6"

575

1.6 - 2.5

2.5 - 4.0

4.0 - 6.3