Quick Start Guide 4-inch Thermal Imaging Product Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
Overview Thermal Imaging Temperature Detection Module Flash Near-infrared Flash Camera & Palm Collector Microphone Speaker 4-inch Touchscreen Reset Doorbell Button Card Reading Area USB Alarm 12V GND TX+ TXRX+ RX- Power In Ethernet Lock RS485 Wiegand In AL+ NO COM NC GND 485B 485A IWD0 IWD1 +12V GND ALGND AUX BUT SEN BELL+ BELLGND GND WD0 WD1 Auxiliary Input Exit Button Sensor Bell Wiegand Out Note: Not all products have the function with , the real product shall prevail.
Installation Environment Please refer to the following recommendations for installation. INSTALL INDOORS ONLY AVOID INSTALLATION NEAR GLASS WINDOWS AVOID DIRECT SUNLIGHT AND EXPOSURE AVOID USE OF ANY HEAT SOURCE NEAR THE DEVICE Recommended Palm Gestures 3 KEEP EFFECTIVE DISTANCE OF 30-50 cm KEEP SPACES BETWEEN YOUR FINGERS DO NOT KEEP YOUR FINGERS CLOSE DO NOT KEEP PALM OUTSIDE COLLECTION AREA DO NOT KEEP YOUR FINGERS FOLD/CURLED Note: 1. Place your palm within 30-50 cm of the device. 2.
Installation Requirements The installation requirements and indications associated with the device are given below: Specification Standard value Remark Operating Environment Indoor, Avoid wind, Avoid direct sunlight, 16°C to 35°C (60.8°F to 95°F) The recommended operating temperature is 25°C (77°F) Distance (between face 30cm to 120cm (0.98ft to 3.94ft) and device) Measurement Accuracy ±0.3°C (±0.54°F) The recommended distance is 80cm (2.62ft) This value is tested at a distance of 80cm or 2.
Standalone Installation Alarm Smoke Detector Door Sensor Exit Button Card Reader Lock TCP/IP ZKBioAccess IVS Power Connection 12V GND 12V DC GND Recommended AС Adapter 1) 12V ± 10%, at least 3000mA. 2) To share the power with other devices, use an AС Adapter with higher current ratings.
Ethernet Connection ZKBioAccess IVS TX+ TXRX+ RX- 1 2 3 4 5 6 7 8 RJ 45 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Default IP address: 192.168.1.201 Subnet mask: 255.255.255.0 Click [COMM.] > [Ethernet] > [IP Address] , input the IP address and click [OK]. Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment when connecting to ZKBioAccess IVS software.
Lock Relay Connection The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (normally opened when powered) is connected with 'NO1' and 'COM' terminals, and the NC Lock (normally closed when powered) is connected with 'NC1' and 'COM' terminals.
Wiegand Reader Connection Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last two pins are used by the Access Controller, as shown in the following figure. It sends the credentials to the device via wiegand communication. WD0 WD1 IWD0 IWD1 +12V GND Access Controller WD0 WD1 +12V GND Wiegand Reader RS485 Connection The RS485 lets user connect to multiple readers to the device. RS485 can be connected to the terminal, as shown in the figure below.
User Registration When there is no super administrator set in the device, click on to enter the menu. Add a new user and set User Role to Super Admin, then the system will request for the administrator’s verification before entering the menu. It is recommended to register a super administrator initially for security purposes. Method 1: Register on the device Click on > [User Mgt.] > [New User] to register a new user.
Method 2: Register on ZKBioAccess IVS software Please set the IP address and cloud service server address in the Comm. Menu option on the device. 1. Click [Access] > [Access Device] > [Device] > [Search] to search the device on the software. When an appropriate server address and port is set on the device, the searched devices are displayed automatically. Refresh New Delete Export Search Search Total Progress 192.168.213.
Method 3: Register on the phone Once the ZKBioAccess IVS software is installed, the users could enroll their face via a browser application on their own mobile phone. 1. Click [Personnel] > [Parameters], input ‘’http://Server address: Port’’ in the QR Code UGL bar. The software will automatically generate a QR code. Scan the QR code or login onto ‘’http://Server address: Port/app/v1/adreg’’ by the mobile phone to register users.
Ethernet and Cloud Server Settings Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Click on > [COMM.] > [Cloud Server Setting] to set the server address and server port, that is, the IP address and port number of the server after the software is installed.
Access Control Setting Click on > [Access Control] to enter the access control management interface and set relevant parameters of access control. Main Menu User Mgt. User Role Access Control Options Access Control COMM. Personalize Data Mgt.
Detection Management Settings > [System] > [Detection Management] to enter the setting interface. Click on ❶ You can set the value of High temperature alarm threshold, and enable the Temperature over the range; access denied and the Trigger external alarm, the device will send an alarm prompt when the temperature of the user detected exceeds the set value, meanwhile the user will be forbidden to access, as shown in the following figure. The method of enabling Mask detection is also the same.
Note: 1. The effective distance for temperature detection is within 30-50cm for the palm and 0.3-2m for the face. 2. Recommended for indoor use only. 3. Temperature measurement data is only for reference, and not for medical use. 4. Remove the mask to register the face, and wear the mask while recognizing the face. The type of mask, the size of the face covered by the mask, and bangs will affect the facial recognition process. 5. Facial verification for masked individuals will increase FAR.
As shown in the following figure. Real-Time Monitoring Welcome, admin 2020-05-22 11:03:07 Real-Time Monitoring Temperature Management Total: Real-Time Monitoring Abnormal Temperature 0 0 0 0 Normal Records Statistics Panel Temperature Raw Record Name: UnregisterUser Department: NULL Abnormal Temperature Record Temperature: 36.57°C 52.
QR Code as the Mobile Credential 1. 2. On the server, choose [System] > [Authority Management] > [Client Register] to add a registered App client. 3. Open the APP, enter the IP address or domain name of the server, and its port number, scan the Register QR-code. After the connection is successful, tap on Employee to switch to the Employee Login screen. Enter the Employee ID and Password (Default: 123456) to login. 4. Tap [Mobile Credential] on the APP, and a QR code will appear.
ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com Copyright 2021 ZKTECO CO., LTD. All Rights Reserved.
