Specifications

7.3.1 Off Mode
When the control panel is turned off, the screen
displays
GAS HEATER IS OFF PRESS POOL OR
SPA
.
7.3.2 Pool Mode - (Normal Heat)
To enable the pool mode, press POOL. The
associated left green LED indicator will light and the
unit will display
SET:XXX°.
NOTE XXX represents the current temperature setting
on the control. The default setting for pool
temperature is 80°F (26°C).
You can change the temperature set point by
pressing the
Up or Down button. Repeatedly press
the Up or Down
button until you reach the desired
temperature set point. After 5 seconds of inactivity, the
new set point is stored in memory.
When the water temperature falls to 1 degree
below the temperature setting, the control will start the
heater and the associated right LED will light RED
.
7.3.3 Spa Mode - (Normal Heat)
To enable the spa mode, press SPA. The associated
left green LED indicator will light and the unit will
display
SET:XXX°.
NOTE XXX represents the current temperature setting
on the control. The default setting for spa
temperature is 102°F (38°C).
You can change the temperature set point by
pressing the
Up or Down button. Repeatedly press
the
Up or Down button until you reach the desired
temperature set point. After 5 seconds of inactivity, the
new set point is stored in memory.
When the water temperature falls to 1 degree
below the temperature setting, the control will start the
heater and the associated right LED will light RED.
7.4 User Setup Options
The User Setup options allow the user to select
specic Languages, Temperature Scale, Spa Timer, and
Display Light options.
7.4.1 Language Setup
1. Make sure the control is in the OFF mode.
2. To enter the User Setup mode, press and hold the
MENU button for 5 seconds.
NOTE The display will revert back to OFF after one
minute since the last key press.
3. To select a language, use the Up or Down button
to display
SELECT USER SETUP LANGUAGE.
Press the
MENU button. The SELECT
LANGUAGE ENGLISH
(default language)
appears, use the
Up or Down button to scroll
through the language options. When you reach the
desired language, press the
MENU button to select
the language. Press
POOL or SPA to exit the User
Setup mode.
7.4.2 Temperature Scale Setup
1. Make sure the control is in the OFF mode.
2. To enter the User Setup mode, press and hold the
MENU button for 5 seconds.
3. To select temperature scale, use the
Up or Down
button to scroll through to display SELECT
USER SETUP TEMPERATURE SCALE
. Press
the MENU button. The SELECT TEMP SCALE
°F:
(default temperature scale) appears, use the
Up or Down button to scroll to display SELECT
TEMP SCALE °C:
. When you reach the desired
temp scale, press the MENU button to select. Press
POOL or SPA to exit the User Setup mode.
7.4.3 Spa Timer Setup
1. Make sure the control is in the OFF mode.
2. To enter the User Setup mode, press and hold the
MENU button for 5 seconds.
3. To select spa timer, use the
Up or Down button
to scroll through to display SELECT USER
SETUP SPA TIMER
. Press the MENU button. The
SELECT SPA TIMER CONTINUOUS: (default
spa timer setting) is displayed. To turn the spa
on or off indenitely, press the MENU button to
select.
To select the length of time for the spa to run,
use the
Up or Down button to scroll to display
SELECT SPA TIMER TIME SELECTION. Press
the MENU button to select. The display SELECT
SPA TIME 01:00 HRS:
(default time setting) is
displayed. Use the Up or Down button to select
the length of time for the spa to run (between
00:15 to 23:00 hours incremented by 00:15
minutes). Press the MENU button to select how
long the spa will run. Press POOL or SPA to exit
the User Setup mode.
7.4.4 Display Light Setup
1. Make sure the control is in the OFF mode.
2. To enter the User Setup mode, press and hold the
MENU button for 5 seconds.
3. To select display light setup, use the
Up or Down
Page 26
ENGLISH
Jandy
®
Legacy™ Model LRZE Pool/Spa Heater by Zodiac
®
|
Installation and Operation Manual