Installation Guide

12
Drawer Installation
INSTALLATION
INSTALLATION THE DRAWER
1. Place the drawer near the cabinet opening. Plug the power cord into the electrical outlet.
2. Carefully guide the drawer into the opening. Avoid pinching the power cord.
3. Slide the drawer until the mounting plates are flush with the face of the cabinet.
4. Open the drawer. Using 4 screw holes as a template, pre-drill the cabinet with a 1/16"
bit and secure the drawer with the four screws supplied.
IMPORTANT CABINET CUTOUT NOTES:
• For 30" models, note the difference in width between the front panel (29 3/4",
756 mm) and the product itself (22 1/8", 562 mm). While the minimum cutout
width is 22 3/8" (568 mm), the screw holes to mount the drawer are located on the
edge of the front panel and as such must be secured to the cabinet in this manner.
• For 24" models, note the cutout height (14 3/4", 375 mm) is the same height as
the product itself. This is recommended to ensure a flush installation considering the
front panel height (14 7/8", 378 mm) is only slightly higher. A cutout height of 14
13/16" (376 mm) might be suitable for some installations.
• Always consult a professional installer to confirm dimensions prior to installation.
1. Place the drawer adjacent to the wall or cabinet opening.Plug the power supply cord into the electrical outlet.
2. Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and the wall.
3. Slide the drawer all the way until the mounting
flange is flush with the face of the cabinet.
See Figure 5.
4. Open the drawer. Using the 4 holes on
the drawer as a template , pre drill the cabinet
using a 1/16" bit. See Figure 5.
5. Secure the drawer with the 4 screws supplied.
See Figure 6.
The name plate includes model and serial number. Open the Microwave Drawer fully. The label is beyond the
back wall of the microwave cavity facing up from the flat surface.
Refer to the Operation Manual for cleaning instructions.
4 S c r e ws
4 S c r e ws
Figure 6
MODEL AND SERIAL NUMBER LOCATION
CARE,CLEANING AND MAINTENANCE
DRAWER INSTALLATION
Figure 5
12
4
DRAWER INSTALL ATION
MODEL & SERIAL NUMBER LOCATION
CARE, CLEANING & MAINTENANCE
Figure 4
Figure 5
1. Place the drawer adjacent to the wall or cabinet opening.
Plug the power supply cord into the electrical outlet.
2. Carefully guide the drawer into the prepared opening.
Avoid pinching the cord between the oven and wall.
3. Slide the drawer all the way until the mounting flange
is flush with the face of the cabinet.
4. Open t
4. Open the drawer. Using the 4 holes on the drawer as
a template, pre-drill the cabinet using a 1/16” bit.
5. Secure the drawer with the 4 screws supplied (Figure 5).
To locate the model and serial number, open the microwave drawer fully. The label can be found beyond
the back wall of the microwave cavity, facing up from the flat surface.
Refer to the Operation Manual for cleaning and care instructions.
30" Microwaves
Mounting screws
Mounting plate
4
DRAWER INSTALL ATION
MODEL & SERIAL NUMBER LOCATION
CARE, CLEANING & MAINTENANCE
Figure 4
Figure 5
1. Place the drawer adjacent to the wall or cabinet opening.
Plug the power supply cord into the electrical outlet.
2. Carefully guide the drawer into the prepared opening.
Avoid pinching the cord between the oven and wall.
3. Slide the drawer all the way until the mounting flange
is flush with the face of the cabinet.
4. Open t
4. Open the drawer. Using the 4 holes on the drawer as
a template, pre-drill the cabinet using a 1/16” bit.
5. Secure the drawer with the 4 screws supplied (Figure 5).
To locate the model and serial number, open the microwave drawer fully. The label can be found beyond
the back wall of the microwave cavity, facing up from the flat surface.
Refer to the Operation Manual for cleaning and care instructions.
24" Microwaves
Mounting plate
Mounting screws