TRi Chlorine Generator Instruction Manual and Warranty Card
This Kit Contains: Part: Qty: Description: a. 1 TRi Power pack b. 1 Chlorine generating cell c. 1 Power pack bracket d.
Welcome to Zodiac Congratulations on your purchase of a product from the Zodiac range of pool care products. Zodiac products are designed to let you spend more time enjoying your pool and less on maintenance. Important Information YOU MUST READ THIS INFORMATION BEFORE INSTALLATION. ALWAYS READ THE LABEL AND OPERATION MANUAL BEFORE USING. PLEASE KEEP YOUR MANUAL AS IT CONTAINS YOUR WARRANTY.
Zodiac Believes In Safety First At Zodiac, we take safety seriously. Always exercise caution when using electrical appliances and follow the instructions. Failure to do so could result in permanent injury, electrocution or drowning. General Warnings Zodiac saltwater chlorine generators are designed for domestic swimming pool use only. Contrary use could affect performance and void warranty.
Zodiac Believes In Safety First Child Safety Children should not be allowed to operate or perform maintenance on this product. No one, particularly children, should sit, step, lean, or climb on any of your pool’s operational system. In the interests of child safety, all components of a pool’s operational system should be located at least 3.5 metres away from the pool.
Installation Guide The following steps will help you get up and running with your new Zodiac TRi Chlorine generator. Positioning the power pack 1. Locate a suitable space for the power pack bracket. It should be installed no further than 1.8 metres away from the cell - ideally in a filtration shed or close to the filtration equipment. PLEASE NOTE: if fixing to a post it must have a waterproof panel fitted (behind the unit), at least 450mm wide and 470 mm high. 2.
Navigation Buttons Use the following UI buttons to access and select all menus and commands: On/Off Turn UI power on/off. Up/Down Scroll up/down within current menu to highlight a specific menu command. Menu/Back Enters into the main menu, and used to go back to previous menu. Select/Enter Select/enters current highlighted menu command.
Using inbuilt Clock and TimerS When it comes to chlorination, every pool is different. To get what’s right for you, you will need to set the unit’s clock and timers. Setting The Clock power on. 1. Switch 2. Wait for the start-up sequence to complete. button to enter the MAIN MENU. 3. Press the 4. Use / . 5. Press 6. Use 7. Press 8. Use the 9. Press buttons and scroll to SET CLOCK. / buttons to set the hours. to save the hours. / buttons to set the minutes. to save the minutes.
Using inbuilt Clock and TimerS Turning Chlorine generation ON The chlorine generation of the TRi can be controlled in a number of ways: 1. Manually set to an output level, with the operating times determined by an external timer. 2. Using the in-built timers on the TRi unit (refer to ‘The Timers’) 3. Using a connection to an external controller (refer to ‘Connecting to a controller’). To turn the chlorine generation on manually, press the ON/OFF button.
Using inbuilt Clock and TimerS To program the timer: button. 1. Press the 2. Press button to move arrow to ‘SET TIMERS’. 3. Press to enter the ‘SET TIMERS’ menu. 4. Press / to select the timer you wish to set. (Timer 1 or Timer 2) 6. Press / to set the hours (on time). 7. Press to save the hours. 8. Press / 9. Press to save the minutes. 10. Press / 11. Press to save the hours. 12. Press / 13. Press to save the minutes. 5. Press . to set the minutes (on time).
Using inbuilt Clock and TimerS Clearing The Timers To clear the timer: 1. Press the button. 2. Press / 3. Press to enter the ‘SET TIMERS’ menu. 4. Press / 5. Press button to scroll to ‘SET TIMERS’. to scroll to ‘CLEAR TIMERS’. . A confirmation message will appear on the screen. External Time Clock At times, it may be desirable to control chlorine generation using an external time switch.
Chlorine Output Levels Setting the Chlorine Output The amount of chlorine required by your pool is dependent on a number of factors including the size of the pool, the number of users and the climate. Output will appear as a percentage on the screen readout, monitor the level according to the reading over time will help ensure optimum output. For users who upgrade to the TRi-PRO model, chlorine output will be controlled automatically. To set Chlorine Output levels: 1.
11 Frequency of testing (in peak season) To decrease* Weekly Weekly Add muriatic acid or dry acid Add muriatic acid Weekly Add sodium bicarbonate 80 – 140 80 – 300 Total Alkalinity (ppm) Add buffer or soda ash (sodium carbonate) 7.5 1–3 Ideal reading/range To increase* 7.2 – 7.
Connecting to a controller If you use an automation or controller system to control your pool you will need to configure your TRi Chlorine generator to allow “communication” between the two. You must set the controller type on the TRi before making the wiring connection. Setting the Controller (To be done before making a wiring connection) 1. Switch power to the TRi unit on. 2. Wait for the start-up sequence to complete. 3. Press the button. 4. Press the button to scroll down to ‘CONTROLLER’. 5.
Connecting to a controller Attention Jandy ‘REV L’ or later Users It is critical that the controller setting be set to the correct Zodiac, Jandy or Pentair controller designation. There are a number of different revisions locked into the TRi software. Please see the user manual to determine the model and/or revision you are using. If the incorrect setting is selected, damage can be caused to the Jandy Aqualink Control Unit.
Connecting to a controller 3. Remove the lower cover from the TRi unit. NOTE: If using either pH upgrade or PRO unit – carefully disconnect the ribbon cable from the TRi unit. 4. Remove the small white bung closest to the centre of the lower panel of the TRi unit. 5. Thread the controller cable through the hole (a grommet may be necessary depending on the size of the cable being used). 6. Attach a cable tie to the controller cable as shown in the diagram.
Connecting to a controller Testing the Wiring Connection Once a connection has been made between the Controller and the Chlorine generator, it will need to be tested. 1. Turn on the power to the Controller and the Zodiac TRi. 2. If successful, a ‘ ’ symbol will appear in the top right hand corner of the screen after about 20 seconds. 3. If the controller does not connect, turn power off to both the devices and try again. Verify the Wiring Connections To verify the connection: 1.
Setting the Mode to Low: Important if using a pool cover If your pool has a cover, you should set the output level to “low”. This is also known as “winter” mode. Reducing your chlorine output will help prevent damage to your pool’s cover and other equipment. Manual Setting 1. To select Low mode press . This will drop the chlorine output to around 10%. 2. ‘Low’ will appear on the screen. Note: Low or Winter mode cannot be selected when TRi is being controlled by an external controller.
The Boost Setting At times your pool may require a larger than normal application of chlorine. The Boost function is used to rapidly add chlorine. In BOOST or “Superchlorinate” mode, output settings are temporarily overridden and the chlorine generator runs for 24 hours at 100% Chlorine Production. In ‘TIMER’ mode, the circulation pump will run for 24 hours, before automatically reverting to previous output / timer settings.
Help and Troubleshooting The Zodiac TRi chlorine generator automatically provides a number of inbuilt warnings that can help identify problems and offer solutions. To access the HELP menu: 1. Press the button. 2. Using the / buttons, scroll to the ‘HELP/DIAG’ menu. to enter the ‘HELP/DIAG’ menu. 3. Press 4. Once in the ‘HELP/DIAG’ menu, use the / buttons to scroll to the error/warning that has been displayed. 5. Press .
Maintenance To keep your TRi Unit in the best possible condition it is recommended regular maintenance should be performed. Inspecting and Cleaning The Electrode In areas that experience calcium hardness the TRi electrode will benefit from cleaning. To clean your electrode: 1. Switch off the filter pump and chlorine generator, close necessary valves and unplug the cell terminal cap. 2. Unscrew the retaining ring and remove the electrode.
Errors and Warnings. What They Mean. No Flow Diagnosis: Insufficient water flow in the cell. This could mean the circulation pump has ceased to function, or the filter needs cleaning. The chlorine output will be turned off at this time. Check Salt Diagnosis: Salt level is between 3000 and 4000 ppm, depending on the water temperature. Always maintain a salt level above 4000ppm. if you don’t know what your salt level is or how to test it, consult your local pool care professional.
Troubleshooting Additional information about this product can be found at zodiac.com.au For further information and assistance please consult your local pool professional.
Zodiac Australia - Express Warranty and Guarantees Express Warranty* Zodiac Group Australia Pty Ltd (Zodiac Australia) warrants that the Zodiac TRi Saltwater Chlorine Generator will be free from defects in materials and workmanship for the period of 3 years from the date of purchase. * The warranty applicable to commercial application is limited to 12 months from the date of installation.
Zodiac Australia - Express Warranty and Guarantees 4 Without limiting 3 above, products sold by Zodiac Australia are designed for use with swimming pool water balanced in accordance with Australian Standard AS3633-1989 with a pH range of 7.0 - 7.8. Maximum chlorine readings should not exceed 4ppm.
Zodiac Australia - Express Warranty and Guarantees How to make a warranty claim 9 The Purchaser must telephone or email Zodiac Australia Customer Service and obtain a warranty ID number for the warranty claim. Contact details are: Zodiac Group Australia Pty Ltd 219 Woodpark Road Smithfield NSW 2164 Customer Service Telephone: 1800 688 552 Email address: aftersales@zodiac.
Zodiac Australia - Express Warranty and Guarantees Additional guarantees, rights and remedies Australian Purchasers - Guarantees under the Australian Consumer Law 12 The benefits of this express warranty are in addition to other guarantees, rights and remedies Australian consumers have under the Australian Consumer Law. 13 Zodiac Australia products come with guarantees that cannot be excluded under the Australian Consumer Law.
Zodiac is a registered trademark of Zodiac Group Australia Pty Ltd ABN 87 002 641 965 Zodiac Customer Service Centre Zodiac Group Australia: 219 Woodpark Rd, Smithfield, NSW 2164 Australia Tel: 1800 688 552 Fax: 1300 781 688 Email: aftersales@zodiac.com.au www.zodiac.com.au © Copyright Zodiac Australia Ltd 2013 W176781 REV.A Due to constant developments and improvements, specifications may change without notice. Improper use could affect performance and void warranty.
pH Upgrade Instruction Manual and Warranty Card
This Kit Contains: Part: Qty: Description: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 1 1 1 1 1 1 1 1 1 TRi-pH Module (if purchased separately) Hole saw Tubing POD assembly pH sensor pH sensor cable Sensor calibration fluid Anti Fume Cap 5lt and 15/20lt Ceramic Weight Weight barb fitting (for end of tube) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Welcome to Zodiac Congratulations on your purchase of a product from the Zodiac range of pool care products. Zodiac products are designed to let you spend more time enjoying your pool and less on maintenance. Important Information YOU MUST READ THIS INFORMATION BEFORE INSTALLATION. ALWAYS READ THE LABEL AND OPERATION MANUAL BEFORE USING. PLEASE KEEP YOUR MANUAL AS IT CONTAINS YOUR WARRANTY At Zodiac, we take safety seriously.
Zodiac Believes In Safety First Child Safety Children should not be allowed to operate or perform maintenance on this product. No one, particularly children, should sit, step, lean, or climb on any of your pool’s operational system. In the interests of child safety, all components of a pool’s operational system should be located at least 3.5 metres away from the pool.
Important things to remember There are a number of very important things to remember when setting up and maintain your TRi-pH. 1. It is absolutely essential to have the pool water in good balance before turning the TRi-pH on so ensure that the pool water is correctly balanced (see page 10 of the TRi owners manual for complete list). 2. Do NOT under any circumstances store the acid container underneath the power pack unit.
Quick Start Installation Guide The following steps will help you get up and running with your new Zodiac TRi pH Upgrade Module. If you purchase your Zodiac TRi pH as a complete unit go straight to section - Installing Sensors. If you have purchased the Tri pH upgrade: How to install the TRi pH upgrade unit: 1. Turn mains power off and remove the existing top cover. 2. Unscrew the bottom 2 screws on the main body panel and remove the bottom cover. 3.
Installing the pH Sensor POD Installing the POD and sensor TRi sensor POD integrates into a simple unit, a pH sensor and a pH corrective solution one way valve. The sensor POD must be positioned after filtration system and before TRi cell (and after any heating system). Sensor POD must always be positioned onto a horizontal pipe so that the pH sensor is vertical (45° maximum tolerance).
Preparing pH Sensor 1. Identify a straight section of horizontal pipe of appropriate length after the filter but before the salt cell (30cm is recommended). 1 2. Disassemble sensor POD to get lower part of POD clamp with 2 holes (picture 1). 3. Place the lower part of POD clamp upside down into position on the selected length of piping 2 4. Now mark the location of the 2 holes to be made into piping using a pencil or marker (picture 2). 5. Drill the 2 holes using the provided hole saw.
FITTING THE Acid DELIVERY SYSTEM Now the POD is in place and the sensor is connected it is time to connect the suction and injection tubes 1. To connect the suction and injection tubes please ‘soften’ the ends of the tubing by immersing in warm water for a few minutes. 2. Remove the small face panel that covers the peristaltic pump 3. The suction tube is connected to the left hand side of the peristaltic pump. A 4.
FITTING THE Acid DELIVERY SYSTEM 8. Once all connections are made place the suction line into the container and screw the anti fume cap down into position. (see picture C) C Please take note of these important points when connecting pH control • ONLY use straight hydrochloric (muriatic) acid, do not dilute or use any other type of acid.
Testing / Priming the Acid Pump After installation it’s recommended the acid pump be tested and the acid pump ‘primed’. WARNING! Before testing the pump, ensure all acid supply and delivery connections are secure. Always use appropriate safety equipment when handling acid. To test the Acid Pump: 1. Press the button. 2. Press / 3. Press to enter the ‘pH SETUP’ menu. 4. Use the buttons to move arrow to ‘pH SETUP’. / buttons to highlight ‘TEST ACID’ and press to enter test acid menu. 5.
pH Control The following information about pH is critical to the successful operation of your swimming pool. For advice and supply of the correct products, consult your local pool care professional. Preparing the Pool The TRi-pH unit is designed to maintain the pH of the pool. By ensuring that the pool is correctly balanced at the outset will decrease the chance of problems, during the first days of operation. pH Levels Ideal pH range for most pools is 7.2 – 7.
pH Control Chlorine Levels Ideal chlorine level range: 1-3 parts per million (PPM). Prior to starting the TRi-pH the chlorine level can be raised using either liquid or granulated chlorine. Salt Levels Ideal Salt level range: 3000 – 5000 parts per million (PPM). Efficient and correct operation of the electrolytic cell requires a sufficient amount of salt in the water. Not enough salt may cause a reduced chlorine output level and a reduced life of the cell.
With pH sensor and acid delivery components successfully set up, the TRi unit needs to be calibrated and set up for pH control. Ensure that mains power is supplied to the TRi, turn the pool pump off and isolate the pool water so the pH sensor can be safely removed. 1. Remove the pH sensor and clean if necessary using soapy water. (Avoid touching the glass tip of the sensor). Rinse off with fresh water. 2. Place the pH sensor in a sample of pH calibration solution with a pH level of 7.5. 3.
pH Set Point The default pH setting of your Zodiac TRi is 7.2. This can be changed according to your pool’s requirements. To change the pH set point: 1. Calibrate the pH sensor. 2. From the default operating screen, press . 3. Use the / buttons to highlight ‘pH SETUP’, then press 4. Use the / buttons to highlight ‘pH SETPOINT’, then press 5.
pH Set Point Setting the pool size This setting controls the maximum amount of acid which is delivered to the pool daily. Your unit comes factory set on pool size 2. The recommended settings for various size pools are as follows: 1: 2: 3: 4: For small pools up to 40 000 litres For medium pools 40 000 to 60 000 litres For large pools 60 000 to 100 000 litres For over size pools above 100 000 litres The above settings are a guideline only.
pH Set Point WARNING! It is advised that the pool size be set as low as possible to avoid overdosing acid into the pool. Using pH control The TRi-pH is now ready for use with automatic pH control. 1. Set ‘ON’ and ‘OFF’ times. 2. Select desired chlorine output level. 3. Enable the Acid Pump (Refer to Enabling and disabling the Acid Pump.) The TRi unit will now automatically maintain the pH level of the pool.
Regular Check Ups Although automatic pH control reduces the need for regular testing, there are still a number of checks to ensure the safe operation of the system and a pleasant swimming experience. Always check: Acid supply levels. Total Alkalinity. The accuracy of the pH sensor by manually checking the pH level. That the pH sensor is cleaned and re-calibrated. Acid Pump and Feed Line Maintenance 1. Lubricate the pump squeeze tube every 6 months.
Adjusting Total Alkalinity (TA) As acid is added automatically over time, total alkalinity levels will decrease and may result in inconsistent pH levels. It may be necessary to add a “buffer” element to the water in your pool. As it is not recommended to add acid after adding a “buffer”, temporarily disable the acid pump (refer to Enabling and disabling the acid pump). Enabling and disabling the Acid Pump. In the interests of safety, the Zodiac TRi-pH is shipped with the acid pump disabled.
When using automatic pH control, the requirement for regular pool chemistry checks is lowered. It is however, necessary to regularly check a number of critical things to ensure safe and correct operation of the system: Cleaning the pH Sensor When cleaning the sensor avoid using solvents such as acetone. Always calibrate after cleaning. To clean the sensor: If the electrode has become coated with oil or grease, carefully wash the electrode under warm tap water using dish-washing detergent.
Errors and Warnings. What They Mean. pH Low Diagnosis: the pH Level in the pool has dropped too far below the set point. This could indicate the POOL SIZE setting is too high, causing acid to overdose or the pH sensor is faulty or needs calibration and/or cleaning. Manually test the pool’s pH before further investigation, if all equipment is operating fine then adjust your pool setting to a lower value. pH Error Diagnosis: the acid pump has completed its dosing cycles without reaching the set point.
Express Warranty and Guarantees Express Warranty Zodiac Group Australia Pty Ltd (Zodiac Australia) warrants that the TRi-pH Chlorinator will be free from defects in materials and workmanship. The Cell and Power Pack is warranted for the period of three (3) years, if used in a domestic/residential pool. The Peristaltic pump, sensors and other extraneous equipment are conditionally warranted for the period of twelve (12) months, if used in a domestic/ residential pool.
Notes _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _
Zodiac Customer Service Centre Zodiac Group Australia: 219 Woodpark Rd, Smithfield, NSW 2164 Australia Tel: 1800 688 552 Fax: 1300 781 688 Email: aftersales@zodiac.com.au www.zodiac.com.au Due to constant developments and improvements, specifications may change without notice. Improper use could affect performance and void warranty.
