RANGE HOOD Installation Guide and Users Manual
WARRANTY AND DISCLAIMER CONTENTS Warranty Three Year Parts Warranty: For three years from the date of original purchase, we will provide free of charge, non-consumable replacement parts for the components that failed due to IMPORTANT SAFETY INSTRUCTIONS 1 manufacturing defects. Subject to the conditions and limitations set forth below at its WALL RANGE HOOD INSTALLATION 4 of improper workmanship or material.
Warranty and Disclaimer Important Safety Instructions to the purchaser and does not extend to subsequent owners of this product, any Read all instructions before installing and operating this appliance.
Important Safety Instructions Important Safety Instructions All electrical wiring must be properly installed, insulated and grounded. Use an extinguisher ONLY if: Old duct work should be cleaned or replaced, if necessary, to avoid the possibility of You know you have a Class A, B, C extinguisher and you already know how to a grease fire. operate it. Check all joints on duct work to insure proper connection, all joints should be The fire is small and contained in the area where it is started.
Wall Range Hood Installation Wall Range Hood Installation Please unpack your range hood when it is delivered and inspect to ensure all parts are included. Parts Supplied 1. Main Hood with All Lights and Button 5. Flexible Duct (for 6” or 8”) Banks Pre-Installed 6. Packet of Screws and Anchors 2. Adjustable Stainless Steel Chimney Cover 7. Top Mounting Bracket 3. Transition Piece (for 6” or 8”) 8. Grease Cup 4.
Wall Range Hood Installation Wall Range Hood Installation The recommended height to install your hood is 30˝ minimum and 36˝ maximum Step 5 above the cooktop. Install the transition piece securing it with the screws provided. Figure 4 For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of Step 6 36˝ above the grill. Make your electrical and ducting connections. Try and minimize the use of elbows. Step 1 More elbows and longer runs create higher static pressure.
Wall Range Hood Installation Crown Molding Installtion Before installing baffle filters, make sure that you insert the grease cup under the If using a crown molding, follow instructions before attaching ducting and chimney motor blower. sections. Step 8 Step 1 Install the two part chimneys on top of the hood. Slide the inside section up until the Attach crown molding bracket to ceiling using hardware provided. vertical vent slots are visible, attach top portion to mounting bracket with screws.
Designer Wall Range Hood Installation Designer Wall Range Hood Installation Please unpack your range hood when it is delivered and inspect to ensure all parts are included. Parts Supplied 1. Main Hood with All Lights and Button 6. Packet of Screws and Anchors Banks Pre-Installed 7. Top Mounting Bracket 2. Chimney 8. Crown Molding Bracket 3. Transition Piece (for 6” or 8”) 9. Crown Molding 4. Baffle Filters 10. Grease Cup 5.
Designer Wall Range Hood Installation Designer Wall Range Hood Installation The recommended height to install your hood is 30˝ minimum and 36˝ maximum Step 5 above the cooktop. Make your electrical and ducting connections. Try and minimize the use of elbows. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of More elbows and lon-ger runs create higher static pressure. The hood comes with a 36˝ above the grill.
Designer Wall Range Hood Installation Island Hood Installation Step 8 Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing to hold the weight of the hood. Mark your center line and measure out from the center to find your two mounting points. Make sure your mounting points are level when you mark them. It is recommended to install the hood directly into wood supports.
Designer Wall Range Hood Installation Island Hood Installation The recommended height to install your hood is 30˝ minimum and 36˝ maximum Step 6 above the cooktop. Slide chimney pieces over the angle iron on the hood. Pull the electrical plug to the For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of top of the chimney sections. Figure 4 36˝ above the grill. Step 7 Step 1 Lift the hood to attach the angle iron to the ceiling bracket.
Under cabinet Installation Under cabinet Installation Preparation Decide the location of the venting pipe from the hood to the outside. Check hood for clearance. A straight, short vent run will alllow the hood to perform more efficiently. Try to avoid as many transitions, elbows, and long runs as possible. This may reduce the performance of the hood. For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on each side.
Under cabinet Installation Under-Cab Rear Ducting Conversion If you need to convert your under cabinet range hood to rear ducting please follow Step 5 the instructions below. Please note that converting the Draw electrical wires through cabinet access opening, center the hood beneath the undercab to rear ducting is a modification of the standard cabinet. hood and part of the installation process. It is recomended that the hood is inspected before this procedure.
Range Hood Insert Installation Range Hood Insert Installation When installing a range hood insert, it is recommended to install the unit at a minimum of 30˝ Figure 1 from the cooktop. For outdoor range hood inserts it is recommended to install the unit at a minimum of 36˝ from the grill top. Step 1 Figure 1 Unpack contents of the hood. Attach transition piece and ducting to the otp of the range hood insert.
REMOTE BLOWER INSTALLATION REMOTE BLOWER INSTALLATION When installing your new remote blower type range hood, follow the instructions for Step 5 the type of hood you are installing. If you are installing a wall, Island, under cabinet Run electrical cord (provided) back to the or insert hood then you will follow those instructions. This portion of the manual will range hood (up to 26’). explain how to install the remote blower for your range hood.
REMOTE BLOWER INSTALLATION How to Change Parts How to Change Out the Button Panel 1. Remove baffle/aluminum filters. 2. Locate back of button panel. 3. Remove screws from each side of the button panel. 4. Disconnect button panel from cord connecting to circuit board. Note: Never work on or clean the range hood while power is ON. Always unplug the unit or swtich the electrical breaker to the off position. Installation Tutorial Video The Remote Blower is designed for our Remote Range Hoods.
How to Change Parts How to Change Parts How to Replace the Circuit Board: Replacing the Light Bulbs in Your Range Hood: 1. Turn the power off at the breaker and unplug the Range Hood. Use 20 watt MR11 Halogen Bulb or a 2.5 watt LED Bulb for replacement. 2. Remove all screws from the top of the circuit board cover. 3. Take a picture of the wiring layout (this will help you put the circuit board back together properly). 4. Remove the wiring connected to the circuit board. 5.
How to Change Parts How to Change Parts Professional Series Baffle Filter Change: Baffle Filter: Covering Models 696 / 697 / 697 Island / KECOM / KECOM Island / 695 , The Baffle Filter is equipped with a spring loaded handle. To remove from the hood, 698, and 721 Inserts pull back toward the wall and down. The Baffle Filter can also be opened for easy Professional series hoods are equipped with 2 removable dishwasher safe baffle cleaning.
How to Change Parts How to Change Parts Change/Replace Capacitor: Replace or Change Charcoal Filters: 1. Remove screws from the circuit board cover. It is recommended to direct vent the hood whenever possible. 2. Remove screws from compacitor. If your situation does not allow for a direct vent install, carbon filters are available to 3. Remove both wired connections from the capacitor. recirculate the air through your hood. 4. Connect new capacitor with wire connectors. 5. Replace screws in cover.
How to Change Parts How to Change Parts How to Clean, Install, or Replace the Grease Cup: Replace or Change Transformer: A removable grease cup is provided to catch any excess greatse at the bottom of the 1. Remove the screws from the transformer. motor. Remove it every 2 to 3 months, wash it, then re-install it. 2. Remove the two connections to the lights. Note: Never work on or clean the range hood while power is ON. Always unplug 3.
How to Change Parts How to Change Parts Dual Motor Electrical Diagram: Single Motor Electrical Diagram: Switch Switch 110-120V 60Hz 110-120V 60Hz wh bk wh bk 16 hF/250V C wh Transformer 2x12V max 20W wh br bk rd bu 16 hF/250V C or ye M~ wh Transformer 2x12V max 20W wh br bk rd bu or ye M~ 2x170W 16 F/250V C or ye M~ 36 37
How to Change Parts Button Control Panel Operation: Trouble Shooting and FAQs No Power 1. Check electrical connections. 2. Check that all connections to the cicuit board are secure. 3. If problem still exists, the circuit board needs to be replaced. What size hood should I choose for CFM purposes? 1. You must determine the output of the cooktop burners of your range; this is Button functions measured in British Thermal Units (BTU’s). Power: Power ON/OFF the range hood and activate power-off delay 2.
Trouble Shooting and FAQs Trouble Shooting and FAQs What type of stainless steel are our hoods made of? What is the best way to duct my range hood? Our indoor stainless steel hoods are made with a 430 stainless steel. Our outdoor To maximize your range hood’s performance, match your duct size to the original hoods are made of 304 stainless steel, this type is stronger and more resistant to rust size of the fan’s ducting. Use the shortest amount of ducting as possible and keep the and corrosion.
Trouble Shooting and FAQs How do I order replacement parts? Replacement parts can be ordered by contacting our customer service department. All hoods have a three year warranty on parts. Have your model number or order number available when calling customer service. My range hood will not operate. 1. Check that there is power to the range hood. The most common issue is that the circuit breaker is off or the fuse has blown. 2. Make sure the speed has been selected at the range hood controls. 3.
Z Zl ne Kitchen and Bath Two Locations: 916 Delaware Avenue Marysville, Ohio 43040 350 Parr Circle Reno, NV 89512 www.zlinekitchen.
