User Manual Speed gates SBTL8000 Series Applicable Model(s): SBTL8000, SBTL8011, SBTL8022, SBTL8033, SBTL8200, SBTL8211, SBTL8222, SBTL8233 Date: September 2021 Doc Version: 1.0 English Thank you for choosing our product. Please read the instructions carefully before operation. Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are For further details, please visit our Company’s website www.zkteco.com.
Contents 1. Product Introduction ............................................................................................................................................................. 1 1.1 Model number and access control ...................................................................................................................... 1 1.2 Chassis design and dimensions .............................................................................................................................
1. Product Introduction 1.1 Model number and access control Access None Model SBTL8000 C3-200 and 2*Wiegand reader inBio 260 and 2* FR1500/ID reader √ √ SBTL8011 √ SBTL8022 √ SBTL8033 SBTL8200 SBTL8211 2*Facedepot 7B device √ √ √ SBTL8222 √ SBTL8233 Figure 1-1 1.2 Chassis design and dimensions The SUS304 stainless steel body looks simple and clean and is anti-corrosion. The SBTL8000 series grants legal access to the authorized persons and restricts illegal access.
Figure 1-2 1.3 The mechanical system of the speed gates The mechanical system of the swing turnstile is composed of the cabinet and the core mechanism. The cabinet is equipped with the mode indicator, the infrared sensor, and the locking system. The core mechanism mainly consists of the motor, the chassis, the core, and the swing arm (the glass panel). 1.
1.5 Operation principle of the speed gates When the device is connected to the power, the system will perform self-check. The device will operate normally if no problem is detected. If a failure is detected, the system will display related messages on the LCD display screen so that the user can have a quick knowledge of and solve the problem. Air switch Figure 1-3 When the reader detects a valid card/fingerprint, the display screen will show whether it is successful or not.
1.6 System composition of the product The single-passage management system is composed of two single-core speed gates. The multipassage management system is composed of two single-core barriers and multiple dual-core barriers. Working modes of the system To meet different needs, this system provides multiple working modes for users, including the normal working mode, normally open mode, normally closed mode, and testing mode.
2. Installation of the Product 2.1 Installation notes 1) It is recommended that the speed gates must be installed on a horizontal solid platform with a height of 50mm to 100mm. 2) It is also recommended that the swing turnstile should not be used in a corrosive environment. 3) Make sure the protective ground wire of the system is reliably connected to avoid personal injuries or other accidents. 4) The equipment shell is made of stainless steel.
Figure 2-2 2.3 Cables installation and fixing For the outlets of the concealed cables, please refer to the drawing indicating the mounting holes. The input voltage for this swing turnstile is AC110-220V, and its master and slave are connected with an 8-core cable (signal) and a 2-core cable (power). When installing the speed gates turnstile, the user only needs to connect it to the corresponding ports.
Figure 2-3a Mark the anchor hole at the centre of the stand, and the edge of the chassis base on the ground according to the size as shown in Figure 2-3a. Use a hammer drill to drill M12 screw holes, then install the screws. Place the swing turnstile according to the size and respective installation position as shown in the figure before installation and fixing.
perform a power-on test. If the test is passed, tighten the screws. It is recommended to mark a warning line on the ground, as shown in Figure 2-3b, after installing the device to remind the pedestrian to stand behind the line when swiping the card.
3. Menus 3.1 Menu operations Operating instruction 1) After powered on, the LCD screen on the control board will display the default state showing the current working mode. 2) There are 4 buttons on the control board: UP, DOWN, ENT, and ESC, as shown in Figure 3-1. Figure 3-1 UP: to move upwards or increase the value. DOWN: to move downwards or decrease the value. ENT: to enter a menu setting item or confirm the current modified value. ESC: to return to the previous menu or cancel the current operation.
3.2 Menus 1. Position adjustment of the swing barrier Type: zero (default) Left limit Right limit 2. Passing mode Opening mode: Two-way swipe (default) Left free, Right swipe Left swipe, Right free Two-way free Left prohibit, Right swipe Left swipe, Right prohibit Left prohibit, Right free Left free, Right prohibit Two-way prohibit 3. Opening duration (Press ‘ENT’ to modify) After the gate is opened, it will automatically close if no one passes through within a certain time duration.
8. Swiping mode Method: Allow the card to be swiped in the channel (default) Do not allow card swiping in the channel 9. Reset counter Reset: Out counter (default) Into the counter All 10. Gate closing delay time Time: 0~10 (default 0) 11. Brake unlock mode Mode: Delay unlock (default) 12. Brake starting angle Angle: 1~10 (default 3) 13. Fire alarm signal Signal: right open Left open (default) Shut down 14. Volume setting Volume: off The value ranges from 1 to 16 (default 5).
18. Memory opening Whether to open: No (default) Yes 19. System working mode Mode: working mode (default) Test mode Restore to factory 20. Version number: Version: V9.0.
3.
4. Troubleshooting Number 1 Failure descriptions The mode indicator light does not respond or the indication is incorrect. Analysis and solution Check that the control panel mode indicator wiring is correct or that the contact is poor. Check the mode setting of the master and 2 After swiping the card, there is only a slave devices and the 8-core, 2-core speed gate unlocked. connection lines. See the wiring diagram for the specific connection circuit.
5. Product Maintenance 5.1 Chassis The chassis is made of SAE 304 stainless steel. When the device has been used for a long period, there may be rust or stain on the surface of the chassis. Remember to regularly sand the surface along the grain softly and carefully, then coat the surface with anti-rust oil. Avoid covering the infrared sensors. 5.2 Movement Cut off the power supply before maintenance. Then, open the door, wipe off dust on the surface, and lubricate the transmission mechanism.
ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com Copyright©2021 ZKTECO CO., LTD. All rights reserved.
