3 4WD 4 Instructions for installation and use English EN
Summary PRECAUTIONS BEFORE USE .............................................................................................................. 2 1.1 IMPORTANT SAFETY INSTRUCTIONS ............................................................................................................... 2 1.2. CONTENT OF THE PACKAGE ........................................................................................................................... 2 1.3. ASSEMBLING THE CADDY ..........................
PRECAUTIONS BEFORE USE 1.1 IMPORTANT SAFETY INSTRUCTIONS x The control box must not be positioned in an area likely to flood. x If the control box falls into the water it is imperative that you unplug the power supply before retrieving it. x In order to avoid the risk of an electric shock, never open the electronic control box. Consult a qualified technician. x Never attempt to repair the power supply cable.
g) Place the 2 caps on the wheels as shown on Diagram 4. h) Position blocks (10) and (11) using the 4 screws, paying attention to the arrows and orientation, Diagram 5 or 6 (according to model). Tighten the screws using a Philips screwdriver. Diagram 1 a Diagram 4 Diagram 5 = Vortex™ 3, Vortex™ 4 Diagram 6 = Vortex™ 3 4WD USE 2.1.
2.2. IMMERSING THE CLEANER Do not allow bathing when the cleaner is in the pool. Immerse the cleaner in the water (Diagram 7 1) vertically and move it slightly in all directions (7 2) so that the air in the robot is expelled. Diagram 7 EN It is imperative that the cleaner sinks to the bottom and comes to rest without intervention from you. Spread the cable out over the pool.
2.4.2. Start up x When the cleaner is powered on, the control box remains in standby. x The cleaner is started by pressing the key corresponding to one of the 2 Diagram 10 cleaning programmes (Diagram 10). The indicator located above the selected programme will light up. The cleaner starts after a few seconds and calculates its own trajectory. x You can change the selected cleaning programme at any time when the cleaner is operating.
Wait approximately 15 minutes after the end of the programme before removing the cleaner from the water. • If you wish to run a new programme once the cleaner has stopped press the corresponding button. Before removing the cleaner from the pool, disconnect the power cable and disconnect the floating cable from the control box. Bring the cleaner towards you, by gently pulling on the cable (Diagram 13 1).
2.6.1. Procedure for activating this mode x Connect the control unit to the main power supply. x If you want the robot to automatically run a bottom only cycle, press + (more than 3 seconds). x If you want the robot to automatically run a bottom and walls only cycle, press seconds). + (more than 3 x The 2 diodes will flash simultaneously: x The cleaner will now start automatically in conjunction with the time selected. 2.6.2.
Place the rear wheels on the support wedges (Diagram 15 1). Tilt the robot, then push it backwards until it reaches it storage position (15 2). Diagram 15 The cleaner cable must be disconnected from the control box before removing the cleaner from the pool. EN Wind the cleaner cable around the hooks located at the rear of the caddy starting from the cleaner. 3.3.
4.2.2. Assembling the new tyres Present the tyres on the wheel (Diagram 20 1). Pay attention to the orientation of the tyre: make sure that the “inside” mark on the walls is on the inner side of the wheel. Push one section of the tyre around the wheel and fit the rib of the tyre in the groove of the wheel (20 2). Install the rest of the tyre on the wheel and verify the rib of the tyre fit well with the groove of the wheel (20 3).
Issue: The flashing lights appears just after starting the cleaner (< 20 seconds). Solution: x Ensure the floating cable is connected to the control unit. x Disconnect the floating cable from the control unit and connect it again properly. x Ensure the cleaner is well submerged.
In particular, the spare parts warranty will only be honoured after analysis and inspection of the returned spare parts by our company followed by the decision to replace said parts. In all cases the seller's legal warranty will continue to apply. In order to benefit from the warranty, the Client and the End User agree to respect the following parameters concerning the water balance of the swimming pool: pH: 6.8 < pH < 7.6 free chlorine (* : < 3,0 mg/L total bromine (*): < 5.
CAUTION: USE OF THE VORTEX™3, VORTEX™4 and VORTEX™ 3 4WD CLEANER IN A VINYL LINER POOL Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objects coming into contact with the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply by rubbing the surface with a pool brush.
N o t e s - N o t e n - A a n t e k e n i n g - N o t a s - N o t a
N o t e s - N o t e n - A a n t e k e n i n g - N o t a s - N o t a
Your retailer/ votre revendeur Pour plus de renseignements, merci de contacter votre revendeur. For further information please contact your retailer. Hinweise und Auskünfte erhalten Sie bei Ihrem Händler. Voor nadere inlichtingen kunt u zich wenden tot uw zwembadbouwer. Para cualquier información adicional contactar con su detallista. Contacte o seu revendador para obter informaçoes mais detalhadas. Per qualsiasi informazione supplementare, mettetevi in contatto con il vostro rivenditore al dettaglio.
