ZX4300P 10/100 ETHERNET SWITCH USER'S GUIDE Layer 2 CPSB Switch Document No: DC0138-04
Copyright Notice ZNYX Networks 48421 Milmont Drive Fremont, CA 94538 USA Telephone: Fax: Email: Website: (510) 249-0800 or (800) 724-0911 (510) 656-2460 sales@znyx.com support@znyx.com www.znyx.com ZX4300P Series User's Guide Document # DC0138-04 September 26, 2001 ©2001 ZNYX Networks. All rights reserved worldwide. Information in this document is subject to change without prior notice.
About this Manual This manual includes the installation, troubleshooting, and reference data for the ZX4300P 10/100 Ethernet Switch. See the ZNYX Networks data sheet for product specifications. All documentation for ZNYX Networks products, including data sheets, release notes and User's Guides are available for downloading from the ZNYX Networks website (http://www.znyx.com). Files are supplied in PDF format so your system requires Adobe Acrobat Reader to open and read the documentation.
Overview Chapter 1 Overview of the ZX4300PSwitch The ZX4300P CompactPCI Ethernet 10/100 Mbps switch is the cost-effective and flexible solution to Embedded Carrier Class Layer 2 switching requirements. ZNYX Networks' ZX4300P is the first switch designed to support the upcoming PICMG 2.16 specification for a CompactPCI Packet Switching Backplane (CPSB), but it can also be deployed in a standard CompactPCI chassis by using one of three optional Rear Transition Boards (RTB).
Overview Features of the ZX4300PSwitch The ZX4300P switch best satisfies the demand for high density, low cost, and high performance. It enables system architects to accelerate development of their next-generation CPSB products and achieve first-to-market deployment. • Designed for use in CompactPCI PICMG 2.
Installation Chapter 2 Installation The ZX4300P is an unmanaged layer 2 switch requiring no software setup or configuration. Once the switch is installed in a chassis and power applied, it is fully operational as a layer 2 switch. Be sure to carefully follow the instructions for attaching the ZX4300P switch into an available 6U Compact PCI (cPCI) slot to prevent damage. For CPSB applications, the ZX4300P must be placed in a PICMG 2.16 compliant fabric slot.
Installation Installing the Rear Transition Board (RTB) 1. Remove the slot cover (or covers) from the corresponding rear panel bracket (slot filler) on your system. 2. Insert the correct Rear Transition Board into the slot. NOTE: Exercise extreme care when inserting the RTB card into the chassis. Improper alignment of the rear transition card connector with the rear panel connector pins can damage the pins. Your switch includes AB connectors to assist in properly aligning the RTB for insertion.
Installation Connecting the Cables The ZX4300P uses Broadcom's proprietary HP-AutoMDI-X technology that senses the cable attachment and adjusts it's internal Transmit and receive paths accordingly. The ports of the switch will auto-sense and correct for MDI (straight-through) or MDI-X (crossover) cabling. LED Reference The LED lights on the ZX4300P switch and corresponding Rear Transition Board (RTB) provide diagnostic and activity information during power up and normal use of the switch.
Installation ZX4300P Series LED Reference Key LED Color Function Power up Display LNK (0-23) Green ON indicates a link is established with the corresponding port. OFF during power up. ACT (0-23) Yellow Flashing indicates activity on the channel. OFF during power up. SPD100 (0-23) Green ON indicates the ethernet channel is successfully linked at 100 Mb/s OFF during power up.
Legal Notices and Certifications A. Legal Notices and Certification FCC Class A Notice: ZX4300P SERIES Pending THE ZX4300P IS FOR USE ONLY WITH COMPACT PCI BUS COMPATIBLE SYSTEMS THAT HAVE ENCLOSED POWER SUPPLIES WITH SELV OUTPUTS AND INSTALLATION INSTRUCTIONS DETAILING USER INSTALLATION OF CARD CAGE ACCESSORIES.
Connector Pinouts B.
Connector Pinouts 25 GND LP20_DA+ LP20_DA- GND LP20_DC+ LP20_DC- GND 24 GND LP20_DB+ LP20_DB- GND LP20_DD+ LP20_DD- GND 23 GND LP21_DA+ LP21_DA- GND LP21_DC+ LP21_DC- GND 22 GND LP21_DB+ LP21_DB- GND LP21_DD+ LP21_DD- GND 21 GND LP22_DA+ LP22_DA- GND LP22_DC+ LP22_DC- GND 20 GND LP22_DB+ LP22_DB- GND LP22_DD+ LP22_DD- GND 19 GND LP23_DA+ LP23_DA- GND LP23_DC+ LP23_DC- GND 18 GND LP23_DB+ LP23_DB- GND LP23_DD+ LP23_DD- GND 17 GND LP24_DA+ LP24_DA
Connector Pinouts 19 GND SGA4(4) SGA3(4) SGA2(4) SGA1(4) SGA0(4) GND 18 GND LPf_DA+ LPf_DA- GND LPf_DC+ LPf_DC- GND 17 GND LPf_DB+ LPf_DB- GND LPf_DD+ LPf_DD- GND 16 GND LP8_DA+ LP8_DA- GND LP8_DC+ LP8_DC- GND 15 GND LP8_DB+ LP8_DB- GND LP8_DD+ LP8_DD- GND 14 GND LP7_DA+ LP7_DA- GND LP7_DC+ LP7_DC- GND 13 GND LP7_DB+ LP7_DB- GND LP7_DD+ LP7_DD- GND 12 GND LP6_DA+ LP6_DA- GND LP6_DC+ LP6_DC- GND 11 (2) LP6_DB+ LP6_DB- GND LP6_DD+ LP6_DD-
Connector Pinouts Node & Fabric Board J2 Pin Assignment GND GA4(3,7) GA3(3,7) (7,16) (7,16) GND (7,16) (7,16) GND (7,17) (7,17) GND 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Pin GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND Z(5) GA2(3,7) GA1(3,7) GA0(3,7) (7,16) (7,16) (7,16) (7,16) (7,16) (7,16) SMB_ SDA(7,18) SMB_ (7,18) SCL SMB_ (7,18) ALERT (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17) (7,17)
Connector Pinouts Node & Fabric Board J1 Pin Assignment 25 GND 5V(8) (7) ENUM#(15) 3.3V(8) 24 23 22 21 20 19 18 17 GND GND GND GND GND GND GND GND (7) 5V(8) V(I/O)(8) (7) (7) 3.3V(8) (7) (7) 5V(8) (7) (7) GND(8) 3.3V(8) (7) (7) 3.3V(8) (7) (7) (7) (7) (7) GND(8) V(I/O)(8) (7) (7) 3.3V(8) (7) (7) GND(8) (7) (7) GND(8) IPMB_ SCL(7) (7) (7) GND(8) (7) 16 GND GND(8) 3.3V(8) IPMB_ SDA(7) V(I/O)(8) (7) (7) GND 15 GND 3.
Connector Pinouts Notes for J Connector Pinouts from Previous Tables Sections referenced below pertain to the CompactPCI Packet Switching Backplane PICMG 2.16 Draft 0.6.5 June 19, 2001 1. BP(I/O) connects Front card to Rear card and does not connect to backplane. Refer to Section 3.1.1.2 for Alternate Node Board Keying Compliance. 2. GND for Type B style J3 connector. 3. Refer to Sections 3.3.2.3, 3.3.3.7, 3.3.5.1, 3.3.6.1, 4.3.5, 4.3.6, 4.4.1, and 4.4.10. 4. Refer to Sections 3.3.3.8, 3.3.6.2, 4.3.7, 4.4.
Patch Panel Cable Specifications C. Patch Panel Cable Specifications The specifications required to build a cable for attaching the ZX4300P Series ZXRTB24R Rear Transition Board to a standard patch panel are on the following page. Contact your ZNYX Networks Sales Representative for assistance, or visit http://www.panduit.com. The diagrams below illustrate the cables when they are properly attached.
Patch Panel Cable Specifications Ordering Information (from www.panduit.com) Depth Length Width Width Height Height No. of (in) (ft) (in) (mm) (in) (mm) Ports Part Number Part Description DP24584TV25 19" (482.6mm) W X 1.39" 1.39 (35.3mm) D X 1.72" (43.7mm) H 19 482.6 1.72 43.7 24 DP48584TV25 19" (482.6mm) W X 1.39" 1.39 (25.3mm) D X 3.47" (88.1mm) H 19 482.6 3.47 88.
