Installation Manual MICROWAVE DRAWER www.zlinekitchen.
ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to providing you an elevated experience in the heart of your home. With an endless selection of features and finishes, our inspiration is your reality.
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury designs and professional features into everyone’s homes. Because we continually strive to improve our products, we may change specifications and designs without prior notice. WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ��������������������������������1 BEFORE INSTALLATION ��������������������������������������������������������5 Product Specifications ������������������������������������������������������������������������������������ 5 Electrical Connection ������������������������������������������������������������������������������������� 7 INSTALLATION ����������������������������������������������������������������������9 Cutouts and Clearances ����������������������
IMPORTANT SAFETY INSTRUCTIONS WARNING General Safety • Before installation and operation, please read and follow these important instructions for the safety of your home and the people living in it. • Installation and service must be performed by a qualified installer. The oven should not be adjusted or repaired by anyone except properly qualified service personnel. • IMPORTANT: Save this installation manual for local electrical inspector’s use and for your own future reference.
General Safety IMPORTANT SAFETY INSTRUCTIONS 2 • This appliance must be grounded or connected to a properly grounded outlet. • Install this appliance only in accordance with the provided installation instructions. • Some products such as whole eggs and sealed containers (i.e. closed glass jars) should not be heated in this oven. • Use this appliance only for its intended use as described in the manual. Do not use corrosive chemicals or vapors in this appliance.
IMPORTANT SAFETY INSTRUCTIONS • When cleaning surfaces of the door and oven that come together when closing the door, use only mild, nonabrasive soaps or kitchen-safe cleaners applied with a sponge or soft cloth. Do not clean with metal scouring pads. Pieces can burn off the pad and touch electrical parts, increasing risk of electric shock. • To reduce the risk of fire inside the oven: • Do not overcook food.
IMPORTANT SAFETY INSTRUCTIONS General Safety • Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUID SUDDENLY BOILING OVER WHEN THE CONTAINER IS DISTURBED. • To reduce the risk of injury: • Do not overheat liquid. • Stir the liquid before and halfway through heating it. • Do not use straight sided containers with narrow necks.
BEFORE INSTALLATION Remove the microwave and all materials from the carton and inside the oven. Your appliance comes with the following accessories: 24" Microwaves Touch pad Control box Right mounting plate Handle Window Cord is 48” (1219 mm) long SETTING UP YOUR OVEN BEFROE Names of Oven Parts and Accessories Left and all materials from the carton and oven cavity.
BEFORE INSTALLATION PRODUCT SPECIFICATIONS 24" 30" Rated Voltage 120VAC, 60 Hz, 13A 120VAC, 60 Hz, 13A Rated Input Power 1500W 1500W Rated Output Power 1000W 1000W Oven Capacity 1.2 Cu. Ft. 1.2 Cu. Ft.
BEFORE INSTALLATION WARNING ELECTRICAL CONNECTION • This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. • This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. • Improper grounding may result in electrical shock.
BEFORE INSTALLATION WARNING CLEARANCES AND DIMENSIONS NOTICE For safety considerations, do not install the unit in any combustible cabinetry that is not in accordance with the stated clearances. UNPACKING YOUR MICROWAVE DRAWER Remove all packing materials from inside the microwave. DO NOT REMOVE THE WAVEGUIDE COVER, located on the top of the microwave drawer. Remove the feature sticker if there is one.
INSTALLATION INSTALLATION NOTICES Dimensions shown are precise, and cutout dimensions provide minimum clearances. • Contact surface must be solid and level. The cabinet floor of the opening should be constructed of plywood strong enough to support roughly 100 lb (45 kg). • Microwaves can be built into a cabinet by itself or under a gas or electric wall oven. Clearance between a wall oven and microwave must be a minimum of 2" (51 mm).
INSTALLATION 24" Microwaves Installation Cutouts and Clearances 30" Microwaves 10 *NOTE: Cabinet opening width varies with the 30" model. See page 12 for details.
INSTALLATION 3 1/2" (89 mm) 6" (152 mm) 5" (127 mm) 4" (102 mm) ELECTRICAL OUTLET AND ANTI-TIP BLOCK • To reduce the risk of tipping the drawer, an anti-tip block must be located a minimum of 15" (381 mm) above the cabinet floor on which the microwave drawer will sit, as outlined above. A wooden 6" (152 mm) anti-tip block must be provided by the installer. The anti-tip block prevents serious injury that might result from spilled hot liquids.
INSTALLATION DRAWER INSTALL ATION DRAWER INSTALLATION INSTALL ATION Figure 4 THE DRAWER Figure 4 24" Microwaves Mounting plate DRAWER INSTALLATION 1. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. Mounting screws 2. Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and wall. 1. Place the drawer adjacent to theall wall cabinet 3. Slide the drawer theorway until opening.
INSTALLATION HANDLES HANDLE INSTALLATION NOTE: The Allen/hex key needed to remove the handle is only included with Autograph Edition handles (Champagne Bronze, Polished Gold, and Matte Black). Autograph Edition handles 1. Locate the holes on the underside of each handle base. 2. Using a 7/64" Allen/hex key, turn counter-clockwise to loosen both the left and right set screws. 3. Carefully remove the handle. If installing an Autograph Edition handle, carefully place the new handle on the mounting studs.
INSTALLATION TRIM KIT TRIM KIT INSTALLATION NOTE: This trim kit is available for purchase as a separate accessory for ZLINE’s 24" microwave drawer in stainless steel only. The trim kit is only available for the 24" unit; it is Trim Kit Installation not available in black stainless.
INSTALLATION TRIM KIT TOOLS NEEDED: • Phillips-head screwdriver • Marker • Drill PARTS INCLUDED: PART QUANTITY 1 Support beam (2) 2 Front bracket (1) 1 Rear bracket (1) 1 Buckle seat (4) 4 Buckle (4) 4 Finishing washers (4) 4 #1 Screw (4) 4 #2 Screw (16) 16 #3 Screw (2) 2 Trim Kit Installation Outer trim (1) IMAGE 15
INSTALLATION TRIM KIT 1. Lay the support beams flat on the bottom of the cabinet cutout with the open sides facing each other (see Figure 1). Figure 1 To gauge proper width, temporarily place the rear and front brackets onto the support beams so the rear bracket lips slide into rear holes on top of the beams and the front Front bracket screw holes match to the front of the beams (see Figure 2).
INSTALLATION TRIM KIT 2. Remove the screws from the front bottom of your microwave. Using two of those screws, secure the front bracket to the bottom of thebracket microwave, ensuring the lip of the bracket is Front extending down and facing you. Next, remove the screws from the back bottom of the microwave and fasten the rear bracket, ensuring the two small lips are extended down and facing back (see Figures 4 and 5).
INSTALLATION TRIM KIT ① 4. 将安装好卡扣的外观框放在橱柜上作出比对；用记号笔画上安 Next, slide the outer trim into the cabinet cutout and use a marker or pencil to mark 装位置 where the buckles line up. Then, remove the trim and secure the four buckle seats into 卡扣的外观框放在橱柜上作出比对；用记号笔画上安 Place the trim kit which install buckle on the cabinet for ② 用 1#螺丝将卡座安装在对应安装位置上 the cabinet using the other eight #2 screws (see Figure 8).
INSTALLATION TRIM KIT 5. Using two people, lift the microwave and push it into the cabinet until the two small lips in the rear bracket slide into both holes in the rear of the support beams fastened in Step 1 to the bottom of the cutout (see Figure 10). 6. Use the two #3 screws to fasten the front bracket to the front of both support beams (see Figure 11). The microwave should now be firmly secured inside the cabinet cutout (see Figure 12).
INSTALLATION TRIM KIT ① Insert the trim kit into the corresponding buckle seat 将 预装好外观框卡进对应卡扣座里 7. Insert the outer trim kit into the cutout (see Figure 13). Clip each buckle onto its corresponding buckle seat to complete the trim kit installation (see Figure 14).
WARRANTY COVERAGE ZLINE Kitchen and Bath microwave parts will be warrantied for two years from the original purchase date for the original purchaser of the product. TERMS This warranty applies only to the original purchaser of the product installed for normal residential use. This is defined as a single-family, residential dwelling in a non-commercial setting.
WARRANTY The rating tag shows the model and serial number of your microwave. The tag is located below the control pad on the microwave. The tag is visible when the microwave door is open. Do not remove permanently affixed labels, warnings, or plates from the product. This will void the warranty. Need to purchase a part or accessory for your ZLINE product? Visit ZLINEparts.com, ZLINE's official parts distribution partner.
3.3.0 1-614-777-5004 www.zlinekitchen.com contact@zlinekitchen.
